Set Current Year Selector; Set Current Date Selector - Larsen & Brusgaard Viso II Manual

VISO II Settings
True Airspeed (TAS) / Skydiver's Airspeed (SAS)
Press or
The active selection flashes.
to save setting and enter the Set Current Year
Press
selector.
NOTE: Jump data is continuously stored in both TAS and SAS.
Stored information may be displayed in either unit of measure-
ment by selecting the respective mode.
Recommendation:
When using the VISO II as a Speed-Meter in a big way base it
is recommended to set it to SAS.
SAS will show the same speed throughout the dive (at the
30
VISO II Settings

Set Current Year Selector

Alti-Meter/ S peed-Meter • Feet/ Meter when set to Alti-Meter • Mph/ Kmh when set to S peed-Meter • Altitude
offset • Dive T ype • T rue Airspeed (T AS )/ S kydiver's Airspeed (S AS ) • Set current year • S et current date • S et
current time • Preset jump counter • R eset jump counter • T urn the VIS OII O FF • P adlock window
Set Current Year
Press to increase year.
Press to decrease year.
Press to save setting and enter the Set Current Date selec-
tor.
32
VISO II Settings
Set Current Time Selector
Alti-Meter/ S peed-Meter • Feet/ Meter when set to Alti-Meter • Mph/ Kmh when set to S peed-Meter • Altitude
offset • Dive T ype • T rue Airspeed (T AS )/ S kydiver's Airspeed (S AS ) • S et current year • S et current date • Set
current time • Preset jump counter • R eset jump counter • T urn the VIS OII O FF • P adlock window
Set Current Time
Press to increase time.
Press to decrease time.
Press to save setting and enter the Preset Jump Counter selec-
tor.
Not e: Time format is HH:MM and in 24-hour format
34
to toggle between TAS and SAS.
VISO II Settings
same body position), whereas TAS will show a different speed throughout the dive
(the same body position, different air density).
Below are some recommendations and numbers for SAS:
A good base speed should be: 110-115 mph.
A high base speed should be: 120-125 mph (tendency to wobble when docking).
A slow base speed should be: 100-105 mph (jumpers start to go low).
See separate section on page 61 for more information about TAS and SAS.
VISO II Settings

Set Current Date Selector

Alti-Meter/ S peed-Meter • Feet/ Meter when set to Alti-Meter • Mph/ Kmh when set to S peed-Meter • Altitude
offset • Dive T ype • T rue Airspeed (T AS )/ S kydiver's Airspeed (S AS ) • S et current year • Set current date • S et
current time • Preset jump counter • R eset jump counter • T urn the VIS OII O FF • P adlock window
Set Current Date
Press to increase date.
Press to decrease date.
Press to save setting and enter the Set Current Time selec-
tor.
Not e: Date format is MM:DD.
VISO II Settings
Preset Jump Counter Selector
Alti-Meter/ S peed-Meter • Feet/ Meter when set to Alti-Meter • Mph/ Kmh when set to S peed-Meter • Altitude
offset • Dive T ype • T rue Airspeed (T AS )/ S kydiver's Airspeed (S AS ) • S et current year • S et current date • S et
current time • Preset jump counter • R eset jump counter • T urn the VIS OII O FF • P adlock window
Explanation
The VISO II can store up to 200 jumps in the logbook and numbers them starting
from the jump number that you preset here. The counter can be used to keep track
on the number of jumps and it can be reset at any time, but time and date for the
last reset remains stored and cannot be erased.
Preset Jump Counter
Press to increase the jump counter.
Press to decrease the jump counter.
Press to save setting and enter the Reset Jump Counter
selector.
31
33
35