2) Open the Front Grille by pulling right and left sides of the hook. 3) Loosen 1 of the right screw and detach the Terminal Cover. 4) Detach the thermistor from the Front Grille. 5) Loosen 2 fixing screws of Front Grille. Samsung Electronics...
Page 10
1) Take all the connector of PCB upper side (Main PCB) out. (Inclusion Power Cord) 2) Detach the outdoor unit connection wire from the Terminal Block. 3) Loosen 4 fixing screws of Ass'y Control-In. Tray Drain 1) Pull Tray Drain out from the Back Body. Samsung Electronics...
Page 11
1) Loosen the fixing screw and detach the Fan Motor & Motor Holder. Cross Fan 2) Detach the Fan Motor from the Fan. 3) Detach the Fan From the left Holder Bearing. Samsung Electronics...
Page 12
Cabinet-Side edge and a fixing screw on the Cabinet-Front lower to detach the Cabinet-Front. 2) Loosen 2 fixing screws of the Ass'y-Control. 3) Loosen 6 fixing screws of the Cabinet-Side 4) Loosen 2 fixing screws of the Cabinet-Side Samsung Electronics...
Page 13
3) Disassemble the pipe in both inlet and outlet of the Compressor with welding torch. 4) Disassemble the pipe in both inlet and outlet of the Condenser with welding torch. 5) Loosen the 3 bolts at the bottom. 6) Detach the Compressor. Samsung Electronics...
Every time you push the button, the display panel reads . . . repeatedly. Setting Option SEG4. Push the button to set the display panel to Every time you push the button, the display panel reads . . . repeatedly. Samsung Electronics...
Page 19
Every time you push the button, the display panel reads . . . repeatedly. Setting Option SEG10. Push the button to set the display panel to Every time you push the button, the display panel reads . . . repeatedly. Samsung Electronics...
Page 20
If all lamps of indoor unit are flickering, Plug out, plug in power plug again and press ON/OFF key to retry. If the unit is not working properly or all lamps are continuously flickering after setting the option code, see if the correct option code is set up for its model. Samsung Electronics...
The compressor stops intermittently or the fan speed of the The compressor stops intermittently in a COOL mode or indoor unit decreases to prevent inside/outside air frozen DRY mode, and fan speed of the indoor unit decreases. depending on the inside/outside air temperature. Samsung Electronics...
Page 23
Problem with the outdoor unit or PCB outdoor unit remote control. • In 3 minutes, check the voltage No power source Problem with the relay (RY71) or PCB between the indoor unit terminal displayed. block N(1) and 1. Samsung Electronics...
Page 24
Check whether the fuse on the Replace fuse control board is normal. F701: 3.15[A]/250[V] Check the output of SMPS on the control board. Input power: AC230±15%[V] Replace the control board IC02 Input: DC 12[V] IC02 output: DC 5[V] Check the setting temperature Samsung Electronics...
Page 25
Test rod location Normal Voltage PCB CN72 Condition About AC pin #3 and #5 Fan operate 180V Replace Motor Motor Fan-Capacitor is out of order Fan-Capacitor Fan motor Fan motor is out of order. should be replaced. Samsung Electronics...
Page 26
Is rating voltage ±10% range applied relay between Power relay is Power relay should be Terminal block No. N(1) and No. 1 out of order replaced. Outdoor unit is out of order. Is the room sensor normal register? 10°C 20°C 30°C 17.96kΩ 12.09kΩ 8.3kΩ Samsung Electronics...
Page 27
Voltage at pin #57~#60 Micom (IC04) is faulty. of micom (IC04) change? (Squarewave) Voltage at pin #16 of IC06(ULN2003A) and #10~#12 of Driver IC06/08 (ULN2003A) is faulty. IC08(ULN2003A) change? (Squarewave) UP/DOWN louver motor is faulty. Samsung Electronics...
Page 28
SENSOR Resistance Value : 40˚C-5.83kΩ Connect the sensor to CN43, supply power, and measure the voltage of #1 and #2 of the CN43 connector. Poor ASS'Y PCB Replace Below 0.5V? Poor ASS'Y PCB Replace Over 4.9V? MICOM Error or Connector(CN43) check Samsung Electronics...
Page 29
When the voltage descends below 3V, the assembly module PCB is normal and the main PCB is poor. Then replace the main PCB. 3. Replace the assembly display PCB because the module PCB is poor if the voltage between No. 2~3 of CN91 maintains 5V after the remote control starts operation. Samsung Electronics...
Page 30
2) The fan motor of the indoor unit doesn't run. • Fan Motor Connector(CN72) is faulty • ASS'Y Main PCB is faulty 3) The power voltage between terminal #3 and #5 • Connection is faulty of the connector(CN72) is 0V. Samsung Electronics...
Page 31
32.430 3.537 6.941 14.680 33.890 3.652 7.192 15.280 35.430 3.772 7.455 15.900 37.050 3.897 7.729 16.550 38.760 4.026 8.015 17.240 40.560 4.161 8.313 17.960 Temperature Sensor Characteristic Curve Temperature (˚C) At the temperature of 25˚C(10KΩ) Resistance Value (Kohm) Samsung Electronics...
Page 32
∞, 0Ω . . . Open or Short Abnormal Stepping Motor Measure the resistance between the red wire and each terminal wire with a tester. Normal About 300Ω at the normal temperature (20˚C ~ 30˚C) ∞, 0Ω . . . Open or Short Abnormal Samsung Electronics...
6. Exploded Views and Parts List 6-1 Indoor Unit 3-8-1 You can search for the updated part code number through the ITSELF. URL : http://itself.sec.samsung.co.kr Samsung Electronics...
Page 35
Exploded Views and Parts List Parts List Q'TY Code No. Description Specification Remark SC09AWH SC12AWH DB94-00454B ASS'Y-BACK BODY ASS'Y DB61-01632A BACK-BODY HIPS DB69-00834A CUSHION-BACK BODY DB61-01634A SUPPORTER-EVAP RH HIPS DB31-00219A MOTOR-IN YDK-20S4F8C-1 DB94-00456A ASS'Y-CROSS FAN OD92x635 DB97-02075A ASS'Y BOLT-SPECIAL ASS'Y...
(H/M/L) BUZZER • STEPPING MOTOR DRIVE STEPPING MOTOR • BUZZER DRIVE FLAP : BLADE UP/DOWN ON, OFF TIMER SELECT TEMPERATURE DC 5V SELECT VOLTAGE REGULATOR SLEEP SELECT DC 12V ENERGY SAVING SMPS POWER BLOCK BATTERY CHECK AC INPUT Samsung Electronics...
1. Product Specifications 1-1 Table Model SC09AWH SC12AWH Item Indoor unit Outdoor unit Indoor unit Outdoor unit Type Wall-mounted Wall-mounted Cooling Dehumidifying Air Volume /min Perfor- mance Noise 38 / 36 / 34 51 / 51 41 / 39 / 37...
Page 52
CAPILLARY TUBE Freezer Oil Capacity Refrigerant to Change(R22) Protection Device(OLP) RAC12110-9622 RAC12074-9622 Cooling Test Condition INDOOR UNIT : DB27˚C WB19˚C OUTDOOR UNIT : DB35˚C WB24˚C Maximum Operation Condition INDOOR UNIT : DB32˚C WB23˚C OUTDOOR UNIT : DB43˚C WB28˚C Samsung Electronics...
Page 53
Freezer Oil Capacity Refrigerant to Change(R22) Protection Device(OLP) RAC12054-9622 RAC12074-9622 Cooling Test Condition INDOOR UNIT : DB27˚C WB19˚C OUTDOOR UNIT : DB35˚C WB24˚C Maximum Operation Condition INDOOR UNIT : DB32˚C WB23˚C OUTDOOR UNIT : DB43˚C WB28˚C Samsung Electronics Samsung Electronics...
Page 54
CAPILLARY TUBE Freezer Oil Capacity Refrigerant to Change(R22) Protection Device(OLP) RAC12054-9622 RAC12074-9622 Cooling Test Condition INDOOR UNIT : DB27˚C WB19˚C OUTDOOR UNIT : DB35˚C WB24˚C Maximum Operation Condition INDOOR UNIT : DB32˚C WB23˚C OUTDOOR UNIT : DB43˚C WB28˚C Samsung Electronics...
Page 55
The On Timer enables you to switch on the air conditioner automatically after a given period of time that is from 1 hour to 24 hours. To set the operating time, press the button one or more times until the required time display. Samsung Electronics...
Page 56
On Timer or Off Timer set. Battery life indicator. If you want to check the battery life, press the button. The longer will remain the battery life. If one battery life indicator remains, replace new batteries. Samsung Electronics...
Page 57
SLEEP MODE : Sleep mode is available only in COOL mode. The operation will stop after 6 hours. *In COOL mode : The setting temperature is automatical- ly raised by 1°C each 1hour When the temperature has been raised by total of 2°C, that temperature is maintained. Samsung Electronics...
Electric and earth work shall meet the "Electric Facility Technology Standard" and the "Internal Wire Regulation" of the Electric Business Laws. I Inspection & Trial Run Upon completion of the tests, you shall make a trial run while you explain the main functions of the air conditioner to finish the installation. Samsung Electronics...
3-Way valve. And mount the service port cap to 3-Way valve. (gas) 7) Check for gas leakage. - At this time, especially check for gas leakage from the 3-Way valve’s stem nuts, (liquid) and from the service port cap. Valve stem Stem cap Samsung Electronics...
Page 60
7) Stop operation of the air conditioner. 8) Close the 3-Way valve, disconnect the pressure gauge, and open the 3-Way valve again. 9) Close the cap of each valve. Samsung Electronics...
Page 61
• Make sure you do not bend the connection pipes in the middle and store together with the cables. • Move the indoor and outdoor units to a new location. • Remove the mounting plate for the indoor unit and move it to a new location. Samsung Electronics...
Page 62
2) Open the Front Grille by pulling right and left sides of the hook. 3) Loosen 1 of the right screw and detach the Terminal Cover. 4) Detach the thermistor from the Front Grille. 5) Loosen 2 fixing screws of Front Grille. Samsung Electronics...
Page 63
1) Take all the connector of PCB upper side (Main PCB) out. (Inclusion Power Cord) 2) Detach the outdoor unit connection wire from the Terminal Block. 3) Loosen 4 fixing screws of Ass'y Control-In. Tray Drain 1) Pull Tray Drain out from the Back Body. Samsung Electronics...
Page 64
1) Loosen the fixing screw and detach the Fan Motor & Motor Holder. Cross Fan 2) Detach the Fan Motor from the Fan. 3) Detach the Fan From the left Holder Bearing. Samsung Electronics...
Page 65
Cabinet-Side edge and a fixing screw on the Cabinet-Front lower to detach the Cabinet-Front. 2) Loosen 2 fixing screws of the Ass'y-Control. 3) Loosen 6 fixing screws of the Cabinet-Side 4) Loosen 2 fixing screws of the Cabinet-Side Samsung Electronics...
Page 66
3) Disassemble the pipe in both inlet and outlet of the Compressor with welding torch. 4) Disassemble the pipe in both inlet and outlet of the Condenser with welding torch. 5) Loosen the 3 bolts at the bottom. 6) Detach the Compressor. Samsung Electronics...
Every time you push the button, the display panel reads . . . repeatedly. Setting Option SEG4. Push the button to set the display panel to Every time you push the button, the display panel reads . . . repeatedly. Samsung Electronics...
Page 68
Every time you push the button, the display panel reads . . . repeatedly. Setting Option SEG10. Push the button to set the display panel to Every time you push the button, the display panel reads . . . repeatedly. Samsung Electronics...
Page 69
If all lamps of indoor unit are flickering, Plug out, plug in power plug again and press ON/OFF key to retry. If the unit is not working properly or all lamps are continuously flickering after setting the option code, see if the correct option code is set up for its model. Samsung Electronics...
Page 74
1,200 1,100 1,000 15.0 15.0 Length of Connecting Pipe(m) Length of Connecting Pipe(m) 12,000Btu Power consumption(Cooling) Cooling Capacity 3.70 1,350 3.50 1,300 3.30 1,250 3.10 1,200 1,150 2.90 15.0 15.0 Length of Connecting Pipe(m) Length of Connecting Pipe(m) Samsung Electronics...
Page 75
The compressor stops intermittently or the fan speed of the The compressor stops intermittently in a COOL mode or indoor unit decreases to prevent inside/outside air frozen DRY mode, and fan speed of the indoor unit decreases. depending on the inside/outside air temperature. Samsung Electronics...
Page 76
Problem with the outdoor unit or PCB outdoor unit remote control. • In 3 minutes, check the voltage No power source Problem with the relay (RY71) or PCB between the indoor unit terminal displayed. block N(1) and 1. Samsung Electronics...
Page 77
Check whether the fuse on the Replace fuse control board is normal. F701: 3.15[A]/250[V] Check the output of SMPS on the control board. Input power: AC230±15%[V] Replace the control board IC02 Input: DC 12[V] IC02 output: DC 5[V] Check the setting temperature Samsung Electronics...
Page 78
Test rod location Normal Voltage PCB CN72 Condition About AC pin #3 and #5 Fan operate 180V Replace Motor Motor Fan-Capacitor is out of order Fan-Capacitor Fan motor Fan motor is out of order. should be replaced. Samsung Electronics...
Page 79
Is rating voltage ±10% range applied relay between Power relay is Power relay should be Terminal block No. N(1) and No. 1 out of order replaced. Outdoor unit is out of order. Is the room sensor normal register? 10°C 20°C 30°C 17.96kΩ 12.09kΩ 8.3kΩ Samsung Electronics...
Page 80
Voltage at pin #57~#60 Micom (IC04) is faulty. of micom (IC04) change? (Squarewave) Voltage at pin #16 of IC06(ULN2003A) and #10~#12 of Driver IC06/08 (ULN2003A) is faulty. IC08(ULN2003A) change? (Squarewave) UP/DOWN louver motor is faulty. Samsung Electronics...
Page 81
SENSOR Resistance Value : 40˚C-5.83kΩ Connect the sensor to CN43, supply power, and measure the voltage of #1 and #2 of the CN43 connector. Poor ASS'Y PCB Replace Below 0.5V? Poor ASS'Y PCB Replace Over 4.9V? MICOM Error or Connector(CN43) check Samsung Electronics...
Page 82
When the voltage descends below 3V, the assembly module PCB is normal and the main PCB is poor. Then replace the main PCB. 3. Replace the assembly display PCB because the module PCB is poor if the voltage between No. 2~3 of CN91 maintains 5V after the remote control starts operation. Samsung Electronics...
Page 83
2) The fan motor of the indoor unit doesn't run. • Fan Motor Connector(CN72) is faulty • ASS'Y Main PCB is faulty 3) The power voltage between terminal #3 and #5 • Connection is faulty of the connector(CN72) is 0V. Samsung Electronics...
Page 84
32.430 3.537 6.941 14.680 33.890 3.652 7.192 15.280 35.430 3.772 7.455 15.900 37.050 3.897 7.729 16.550 38.760 4.026 8.015 17.240 40.560 4.161 8.313 17.960 Temperature Sensor Characteristic Curve Temperature (˚C) At the temperature of 25˚C(10KΩ) Resistance Value (Kohm) Samsung Electronics...
Page 85
∞, 0Ω . . . Open or Short Abnormal Stepping Motor Measure the resistance between the red wire and each terminal wire with a tester. Normal About 300Ω at the normal temperature (20˚C ~ 30˚C) ∞, 0Ω . . . Open or Short Abnormal Samsung Electronics...
Page 87
6. Exploded Views and Parts List 6-1 Indoor Unit 3-8-1 You can search for the updated part code number through the ITSELF. URL : http://itself.sec.samsung.co.kr Samsung Electronics...
Page 88
Exploded Views and Parts List Parts List Q'TY Code No. Description Specification Remark SC09AWH SC12AWH DB94-00454B ASS'Y-BACK BODY ASS'Y DB61-01632A BACK-BODY HIPS DB69-00834A CUSHION-BACK BODY DB61-01634A SUPPORTER-EVAP RH HIPS DB31-00219A MOTOR-IN YDK-20S4F8C-1 DB94-00456A ASS'Y-CROSS FAN OD92x635 DB97-02075A ASS'Y BOLT-SPECIAL ASS'Y...
Page 98
6-3 Ass'y-Control In(Code No : DB93-02481 ) Code No. MODEL Code No. MODEL DB93-02481B SC09AWH/EDC, SC12AHW/EDC, SC09ZWH/EDC, DB93-02481H KF-35G/SWA SC12ZWH/EDC, AS09WHWE/XSS, AS12WHWE/XSS, DB93-02481K KF-25G/SWA AS09WHWE/SMR, AS12WHWE/SMR DB93-02481M AS09WHWD/XSE, AS12WHWD/XSE DB93-02481D SC09ZWH/XSA, SC12ZWH/XSA Parts List Code No. Description Specification Q'TY Remark...
Page 99
(H/M/L) BUZZER • STEPPING MOTOR DRIVE STEPPING MOTOR • BUZZER DRIVE FLAP : BLADE UP/DOWN ON, OFF TIMER SELECT TEMPERATURE DC 5V SELECT VOLTAGE REGULATOR SLEEP SELECT DC 12V ENERGY SAVING SMPS POWER BLOCK BATTERY CHECK AC INPUT Samsung Electronics...
Page 100
6-3 Ass'y-Control In(Code No : DB93-02481 ) Code No. MODEL Code No. MODEL DB93-02481B SC09AWH/EDC, SC12AHW/EDC, SC09ZWH/EDC, DB93-02481H KF-35G/SWA SC12ZWH/EDC, AS09WHWE/XSS, AS12WHWE/XSS, DB93-02481K KF-25G/SWA AS09WHWE/SMR, AS12WHWE/SMR DB93-02481M AS09WHWD/XSE, AS12WHWD/XSE DB93-02481D SC09ZWH/XSA, SC12ZWH/XSA Parts List Code No. Description Specification Q'TY Remark...
8. Wiring Diagram 8-1 Indoor Unit Code No : DB98-15959A This Document can not be used without Samsung's authorization. Samsung Electronics...
Page 102
8-2 Outdoor Unit MOTOR CAPACITOR FAN MOTOR COMP CAPACITOR O.L.P OVER LOAD PROTECTOR Code No : DB98-15966A This Document can not be used without Samsung's authorization. Samsung Electronics...
Page 103
9. Schematic Diagram 9-1 Indoor Unit This Document can not be used without Samsung's authorization. Samsung Electronics...