Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-18 FACTORY MODEL: LM568E MODEL: LCD 568LM (LM568E-CA) ) ID LABEL MODEL No. CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. MUTE MENU AUTO...
If the wires are pressed cause short and may • Do not modify original design without obtaining written burn or take fire. permission from LG or you will void the original parts and labor guarantee. TAKE CARE DURING HANDLING THE LCD MODULE WITH BACKLIGHT UNIT.
TIMING CHART VIDEO SYNC Total Video Blanking Sync Back Front Sync Frequency MODE H / V Resolution Period Active Time Duration Porch Porch Polarity Clock ( E ) Time ( A ) ( B ) ( D ) ( F ) ( C ) 25.175 31.468 KHz...
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW DC Power Connector MIC . MIC . OU T AU DIO D-Sub AUTO MUTE MENU Signal Connector Front Control Panel Power (DPMS) Indicator Power ON/OFF Button Front Control Panel AUTO MUTE MENU Power ON/OFF Button Note: Some signal from some graphics boards may not function properly.
DISASSEMBLY 1. TILT/SWIVEL & BACK COVER REMOVAL (1) Remove two screws (a). (2) Remove the Tilt/swivel. Back Cover (3) Remove two sheets. (3) Remove two screws (b) from the Back Cover. (4) Release six latchs (c). (5) Remove the Back Cover. M IC M IC D IO...
Page 8
3. MAIN PCB ASS’Y & CONTROL PCB , SOUND ASS’Y REMOVAL (1) Disconnect J4,J5 and J10 from the Main PCB Ass’y. (2) Remove six screws (a). (3) Remove the Main PCB Ass’y. (4) Remove three screws (b). (5) Disconnect J4 and J3 from the Sound Ass’y (6) Remove the Speaker PCB Ass’y.
Page 9
6. INVERTER ASS’Y REMOVAL (1) Disconnect CN2,CN3 and CN4,CN5 (2) Remove two screws (a). (3) Remove the Inverter Ass’y. - 9 -...
DESCRIPTION OF BLOCK DIAGRAM 1. Scaler One chip IC(GMZAN1, U3) GMZAN1 (U3) is one chip IC which it supports four internal function blocks of Video Amp, PLL, A/D converter and Video processor. Video signal (0.7Vp.p) clamped through C44, 45, 191 with matching IC’s proper cut off voltage. This signal is processed as a proper 8 bit digital signal by U3°Øs amplifying, phase locking, A/D converting, and scaling operations.
ADJUSTMENT All adjustment are thoroughly checked and corrected 2. Adjustment for White Balance when the monitor leaves the factory, but sometimes 1) Display color 0,0 pattern at Mode 12. several minor adjustment may be required. 2) Set External Bright to MAX position and Contrast to Adjustment should be following procedure and after MAX Position.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK ADAPTER, AND FIND OUT CHECK J1’S A SHORT POINT VOLTAGE AS OPENING (12V) ? EACH POWER LINE CHECK CHECK U4. U4 PIN 8 VOLTAGE (5V) ? CHECK CHECK L11 U5 Voltage (OPEN CHECK) (5V) ?
Page 14
2. NO RASTER (OSD IS NOT DISPLAYED) – INVERTER NO RASTER (OSD IS NOT DISPLAYED) J4 PIN10 CHECK ADAPTER 12V? CHECK MICOM INV J4 PIN5 ON/OFF PORT. 1. CONFIRM BRIGHTNESS OSD CONTRL STATE. J4 PIN1 2. CHECK MICOM DIM-ADJ PORT CHECK PULSE AS CONTACTING SCOPE...
Page 15
3. NO RASTER (OSD IS NOT DISPLAYED) – gmzanl NO RASTER (OSD IS NOT DISPLAYED) POWER PINS CHECK U2, U24 3.3V? 1. CHECK PIN141, 142 U3 PIN141, 142 SOLDERING CONDITION OSCILLATE AS 14.3M? 2. CHECK X2 3. TROUBLE IN U3 CHECK U9’S SOLDERING PIN31 IS 65MHz CLOCK? CONDITION AND...
Page 16
4. NO RASTER (OSD IS DISPLAYED) – gmzanl NO RASTER (OSD IS DISPLAYED) POWER PIN CHECK U2, U24 3.3V? 1. CHECK PC CHECK 2. CHECK SIGNAL CABLE R,G,B INPUT? U3 PIN 87, 91, 95 & D-SUB CONNECTOR LINE CHECK CHECK H-SYNC LINE H-SYNC INPUT (D-SUB→U6 →U3 U3 PIN 150?
Page 17
5. NO SOUND NO SOUND CHECK SPEAKER CHECK SPEAKER ASS’Y? AUDIO PCB CHECK JACK(J7) CHECK INPUT SIGNAL & AUDIO CORD U3(TDA7449) PIN7,8? CHECK MAIN CHECK U3(MICOM) IIC LINE →AUDIO J3 →U3(TDA7449) CHECK INPUT SIGNAL CHECK U3(TDA7449) U1(TDA7496L) PIN4,9? CHECK OUTPUT SIGNAL CHECK U1(TDA7496L) U1(TDA7496L) PIN14,17?
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS MODEL: FLATRON LCD 568LM(LM568E-CA) DATE: 2001. 9. 12. MODEL: FLATRON LCD 568LM(LM568E-CA) DATE: 2001. 9. 12. *S *AL LOC.
Need help?
Do you have a question about the FLATRON 568LM LM568E-CA and is the answer not in the manual?
Questions and answers