Advertisement
BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY.
ASSEMBLE UNIT ON A
CLEAN,
FLAT SURFACE.
TOOLS NEEDED: ADJUSTABLE WRENCH, PHILLIPS HEAD SCREWDRIVER
Extra Hole
Venturi
Valve orifice
Ignition wire
Piezo ignitor
Page 9
customer service 1-855-893-2227, 9:00 a.m-6:00 p.m EST, Monday-Friday.
ASSEMBLY
Carefully position grill as shown.
Do not tighten screws all the way. Leg
frames may need to be adjusted during
assembly.
STEP 1
Attach rear legs (4), right front leg (20)
and left front leg (19) to bottom of smoker
body (1) using
eight 1/4-20x1/2" screws (A)
Note: The right front leg contains an extra
hole on its side and must be mounted at the
front in the position shown. This hole will be
used later to secure the gas hose to the leg
with a zip-tie.
Do not fully tighten screws
STEP2
Attach control panel assy(5) to right front
leg
20) as shown using
(
two 1/4-20x1/2"
screws(A)
Repeat on opposite side attaching
control panel (5) to left front leg (19).
STEP 3
Position burner box assy(6) over center
hole in bottom of smoker body,
carefully aligning venturi over valve
orifice as shown. Attach burner box to
three 1/4-20x1/2"
smoker body using
screws(A)
Firmly attach ignition wire to piezo
ignitor on control panel as shown in
Figure B.
Figure B
Tighten all hardware at this time.
!
PERFORM "SOAPY WATER TEST" BEFORE EACH USE. SEE "SOAPY WATER TEST" SECTION IN
MANUAL. EXTINGUISH ALL OPEN FLAMES BEFORE CONNECTING REGULATOR TO GAS
CYLINDER. TURN GAS OFF AFTER EACH USE.
REGULATOR, BURNER AND GAS VALVE CONNECTION & OPERATION
Inspect hose before each use. If there are signs of
wear, cuts, or leaks, replace unit. DO NOT USE.
Inspect burner before each use. Check burner and
burner ventura tube for insects and insect nests. A
clogged tube can lead to a fi re beneath appliance.
1.
Connect hose regulator to LP Gas Cylinder
Make sure gas cylinder valve is closed. Turn
knob clockwise until it stops.
2.
Make sure control knob on smoker is in the
"OFF" position.
Remove protective cap from
3.
gas cylinder and coupling
nut if applicable.
4.
Center and insert regulator
nipple into valve outlet on
gas cylinder as shown in fi
gure on the left. Turn
regulator coupling nut
clockwise until it stops. DO
NOT OVER TIGHTEN.
Perform Soapy Water Test.
To use turn gas cylinder ON, turn regulator control
valve ON, turn burner control knob clockwise and
push ignitor button to light.
If ignition does not take place within five seconds,
turn gas control valve to off position and wait fi ve
minutes and repeat lighting procedures. If ignition still
MATCH LIGHT INSTRUCTION
1. Read all instructions and warnings before lighting.
2. Check gas control valve and gas cylinder valve to be
certain it is in OFF position before connecting to gas
cylinder. Perform soapy water test before each use.
3. Open door during lighting.
4. Turn gas control valve on, turn gas cylinder valve on.
5. Place a long, lit fi replace match stick close enough to
burner to ignite.
customer service 1-855-893-2227, 9:00 a.m-6:00 p.m EST, Monday-Friday.
!
does not occur, see match light directions below.
After use turn burner control knob OFF, turn regulator
control valve OFF, then turn gas cylinder OFF.
Burner control knob adjusts burner flame. Turn control
knob clockwise SLOWLY to increase fl ame. Turn
control knob counter-clockwise to decrease flame and
shut flame off.
Visually check burner fl ame. A CORRECT FLAME
should be blue with a small amount of yellow at the tip.
An INCORRECT FLAME is excessively yellow and
irregular. If an incorrect flame occurs, turn burner
control knob to "OFF
position,
turn off regulator and
propane tank. Allow unit
to cool and then clean
burner.
Let burner completely
dry before re-lighting.
The hose with zip tie
be captured at the right
front leg at anytime
and check before
ignition. (Please see
ASSEMBLY
INSTRUCTION STEP
12)
6. After each use, fi rst
turn gas control valve off,
then gas cylinder valve
off. Always allow unit to
cool completely before
touching, moving or
storing.
Page 6
Advertisement
