TSB41AB1 IEEE 1394a 2000 ONE PORT CABLE TRANSCEIVER/ARBITER SLLS423D – JUNE 2000 – REVISED SEPTEMBER 2002 description (continued) required for normal network operation regardless of the state of the PHY-LLC interface. When the interface is in the reset or disabled state and LPS is again observed active, the PHY initializes the interface and returns it to normal operation.
TVP5146 1.7 Terminal Functions Table 1–1. Terminal Functions TERMINAL DESCRIPTION NAME NUMBER Analog Video VI_1_A VI_1_x: Analog video input for CVBS/Pb/B/C VI_1_B VI_2_x: Analog video input for CVBS/Y/G VI_1_C VI_3_x: Analog video input for CVBS/Pr/R/C VI_2_A VI_4_A: Analog video input for CVBS/Y VI_2_B Up to 10 composite, 4 S-video, and 2 composite or 3 component video inputs (or a combination thereof) VI_2_C...
Page 14
TVP5146 Table 1–1. Terminal Functions (Continued) TERMINAL DESCRIPTION NAME NUMBER Host Interface I 2 C clock input I 2 C data bus Power Supplies AGND Analog ground. Connect to analog ground. A18GND_REF Analog 1.8-V return A18VDD_REF Analog power for reference 1.8 V CH1_A18GND CH2_A18GND Analog 1.8-V return...
2-Input 1-Output Video Switch (75Ω driver)/3-Input 1-Output Video Switch (75Ω driver) MM1221~1228 MITSUMI 2-Input 1-Output Video Switch (75Ω driver)/3-Input 1-Output Video Switch (75Ω driver) Monolithic IC MM1221~MM1228 Outline These ICs are high grade video switches with 2-input 1-output or 3-input 1-output and built-in 75Ω driver. The series includes those with and without built-in clamp and 6dB amp circuits.
Page 22
2-Input 1-Output Video Switch (75Ω driver)/3-Input 1-Output Video Switch (75Ω driver) MM1221~1228 MITSUMI Block Diagram (MM1221~MM1228) Control input truth table Control input truth table Control input truth table Control input truth table...
July 2003 LP2995 DDR Termination Regulator General Description Features n Low output voltage offset The LP2995 linear regulator is designed to meet the JEDEC SSTL-2 and SSTL-3 specifications for termination of DDR- n Works with +5v, +3.3v and 2.5v rails SDRAM.
Page 28
TERMINATION TERMINATION AT E5.1 AT DDR The VTT side of the terminaton resistors should be placed on a wide VTT island on the surface layer. The island is located at each end of the bus, so it does not interfere with the signal routing.
PARTS LIST POWER ITEM DESCRIPTION LOCATION 0000273 CARBON FILM RESISTOR 1/4W33Ω±5%10mm 0000278 CARBON FILM RESISTOR 1/4W330Ω±5%10mm 0000279 CARBON FILM RESISTOR 1/4W470Ω±5%10mm 0000283 CARBON FILM RESISTOR 1/4W1K±5%10mm 0000289 CARBON FILM RESISTOR 1/4W4.7K±5%10mm 0000294 CARBON FILM RESISTOR 1/4W10K±5%10mm R3,R22 0000301 CARBON FILM RESISTOR 1/4W47K±5%10mm 0000361 CARBON FILM RESISTOR 1/4W1.2K±5%10mm 0000432 CARBON FILM RESISTOR 1/4W150Ω±5%10mm 0000286 CARBON FILM RESISTOR 1/4W2.2K±5%10mm...
Page 71
PARTS LIST POWER ITEM DESCRIPTION LOCATION 47.2 0880800 IC 431L TO-92 IC3,IC5 0881326 IC PQ12RD21TO-220 0881934 IC FSDM0565R TO-220F-6L 1000004 INDUCTOR IRON UT-20 40mH ±20% 10×13 1050002 THERM RESISTOR NTC SCK-104MS±20% 1080005 OPTOTRANSISTOR NEC2561 52.1 1080006 OPTOTRANSISTOR PC817 52.2 1080007 OPTOTRANSISTOR NEC2501 52.3 1080011 OPTOTRANSISTOR...
Need help?
Do you have a question about the DW9916S and is the answer not in the manual?
Questions and answers