Advertisement
Available languages
Available languages
Models: SP1, SP2, SP3 & SP820
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice:
When using electrical appliances, basic precautions should
be followed to reduce the risk of fire, electric shock, and injury
to persons, including the following:
If the appliance is damaged, check immediately with the supplier
before installation and operation.
Do not use this heater in the immediate surroundings of a bath,
shower or swimming pool.
Do not use outdoors.
This heater must not be located immediately above or below a
fixed socket outlet or connection box.
Do not cover or obstruct in any way the heat outlet grille located
underneath the heater. Overheating will result if the heater is
accidentally covered.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
The supply cord must be placed on the right hand side of the
heater away from the heat outlet underneath the heater.
Although this heater complies with safety standards, we do
not recommend its use on deep pile carpets or on long hair
type of rugs.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it safely.
Children should be supervised to ensure that they do not play
with the appliance.
The appliance must be positioned so that the plug is accessible.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or similarly qualified person in
order to avoid a hazard.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage marked
on the heater must correspond to the supply voltage.
Do not switch the appliance on until properly installed. Please read all
the safety warnings and operating instructions.
General
Unpack the heater carefully and retain the packaging for possible future
use, in the event of moving or returning the fire to your supplier.
Contents of Carton
•
Heater.
•
Wall fixing bracket.
•
Fixing screws and wall plugs.
•
Remote control and batteries ( 3 AAA's type).
•
Spare bulb.
Do not connect the heater to an electricity supply until it is installed on a
wall correctly. - see 'Installation'.
A choice of 1kW or 2kW heat output is provided by the fan heater, which
is concealed underneath the unit.
The heater can be used remotely or manually. - see 'Operation'.
General features of remote control are:
•
Heat output can be increased or decreased according to your
particular requirements.
•
The illumination of fuel effect can be increased or decreased.
Please note: Used in an environment where background noise is
very low, it may be possible to hear a sound which is related to the
operation of the flame effect. This is normal and should not be a
cause for concern.
- 3 -
Installation
Do not connect appliance until properly fixed to the wall and the
Instruction leaflet is read fully.
The minimum distances must be observed.
For installation of the appliance, care must be taken not to damage
concealed cables.
Please be careful while drilling the holes.
This model is designed to be permanently fixed to a wall at a minimum
height of 300mm.
The wall bracket must be fitted horizontally and the cable routed to the
bottom right of the heater as in Fig. 1.
A height of 600mm from bottom of heater to floor is recommended for
optimum viewing of fuel bed (see Fig. 2 for recommended fixing
dimensions).
For optimum viewing mark the top two screw fixing positions on wall in
accordance with the recommended fixing dimensions - see Fig. 2.
Fix the wall bracket using the two plugs and screws provided - see
Fig. 3.
Carefully lift the heater up ensuring that the top rear ledge of heater
engages the wall bracket and is sitting centrally positioned. - see Fig. 4
(b).
Rotate the bottom fixing bracket down. - see Fig. 4 (c).
Gently bring the heater level with the wall. - see Fig. 4 (d).
Mark the bottom hole position (see Fig. 5), remove the heater ensuring
that the bottom fixing bracket is rotated up.
Drill and fit wall plug.
Refit the heater to the wall fixing bracket (i.e. follow steps as in Fig. 4 a,
b, c and d) and rotate the bottom fixing bracket down again and use the
screw provided to permanently fix the heater in place.
The heater should not be connected until the instruction leaflet is read
fully.
Manual Operation
The switches are located at the right side of the heater.
The Standby Switch (Switch S1) must be first turned 'ON' and the AUTO/
MAN (Switch S2) switch set to 'MANUAL' to operate the manual controls
- see Fig. 6.
Note : When the fire is put in Manual mode the first time the flame effect
will come on indicated by the Bottom neon coming on for 3 seconds -
see Fig. 7.
Remote Operation
The standby switch (S1) must first be turned 'ON' and the 'AUTO/MAN'
Switch turned to 'AUTO'.
Note: It takes some time for the receiver to respond to the transmitter.
DO NOT PRESS the buttons more than once within two seconds for
correct operation.
Manual & Remote Operation
Setting
Flame Effect
Flame Effect & 1Kw Heat
Flame Effect & 2Kw Heat
To go to the previous settings press the ' O ' button (Switch S3).
Pressing the ' O ' button on the remote turns off the light &
To resume press the ' I ' button until the desired setting is reached - see
Fig. 8.
To increase or decrease the brightness of the flames, use the dimmer
button (Switch S4 on the fire or the
You can have any setting between full brightness and the flames totally
off. The heat setting will remain the same.
To turn off the power the Standby Switch (Switch S1) must be turned
'OFF'.
Note : Every time that manual mode is selected the previous light and
heat settings come on automatically.
Operation
Press the ' I ' button (Switch 3)
Press the ' I ' button again (Switch 3)
button on the Remote Control).
UK
Setting
Bottom Neon
Middle Neon
Top Neon
heat settings.
Advertisement
