Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ATX ivis
Summary of Contents for ATX ivis
- Page 1 IVIS IVIS - Indoor Video Insertion System Installation & Operation Manual...
- Page 2 Specifications subject to change without notice. MDU Solutions , UCrypt , DigiVu and VersAtive Pro are registered trademarks of ATX in the United States and/or other countries. Products or features contained herein may be covered by one or ® ® ® ®...
-
Page 3: Table Of Contents
3.1. Agile Modulator Front Panel Controls....................3-1 RF LEVEL ADJUSTMENT ......................... 4-1 SERVICE & SUPPORT ..........................5-1 5.1. Contact ATX Networks ........................5-1 5.2. Warranty Information ......................... 5-1 5.3. Safety ..............................5-1 MDU Solutions – IVIS Indoor Video Insertion System - Instalation & Operation Manual ®... - Page 4 Index of Figures Figures #1 IVIS Unit.......................1-1 #2 Agile Modulator ....................3-1 #3 Functional Schematic ..................4-1 MDU Solutions – IVIS Indoor Video Insertion System - Instalation & Operation Manual ®...
-
Page 5: Introduction
The agile modulator will easily tune to the new channel where fixed modulators need to be removed from the IVIS chassis and replaced with a modulator that is tuned to the new channel number. The chassis is easily opened and allows removal and replacement of the channel deletion filters and/or Video/Audio Modulators. - Page 6 CHAPTER 1: INTRODUCTION This page left intentionally blank. MDU Solutions – IVIS Indoor Video Insertion System - Instalation & Operation Manual ®...
-
Page 7: Installation
INSTALLATION Installation The IVIS unit can be mounted in a 19” rack housing or another appropriate cabinet for secure operation. All RF and BaseBand signal ports accept standard F connectors mounted on drop cables (RG-6/u, RG-11/u or similar). Connect the incoming Cable TV feed to the INPUT port and connect the OUTPUT port to your distribution system. Connect Video and Audio signals to one or both (if two Video/Audio sources present) Modulators. - Page 8 CHAPTER 2: INSTALLATION This page left intentionally blank. MDU Solutions – IVIS Indoor Video Insertion System - Instalation & Operation Manual ®...
-
Page 9: Agile Modulator Operation
All level controls are located on the front panel for ease of operation. The modulator’s maximum RF Output level at IVIS Output connector is +33 dBmV and is adjustable over a 10 dB range on the modulator front panel by using RF Output Level control, and is adjustable an additional 20 dB by utilizing the common front panel attenuator. - Page 10 CHAPTER 3: AGILE MODULATOR OPERATION This page left intentionally blank. MDU Solutions – IVIS Indoor Video Insertion System - Instalation & Operation Manual ®...
-
Page 11: Rf Level Adjustment
System, as well as Audio and Video Source Signals to corresponding Modulator Audio and Video Inputs, while monitoring the signal level at the IVIS -20 dB RF OUT TEST Point with a Spectrum Analyzer or RF Signal Level Meter, you should be able to measure the new Modulator’s Video and Audio carrier levels as well as the Video carrier levels for Analog signals or QAM... - Page 12 CHAPTER 4: RF LEVEL ADJUSTMENT This page left intentionally blank. MDU Solutions – IVIS Indoor Video Insertion System - Instalation & Operation Manual ®...
-
Page 13: Service & Support
Please contact ATX Technical Support for assistance with any ATX products. Please contact ATX Customer Service to obtain a valid RMA number for any ATX products that require service and are in or out-of-warranty before returning a failed module to the factory. - Page 14 1-501 Clements Road West, Ajax, ON L1S 7H4 Canada Tel +1 (905) 428-6068 Toll Free +1 (800) 565-7488 Fax +1 (905) 427-1964 Toll Free Fax +1 (866) 427-1964 www.atxnetworks.com support@atxnetworks.com Printed in Canada Rev. 04/16 (ANW0781)
Need help?
Do you have a question about the ivis and is the answer not in the manual?
Questions and answers