Related Manuals for Fervi 0500
Summary of Contents for Fervi 0500
- Page 1 OPERATION AND MAINTENANCE MANUAL Electronic cutting band saw for bench Art. 0500 TRANSLATION OF THE ORIGINAL INSTRUCTIONS...
- Page 2 Manual on the date of its issuance (shown in this page). On the other hand, the machine may also be subject to important technical changes in the future, without the manual being updated. Therefore, contact FERVI for information about modifications that may have been implemented. REV. 1...
-
Page 3: Table Of Contents
MACHINES AND ACCESSORIES CONTENTS INTRODUCTION ..................5 Preface..........................6 GENERAL SAFETY WARNINGS ..............7 General safety rules for machine tools ................7 Safety regulations regarding the electric system of machine-tools .......9 Safety rules for band saws ....................9 Technical Assistance .....................9 Other provisions ......................9 TECHNICAL SPECIFICATIONS .............. - Page 4 MACHINES AND ACCESSORIES 10.1.1 At the end of each machining................26 10.1.2 Periodically ......................26 10.2 Changing the bandsaw blade ................... 27 ELECTRICAL CIRCUIT ................29 SPARE PARTS..................29 TROUBLESHOOTING................32 WAREHOUSE STORAGE ................. 32 DISPOSAL OF PARTS AND MATERIALS........... 32 Pagina 4 di 32...
-
Page 5: Introduction
The purpose of this manual is to convey the necessary knowledge for the use and maintenance of Electronic cutting band saw for bench Art. 0500 and to create a sense of responsibility and knowledge of the capabilities and limits of this machine entrusted to the operator. -
Page 6: Preface
1.1 Preface For a safe and effective use of Electronic cutting band saw for bench Art. 0500, you must read this manual carefully to acquire full knowledge of the machine and the general precautions to be observed during operation. -
Page 7: General Safety Warnings
MACHINES AND ACCESSORIES GENERAL SAFETY WARNINGS 2.1 General safety rules for machine tools Risks related to Using the Machine Do NOT underestimate the risks related to the use of the machine and stay focused on the work you are carrying out. Risks related to Using the Machine Despite the implementation of all safety devices for safe use of the machine, it is necessary to take note of all the accident prevention requirements highlighted in various parts of this... - Page 8 MACHINES AND ACCESSORIES Keep the workplace tidy and free from hindrances; disorder causes accidents. Make sure that the work environment is forbidden to children, non-employees and animals. Do not perform tasks on the machine other than those for which it was designed. Only use the machine in the manner in which it was intended, as described in this instruction manual.
-
Page 9: Safety Regulations Regarding The Electric System Of Machine-Tools
MACHINES AND ACCESSORIES 2.2 Safety regulations regarding the electric system of machine- tools Risks associated with using the machine 1. Do not modify the electrical system in any way. Any attempt in this regard may jeopardize the operation of electrical devices, causing malfunction or accident. 2. -
Page 10: Technical Specifications
MACHINES AND ACCESSORIES 3 TECHNICAL SPECIFICATIONS Model Art. 0500 Height (mm) Width (including the reference bar) (mm) Depth (mm) Net weight (kg) Rated voltage (V) Power (W) 1800 Frequency (80 - 16000 Hz) Current (A) Blade size (mm) 1140 x 13 x 0.65... -
Page 11: Description Of The Machine
ACCESSORIES 4 DESCRIPTION OF THE MACHINE The B (Art. 0500) must only be used for cutting metal materials with the ENCH BAND SAW characteristics indicated below and within the limits recommended by the manufacturer and the safety and health norms. -
Page 12: Main Parts Of The Machine
MACHINES AND ACCESSORIES 4.1 Main parts of the machine Figure 1 - Overview of the Machine Base Belt speed adjustment knob Safety bracket for transport Blade guide locking lever Clamp activation lever Blade guide Clamp, piece-holder Blade (belt) Machine body Electric motor Saw tension lever Rotation unit... -
Page 13: Identification Label
MACHINES AND ACCESSORIES 4.2 Identification label The identification plate shown below is attached to the machine: Figure 2 – Identification plate 4.3 Pittogrammi The machine has the following pictograms: IT IS STRICTLY FORBIDDEN TO: Lubricate the blade: before, during and after use. ... - Page 14 MACHINES AND ACCESSORIES PLATE IN ITALIAN PLATE IN ENGLISH E’ ASSOLUTAMENTE VIETATO: IT IS STRICTLY FORBIDDEN TO: Lubrificare la lama: prima, Lubricate the blade before, during durante e dopo l’uso; and after use. Operare senza il guidalama Operate without the guide blade installato regolarmente...
- Page 15 MACHINES AND ACCESSORIES Figure 4 – Warning pictograms on the machine. Pagina 15 di 32...
-
Page 16: Description Of The Controls
MACHINES AND ACCESSORIES 5 DESCRIPTION OF THE CONTROLS 5.1 Start button Found on the control handle of the band saw (see Figure 5 and ref. 7 in Figure 1) is the start button of the blade, consisting of a sustained action safety button. -
Page 17: Cutting Speed Adjustment Knob
MACHINES AND ACCESSORIES 5.2 Cutting speed adjustment knob Positioned at the base of the control handle of the Band saw (see Figure 6 and ref. 9 in Figure 1) is the cutting speed adjustment knob. Figure 6 - Cutting speed knob To adjust the cutting speed of the blade, turn the adjustment knob in the following way: ... -
Page 18: Machine Safety Devices
MACHINES AND ACCESSORIES MACHINE SAFETY DEVICES 6.1 Electrical safety devices In the event of malfunction or breakdown, the B is equipped with a power ENCH BAND SAW cord and plug with a earthing lead that provides a path of minimal resistance to the electric current;... -
Page 19: Improper Use And Contraindications
MACHINES AND ACCESSORIES Use of PPE In any case, ALWAYS use appropriate personal protective equipment such as: Gloves; Goggles or face shields; Overalls or aprons; Safety shoes. Figure 7 - Personal Protective Equipment. 6.3 Improper use and contraindications The following actions described, which obviously can not cover the entire range of potential possibilities of "misuse"... -
Page 20: Transport And Lifting
MACHINES AND ACCESSORIES 7 TRANSPORT AND LIFTING The B weighs 20 kg, so it can be lifted and moved by hand by a single ENCH BAND SAW operator. To do so, follow the instructions below: Disconnect the power plug from the outlet and pick up the cable, making sure that will not be damaged during transport;... -
Page 21: Installation And Commissioning
MACHINES AND ACCESSORIES 8 INSTALLATION AND COMMISSIONING 8.1 Unpacking instructions The B is supplied ready for use, supplied with a band blade measuring 1140 ENCH BAND SAW mm x 13 mm x 0.65 mm and packed in a cardboard box. Before disposing of packaging, check that no parts of the machine, including the user manual or other documentation, are going to be thrown away. -
Page 22: Connection Of The Electric Power Supply Plug And Start Test
MACHINES AND ACCESSORIES 8.3 Connection of the electric power supply plug and start test 1. Insert the power supply plug into a grounded double pole socket (10/16 A, 230 V). 2. Start the machine by pressing the start button on the handle (see Figure 5) and make sure that the direction of rotation of the blade is as indicated by the arrow on the... -
Page 23: Operation
9.1 Instructions for Use Operating the machine The Bench band saw (Art. 0500) should only be used with certain metallic materials (section bars, stainless steel, copper, aluminium and its alloys). Do not cut "hardened or case-hardened" steel parts. - Page 24 MACHINES AND ACCESSORIES 4. After selecting the desired angle, tighten the angle locking nut (ref. 16 Figura 11). 5. Fit the reference rod into the hole (ref.17 in Figure 12) and secure it with the headless screw (ref.18 in Figure 12).
- Page 25 MACHINES AND ACCESSORIES To adjust the cutting speed of the blade, turn the adjustment knob in the following way: rotate clockwise to decrease the cutting speed; rotate anti-clockwise to increase the cutting speed. The cutting speed must be set according to the material to be cut, in line with the following specifications: 20 –...
-
Page 26: Maintenance
MACHINES AND ACCESSORIES 10 MAINTENANCE Any maintenance, except for that specifically listed in this manual should be performed by qualified staff authorized by the manufacturer. 10.1Routine maintenance 10.1.1 At the end of each machining Electric shock Before maintenance or checks, turn off the machine and ALWAYS unplug the plug from the power outlet. -
Page 27: Changing The Bandsaw Blade
MACHINES AND ACCESSORIES 10.2Changing the bandsaw blade Electric shock Before replacing the blade, turn off the machine and ALWAYS remove the plug from the power outlet. This is so that there is no risk of electric shock or undesired activation of the machine. Wear PPE ALWAYS wear suitable protective gloves (to reduce the risk of cut) when replacing the blade. - Page 28 MACHINES AND ACCESSORIES Figure 17 - Changing the bandsaw blade. 2. Using a screwdriver, remove the fixing screws of the rear protection guard (see Figure and ref.28 in Figure 17/C) and remove it. 3. Turn the blade tensioner lever (see ref.29 in Figure 16 Figure 17/D) to the "-"...
-
Page 29: Electrical Circuit
MACHINES AND ACCESSORIES 11 ELECTRICAL CIRCUIT Figure 18 - Diagram of the electrical circuit 12 SPARE PARTS Always clearly indicate: the symbol and the serial number of the machine; the code number of the parts; number of parts; ... - Page 30 MACHINES AND ACCESSORIES Pagina 30 di 32...
- Page 31 0500/60 Head body 05000/07 Spring 0500/34 Swivel body 0500/61 Lever 05000/08 Casing 0500/35 Rear bracket 0500/62 Bearing 05000/09 Extension cord 0500/36 Front bracket 0500/63 Intermediate gear 0500/10 Lever 0500/37 Knob 0500/64 Final gear 0500/11 S.F. screw 0500/38 Lock bar 0500/65...
-
Page 32: Pagina 3 Di
MACHINES AND ACCESSORIES 13 TROUBLESHOOTING PROBLEM PROBABLE CAUSE SOLUTION A) Damaged bearings. A) Contact Technical Support. B) Bearings not lubricated. B) Lubricate. C) Blade friction. C) Remove / replace the blade and Noisy operation. check sliding. D) Turn the blade tension lever. D) Blade loose.