Roland SDE-1000 Owner's Manual page 5

((DELAY
TIME))
:io
n
-MEMORY-
fSRoland
POWER
(7/
DELAY
TIME
Display
(I
a
DELAY
TIME
Button
;
't5
U
J
((MODULATION))
(5)
MODULATION RATE
Knob
This
sets
the rate of the
LFO
Modulation.
(D
MODULATION DEPTH
Knob
(8)
Modulation Rate
Indicator
@
MODULATION
Switch with Modulation
Indicator
Set the
MODULATION
Switch
(Q)
ON
(the indi-
cator
lights
up!,
then adjust the
Rate
and Depth
by
using the corresponding knobs
(5)
and
®.
The
Modulation Rate
Indicator
(8)
flashes at
the
same
rate as the-
LFO
Frequency
set
with
the
MODULA-
TION
RATE
Knob ®.
*The Modulation Rate Indicator
(8)
remainds
flash-
ing
whether
the
MODULATION
Switch
©
is
on
or
off.
'IjL'
Delay Range Switch with Delay Range Indicator
Select the delay range
with
the
Delay Range Switch
(\Z
(when "x
2"
position
is
selected,
the indicator
lights up),
then
set
the delay
time with the
DELAY
TIME
Button
@
.
The current delay time
is
shown
in
the
DELAY
TIME
Display
(j).
'The
DELAY
TIME
Button
is
used to
set
the Delay
Time.
Pressing
the upper
part
A
will
advance
the
figure
on
the Display,
making
the
Delay
Time
longer,
and
pressing
V
side will
shorten
it.
Pressing
one
side
while holding the other
side
down
will
quicken
this
change.
Delay
Time
Frequency
Characteristic
OFF
(x 1}
to
375ms
10 to
17kHz
{^idB)
ON
(x2) to
750ms
10
to
8
kHz
f^JdB)
*
The
Delay
Time shown
in
the Display
Window may
slightly alter after
a
while. Even
so,
there
is
nothing
to
worry about
it,
simply
adjust
it
right.
MODULATION
RATE
DEPTH
-DELAY
-MEM0RY-
M
I
I
U
I I
ULtUQ
Oaiif>
ON
01
[Roland
POWER
(fj)
Memory Channel
Selector Switches with
Memory
Channel Indicators
Four
different panel settings can be written into
Memory.
You
can
select
any of the four Channels
just
by
pressing
the switch. Delay Time,
as
well as
whether
the Delay Range,
DELAY
PHASE, Modu-
lation
and
FEEDBACK
Switches are on or off are
included
in
the panel
setting to
be written
into
memory.
*
Simply keep pressing
a
relevant Channel Switch for
about
two
seconds, and the Indicator of that
Channel Switch
wii! flash
showing
that writing
is
completed.
If
you
just
touch
the switch, the existing
panel setting
will
be recalled.
<0
©
DELAY PHASE
Switch with Delay Phase Indicator
With
this
switch,
the Phase of the delay
sound
can
be
inverted.
(J©
POWER
Switch
*The SDE-1000 remains
muted
for
about seven
seconds even after
turned on. Neither the
direct or
delay
sound
is
output.
The
panel setting
remains as
it
is
even
if
the
SDE-1000
is
turned
off.
(Refer to
P.7)
5