This guide assumes that the outdoor mounting structure to which the housing is attached is in place and that data and power cables have been pulled to the installation site. For the purpose of this guide we are installing the Illustra Pro PTZ camera to an EndCap Mount (ROENDC).
Attach the threaded adapter to the pendant adapter and tighten to secure. Attaching to the EndCap Mount (ROENDC): If the Illustra Pro PTZ Outdoor Housing is being attached to an existing mount it is essential that the EndCap (ROENDC) is replaced. Please contact your Tyco Security Products Sales Representative for further information.
Page 8
Illustra Pro PTZ Outdoor Housing Figure 1 Align the pendant adapter with the EndCap and rotate clockwise until approximately 6mm of the threaded adaptor is visible inside the EndCap. Attach the lock nut to the threaded adaptor and hold while rotating the pendant cap until secure as seen in Figure 2.
Page 9
Illustra Pro PTZ Outdoor Housing Attach the External Safety Lanyard: Wrap the safety lanyard around the pipe and thread end through the loop as seen in Figure 4. Figure 4 Attach the lanyard lock by threading the end of the safety lanyard through the hole in the lanyard lock as seen in Figure 5.
Page 10
Illustra Pro PTZ Outdoor Housing in the cables when attaching the outdoor housing in later steps. If audio cables are to be extended beyond 30m in length, they must be shielded. Note For ease of installation the power, alarm and audio cables should be routed through first, followed by the Ethernet cable.
Page 11
Illustra Pro PTZ Outdoor Housing Figure 8 Avoid touching the lens during position- ing and installation of the desiccant bag Insert the desiccant bag in the space between the camera mounting bracket and the inside surface of the housing as seen in Figure 9.
Page 12
Illustra Pro PTZ Outdoor Housing If required, a microSD memory card can be installed in the dome: Note The microSD card is an optional accessory and is not supplied with the dome. The maximum size of microSD card that can be used with the dome is 32GB. Contact your Tyco Security Products representative for further information.
Page 13
Illustra Pro PTZ Outdoor Housing Figure 12 Align the bubble assembly with the holes on the outdoor housing flange. The location ribs on the trim ring will fit between the fins on the outside of the housing as seen in Figure 13.
Page 14
Illustra Pro PTZ Outdoor Housing Figure 14 Repeat the process and securely tighten each screw using the tamperproof torx wrench in the sequence shown in Figure 14. Note Do not overtighten the screws as they may damage the trim ring assembly.
Page 15
Note The alarms and audio ports are only available on the Feature Plus version of the Illustra Pro PTZ Outdoor Housing, these ports will have watertight covers on all other versions. For ease of installation connect power, alarm and audio cables before connecting the Ethernet cable.
Page 16
Illustra Pro PTZ Outdoor Housing Using both hands to provide even pressure insert the outdoor camera housing into the pendant adapter until in the home position. Note Do not angle the outdoor camera housing when inserting it into the pendant adapter.
Page 17
Illustra Pro PTZ Outdoor Housing Figure 18 The camera housing is now supported. Tighten the two M8 screws highlighted in Figure 3 in the pendant adapter using the HEX L-Key Tool, to fully secure the outdoor camera housing. Push any excess cable into the EndCap and replace the access cover as seen in Figure Figure 19 Terminate the power cable using the ADSPOT (recommended) power supply.
Page 18
Illustra Pro PTZ Outdoor Housing If you are using another power source please refer to the documentation supplied with the unit. 3 Wire AC Supply Color 24Vac Black Yellow/Green 24Vac Black Note When using the ADSPOT power supply, ensure that the center tap jumper on the secondary side between 12v and GND has been removed.
Illustra Pro PTZ Outdoor Housing Specifications Electrical (combined dome and housing) • Input Voltage 22 to 30Vac, 50/60 Hz NEC Class 2/Certified Limited Power Source Maximum operation current 2.5A. Certified Limited Power Source Environmental • Operating Temperature –40°C to 50°C (–40°F to 122°F)
Page 20
Illustra Pro PTZ Outdoor Housing Quick Reference Guide...