Page 2
Wa�age, advanced safety protec�ons and ‘Vape while charging’ Technology. The CoolFire ACE has a variable voltage range of 3.0 – 7.5 volts adjustable in .1 volt increments and a variable wa�age range of 6.0 – 40.0 Wa�s, adjustable in .5 wa�s increments.
Page 3
Please check and verify that your CoolFire ACE is an authen�c Innokin Technology WARRANTY INFORMATION: product. Innokin Technology provides a 90 day a�er sales service warranty to all authorized To verify this CoolFire ACE is a real Innokin Technology device please: vendors.
Page 4
Please read this sec�on carefully to ensure you receive maximum benefits from your use with loose tobacco leaf or herbal substances. CoolFire ACE and enjoy vaping with it in the most safe and effec�ve ways possible. 4. This Advanced Personal Vaporizer has not been evaluated by the Food and Drug 1.
Page 5
We recommend that you use a high quality 5V 1A USB wall charger (CE/UL CoolFire ACE Advanced Personal Vaporizer. 12. Your CoolFire ACE Advanced Personal Vaporizer is not waterproof. Keep it dry at all �mes. Cer�fied). 13. Do not allow any liquids or ejuice to enter the device through the top threading 18.
Page 6
LED lights. Green = Almost fully Charged. Firing, POWER ON, Connector When the CoolFire ACE is fully recharged the LED light will go off. POWER OFF bu�on Yellow = Half Power. = Low Power. Charge the CoolFire ACE OLED Display Screen Heat dissipa�on...
Page 7
” three �mes to turn on the CoolFire ACE. Once the The Red LED and Ba�ery bar will blink when the ba�ery capacity is lower than 3.3V and CoolFire ACE is on, hold down the power bu�on to ac�vate the atomizer. When the CoolFire ACE will automa�cally power off.
Page 8
All CoolFire ACE se�ngs can be easily changed without the use of a menu system. source the CoolFire ACE can also be vaped and charged at the same �me with Innokin The large OLED screen readily displays all important informa�on.
Page 9
Pressing the power bu�on “ ” three �mes in rapid succession will power on the CoolFire ACE Advanced Personal Vaporizer. The main LED light will blink from red to To POWER OFF the CoolFire ACE : yellow to green a�er which the CoolFire ACE Advanced Personal Vaporizer will enter standby mode.
Page 10
Adjust Variable Voltage: increase or decrease the wa�age. Hold the bu�on down to quickly increase or decrease When the CoolFire ACE is in variable voltage mode press the "+" or "-" bu�on one �me the set wa�age. and then press it again to decrease the voltage. Hold the bu�on down to quickly increase or decrease the set voltage.
Page 11
Important: basic understanding of wa�age, voltage and coil resistance. There is a range of The CoolFire ACE will only fire variable voltage or variable wa�age depending on standard coil resistances: 2.1, 1.7, 1.4, 1.1, 0.8, 0.5 ohm etc and Rebuildable the last se�ng chosen;...
Page 12
The main CoolFire ACE ba�ery LED power light will blink from red to yellow to IMPORTANT Charging Informa�on: green, a�er which the CoolFire ACE ba�ery will enter standby mode. The final LED Only charge Innokin devices with a high quality CE/UL Cer�fied 5V/1A wall charger.
Page 13
Please skip the following sec�on about how to refill and replace a coil if it is How to replacing a coil of Slipstream Tank: express kit. CAUTION: Make sure there is no e-liquid in the Atomizer / Tank before you pull out the coil .
Page 14
Technical Specifica�ons: Opera�ng Voltage: 3.0V-7.5V Opera�ng Wa�age: 6.0W-40W Ba�ery: 1300mAh Standby current: 100uA max Maximum output Wa�age: 40W Maximum output Current: 12A Maximum output Voltage: 7.5V Clearomizer Resistance: 0.2Ohm (minimum) Charging: Micro USB DC5V/1A...
Need help?
Do you have a question about the Coolfire Ace and is the answer not in the manual?
Questions and answers