Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Online Manual
CD-IN Connector
Onboard AC97 CODEC
JP30 Die Hard BIOS Select Jumper
Die Hard BIOS with 100% Virus
Protection (Upgrade Optional)
Green: AUX-IN Connector
Red: Modem-IN Connector
CNR Expansion Slot
32-bit PCI Expansion Slot x6
nd
rd
2
& 3
USB Port Connector
Dr. LED Connector
WOM (Wake ON Modem) Connector
WOL (Wake ON LAN) Connector
IrDA Connector
Chassis Fan Connector with
H/W Monitoring
Front Audio Connector
®
PROMISE
FastTrak 100™ Lite IDE RAID
Controller (AX37D Plus Only)
Front Panel Connector
JP35 IDE RAID Controller
Enable/Disable Jumper
System & RAM Power Indicate LED
CMOS Data Clear Jumper
Chassis Intrusion Sensor Connector
SPP/EPP/ECP
PS/2 Mouse
Parallel Port
Connector
USB Port
PS/2 Keyboard
COM 1 Port
Connector
Game Port
PC99 Colored Back Panel
COM 2 Port
MIC-In
Line-In
Speaker Out
Resettable Fuse
Keyboard/Mouse Wake-up
Select Jumper
2200μf Low ESR
Condensers
ATX Power Connector
AUX Fan Connector
AGP 4x Expansion Slot
370-pin CPU Socket with
Frequency/Voltage
Auto-detection supports Intel
®
Pentium
III and Celeron™
533MHz~1GHz+
®
VIA
Apollo Pro266 Chipset
with Pure Aluminum Heatsink
CPU Fan Connector with
H/W Monitoring
184-pin DDR SDRAM Slot x2
support maximum up to 2GB
168-pin DIMM Slot x2
support PC100/PC133 SDRAM
maximum up to 2GB
JP23 FSB Select Jumper
ATA/33/66/100 IDE Connector x2
ATA/100 IDE RAID Connector x2
(AX37D Plus Only)
FDD Connector
®
Advertisement
Table of Contents
Related Manuals for AOpen AX37D PLUS
Summary of Contents for AOpen AX37D PLUS
- Page 1 168-pin DIMM Slot x2 support PC100/PC133 SDRAM ® PROMISE FastTrak 100™ Lite IDE RAID maximum up to 2GB Controller (AX37D Plus Only) Front Panel Connector JP23 FSB Select Jumper JP35 IDE RAID Controller Enable/Disable Jumper ATA/33/66/100 IDE Connector x2 ATA/100 IDE RAID Connector x2 System &...
-
Page 2: Jp14 Clear Cmos
2 and pin 3 of JP35 by Floppy Drive Cable x 1 jumper. USB Cable x1 (AX37D Plus Only) DDR Terminator x 1 Pin 1... -
Page 3: Installing Cpu
Tip: If your system hangs or fails to boot because of overclocking, simply use <Home> key to restore the default setting (433MHz) or you can wait the AOpen “Watch Dog Timer” reset the system in five seconds and system will auto-detect hardware again. -
Page 4: Jp23 Fsb/Pci Clock Ratio
Connect 34-pin floppy cable and 40-pin IDE cable to floppy connector FDC and IDE/IDE RAID (AX37D Plus only) connector. Be careful of the pin1 orientation. Wrong orientation 1. Make sure the module’s pin face down and match the socket’s size as depicted below. -
Page 5: Connecting Front Panel Cable
11. Connecting CD / AUX_IN / Modem (Optional) 9. Connecting ATX Power Connector The ATX power supply uses 20-pin connector shown below. Make sure you plug in the AUX-IN The CD-IN connector is used to connect CD Audio (Green) cable from CDROM or DVD drive to onboard sound. right direction. - Page 6 14. AOpen Bonus Pack CD 16. BIOS Upgrade AOpen Easy Flash is more user-friendly than traditional flash method. The BIOS binary You can use the autorun menu of Bonus CD disc. Choose the utility and driver and select file and flash routine are combined together and you simply run a single file to complete model name.
-
Page 7: Part Number And Serial Number
IDE cable. The problem should be caused by the Check if the system can IDE cables or HDD itself. reboot successfully. Re-install Windows 95, Windows 98 or Windows NT. AX37D Plus is model name of motherboard; R1.00 is BIOS version... - Page 8 Dear Customer, Test Report: We recommend to choose board/card/device from the Thanks for choosing AOpen products. To provide the best and fastest service to compatibility test reports for assembling your PC. our customer is our first priority. However, we receive numerous emails and http://www.aopen.com.tw/tech/report/default.htm...
Need help?
Do you have a question about the AX37D PLUS and is the answer not in the manual?
Questions and answers