Download  Print this page

Philips AJ3112/05 User Manual

Philips clock radio aj3112 compact design.
Hide thumbs


Clock Radio
Register your product and get support at
User manual
Meet Philips at the Internet
Printed in China AJ3112_05_UM_V1.1 (ASDA)
Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this
type of plug proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an
appropriate plug fitted in its place. If the mains plug contains a fuse, this should
have a value of 3 Amp. If a plug without a fuse is used, the fuse at the distribu-
tion board should not be greater than 5 Amp.
Note: The severed plug must be disposed of to avoid a possible shock hazard
should it be inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following code: blue = neutral
(N), brown = live (L). As these colours may not correspond with the colour mark-
ings identifying the terminals in your plug, proceed as follows:
• Connect the blue wire to the terminal marked N or coloured black.
• Connect the brown wire to the terminal marked L or coloured red.
• Do not connect either wire to the earth terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain that the cord grip is clamped over
the sheath of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may require consent. See Copyright Act 1956
and The Performer's Protection Acts 1958 to 1972.
Congratulations on your purchase and welcome to Philips!
To fully benefit from the support that Philips offers, register your
product at
CONTROLS (see fig. 1 )
1 DISPLAY - shows the clock/ alarm time and status of the set
2 ALARM indicator - lights up when alarm is activated
3 Frequency indicator - shows the radio frequency of your selected waveband
5 CLOCK - sets the clock time
7 ALARM RESET- stops the active alarm for 24 hours
8 ALARM - sets the alarm function
! Power cord - connects to wall outlet
@ Pigtail - improve FM reception
# VOLUME - adjusts the sound level
$ Battery door - opens to store a 9 volts 6F22 battery (not included) for clock
% FM/MW - selects FM/MW waveband
^ TUNING - tunes to radio stations
1 Check if the power supply, as shown on the type plate located on the bot-
2 Connect the plug to the wall outlet.
3 To disconnect the set from the power supply completely, remove the
For users in the U.K.: please follow the instructions on the lower left
handed corner of the sheet.
The clock memory backup allows your alarm and clock time settings to be stored
for up to a day when there is a power interruption e.g. power failure. The com-
plete clock radio and display illumination will be switched off. As soon as the
power supply returns, the display will indicate the correct time.
1 Remove the battery door to insert a 9 volts 6F22 type battery (not included)
2 Replace the battery door.
NOTE: If no backup battery is installed or the power interruption is prolonged,
Batteries contain chemical substances so they should be disposed of
- switches off the active alarm for a 8-9 minute period
- switches off the sleep function
- activates the radio for sleep function
- adjusts the sleep period
RADIO ON: switches on the radio
RADIO OFF: switches off the radio/alarm
ALARM - RADIO: activates the radio for alarm
ALARM - BUZ: activates the buzzer for alarm
- adjusts the hours / minutes for clock / alarm / sleep time
memory backup.
tom of the set, corresponds to your local power supply. If it does not, consult
your dealer or service center.
plug from the wall outlet.
for backup.
you will need to set the clock and alarm times again.


Table of Contents

   Related Manuals for Philips AJ3112/05

   Summary of Contents for Philips AJ3112/05

  • Page 1 The Performer’s Protection Acts 1958 to 1972. English Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at CONTROLS (see fig. 1 ) 1 DISPLAY - shows the clock/ alarm time and status of the set...
  • Page 2: Specifications

    RADIO You can use this set solely as a radio! 1 Adjust RADIO / ALARM to RADIO ON to switch on the radio. 2 Select your waveband by adjusting the FM/MW switch. 3 Adjust TUNING to tune to your desired station. 4 Turn the VOLUME control to adjust the volume level.

This manual is also suitable for:


Comments to this Manuals

Symbols: 0
Latest comments: