Table of Contents
Advertisement
7
nstallation
I
Rubber seal
Hose connector
▶Water
supply
pressure
must
be between 30kPa and 1000kPa
(0.3~10kgf/cm2)
▶Don't
strip
or
crossthread when
connecting
Inlet hose
to
the valve.
▶If
the
water
supply
pressure is
more
than
1000kPa,
a
decompression
device should be installed.
?
Two rubber seals
are
supplied
with the water inlet hoses these
are
in order to
prevent
water
leaks.
?
Check
water
tightness
of
washing
machine connections
by
turning
the
tap
completely
on.
?
Periodically
check the condition of the hose and
replace
the hose
if necessary.
?
Make
sure
that there is
no
kink
on
the hose and that it is
not
crushed.
▶When
your washer has
two
valves.
?
The Inlet hose which has red
connector
is for the hot
water
tap.
?
If the washer has two
valves,
the energy is saved
by using
hot
valve.
Washing
Machine is
to
be connected
to
the
water
mains
using
new
hose-sets and that old
hose-sets should
not
be used.
Connecting
water
supply
hose
1. Do not
use an
extension cord
or
double
adapter.
2. If the
supply
cord is
damaged,
it must be
replaced by
the manufacturer
or
its service
agents
or
similarly qualified
person in order to avoid
a
hazard.
3.
Always unplug
the machine and
turn
off the
water
supply
after
use.
4.
Connect the machine
to
an
earthed socket in accordance with current
wiring regulations.
5. The
appliance
must be
positioned
so
that the
plug
is
easily
accessible.
?
Repairs
to the
washing
machine must
only
be carried out
qualified personnel. Repairs
carried out
by
inexperienced
persons may
cause
injury
or
serious
malfunctioning.
Contact your local service
center
?
Do not install your
washing
machine in
rooms
where
temperatures
below
freezing
may
occur.
Frozen hoses
may burst under pressure. The
reliability
of the electronic control
unit
may be
impaired
at
temperatures
below
freezing
point.
?
If the
appliance
is delivered in the winter months and
temperatures
are
below
freezing
:
Store the
washing
machine at
room
temperature
for
a
few hours before
putting
it into
operation.
Electrical
connection
CAUTION
concerning
the Power Cord
Most
appliances
recommend
they
be
placed
upon
a
dedicated
circuit;
that
is,
a
single
outlet circuit
which powers
only
that
appliance
and has
no
additional outlets
or
branch circuits. Check the
specification
page of this owner's manual
to
be certain.
Do
not
overload wall outlets. Overloaded wall
outlets,
loose
or
damaged
wall
outlets,
extension
cords,
frayed
power
cords,
or
damaged
or
cracked wire insulation
are
dangerous. Any
of these conditions
could result in electric shock
or
fire.
Periodically
examine the cord of your
appliance,
and if its
appearance indicates
damage
or
deterioration,
unplug
it,
discontinue
use
of the
appliance,
and have
the cord
replaced
with
an
exact
replacement
part
by
an
authorized servicer.
Protect the power cord from
physical
or
mechanical
abuse,
such
as
being
twisted, kinked,
pinched,
closed in
a
door,
or
walked upon.
Pay particular
attention
to
plugs,
wall
outlets,
and the
point
where
the cord exits the
appliance.
CAUTION
[WD(M)-16340(5)FD/
WD(M)-14340(5)FD/
WD(M)-12340(5)FD]
Rubber seal
Hose connector
Advertisement
Table of Contents
