Onkyo dr-635 dvd receiver instruction manual (36 pages)
Summary of Contents for Onkyo DR-S2.2
Page 1
COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE...
DR-S2.2 SPECIFICATIONS AMPLIFIER SECTION Power Output (FTC) All channels 40 watts per channel min. LINE (VIDEO 1, VIDEO 2/CDR/PC, TV/LINE, TAPE/MD/HD) RMS. into 6 ohms two channel driven, 200 mV/50 kohms 1,000 Hz with no more than 5 % total Composite (VIDEO 1, VIDEO 2/CDR/PC) 1 Vp-p, 75 ohms harmonic distortion.
DR-S2.2 SERVICE PROCEDURES-1 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs two lasers. Therefore, be sure to follow Laser Diode Properties carefully the instructions below when servicing. WARNING!! Wavelength: 650 nm SERVICE WARNING : DO NOT APPROACH THE Laser output: 0.6 mW...
Page 4
DR-S2.2 SERVICE PROCEDURES-2 SERVICE PROCEDURE 1. Replacing the fuses This symbol located near the fuse indicates that the fuse used is show operating type, For continued protection against fire hazard, replace with same type fuse , For fuse rating, refer to the marking adjest to the symbol.
Page 5
DR-S2.2 PC BOARD CONNECTION DIAGRAM AC IN P1701 P8004 E8102 E8101 +5VDSP E9991 U8603 U8602 U8601 E8601 P8601 TUNER UNIT JL8602A P8201A COMPONENT TERMIN NAVD-7441 DIGITAL TERMINAL Except UPP2P type PC BOARD P9992A NAETC-7442 ADCL AC-H AC-G AC-G AC-H P1801...
Page 6
DR-S2.2 COOLING FAN P1004 P1006 P1001 P1001 P3001 P3002 P3003 P4001 P1005 TV/LINE P1007 V2/CDR/PC TAPE/MD//HD VIDEO1 SWOUT ADCL ADCR AGND DACR DACL DACRS VIDEO PC BOARD RMINAL DACLS DACSW DACC NAVD-7439 AGND AGND P4006A MAIN PC BOARD NAAR-7428 P6501...
DR-S2.2 BLOCK DIAGRAMS Acoustic LEFT 5.1ch mode Control TV/LINE SWITCH VOLUME Rec SW RIGHT (DVD DSP) MUTE TAPE MUTE Q3001 BD3811K1 SUBWOOFER 50kHz LPF 5kHz LPF NAETC-7442 CS493292-CL AK4586 CRYSTAL D/A A/D DIGITAL SIGNAL PROCESSOR Converter VIDEO1 COAXIAL REMOTE MPD784225GC...
Page 8
DR-S2.2 UDD1N type only Except UDD1N NAAR-7428 FRONT FRONT LEFT LEFT SP B RELAY SP A RELAY FRONT FRONT FRONT SPEAKERS RIGHT RIGHT CENTER CENTER SURROUND LEFT LEFT SURROUND SURROUND SPEAKERS RIGHT NAAF-7510 RIGHT NAAF-7431 PHONES NAETC-7432 PHONES +15dB NAETC-7432...
Page 9
DR-S2.2 MICROPROCESSOR TERMINAL DESCRIPTION-1 Q8001: MPD784225GC-165-8BT PIN NAME ACTIVE DESCRIPTION TRAYIN Input pin of detected signal of tray state. No used (Connect to ground) No used (Connect to ground) No used (Connect to ground) No used (Open) DVDPOWER Output pin of control signal for power supply of DVD main circuit.
Page 10
DR-S2.2 MICROPROCESSOR TERMINAL DESCRIPTION-2 Q8001: MPD784225GC-165-8BT PIN NAME ACTIVE DESCRIPTION Output pin of serial data for PLL IC of tuner unit. PLLSDO Output pin of serial clock for PLL IC of tuner unit. PLLCLK Output pin of serial latch for PLL IC of tuner unit.
DR-S2.2 MICROPROCESSOR CONNECTION DIAGRAM-1 Q8001: MPD784225GC-165-8BT CENTER FRONT SPEAKER Switch which SPEAKER MAIN POWER detects insertion P7601 state of headphone TRANSFORMER RL5401 PHONES RL5402 T9991 AC IN 6ch volume with Detection circuit of Q9991 RL9991 SURROUND 8ch input selector speaker output level...
DR-S2.2 ADJUSTMENT PROCEDURES-1 TEST MODE FOR OPERATION 1. How to go in TEST MODE? [NOTE] All memories are cleared when you go in this mode. 1. Connect the power supply cord to a wall outlet. 2. Press POWER to switch on the main power to put the unit in the standby mode.
DR-S2.2 ADJUSTMENT PROCEDURES-2 OPERATION TEST-1 1. Speaker relays 1. Speaker relays turn ON approximately 5 seconds after STANDBY/ON is pressed. 2. Speaker relays turn OFF immediately after STANDBY/ON is pressed OFF. 2. DC detection circuit 1. Set the unit to "TEST-1-00." (Refer to TEST MODE OPERATION) 2.
DR-S2.2 ADJUSTMENT PROCEDURES-3 OPERATION TEST-2 7. The control voltage of AV connector (UPP type only) P1801 Language General 1. FSW voltage. Video1 AV CONNECTOR 1. Connect a dummyload, 10 kohms to No.8 pin of AV connector. TV Screen 4:3(Letter Box)
Page 15
DR-S2.2 ADJUSTMENT PROCEDURES-4 ADJUSTMENT OF DVD MECHANISM-1 1. Adjustment items and location Adjustment Items Tangential Radial [Mechanism Part] adjustment adjustment screw screw Tangential and Radial Height Coarse Adjustment DVD Jitter Adjustment How to initialize the Focus Sweep Setting [Electrical Part] Electrical adjustments are not required.
Page 16
DR-S2.2 ADJUSTMENT PROCEDURES-5 ADJUSTMENT OF DVD MECHANISM-2 4. Connection DIGITAL INPUT COMPONENT VIDEO OUTPUT REMOTE CONTROL DIGITAL VIDEO 2 VIDEO 1 ANTENNA 2 – –VIDEO – – 1 VIDEO 2 VIDEO 1 OUTPUT COAX VIDEO S VIDEO SURROUND CENTER FRONT SPEAKERS...
Page 17
DR-S2.2 ADJUSTMENT PROCEDURES-6 ADJUSTMENT OF DVD MECHANISM-3 TEST MODE: PLAY An address is displayed < When playback with the target address of disc (DVD)> For example, when playback with # 30000 During PLAY Press keys in order 030000 TEST MODE: OFF...
Page 18
DR-S2.2 ADJUSTMENT PROCEDURES-7 ADJUSTMENT OF DVD MECHANISM-4 DVD jitter Adjustment Preparation of adjustment Remove table(disc) in order to adjustment Tangential screw and Radial screw. Remove two screws. And remove clamper ass'y from mechanism. Lock clamper ass'y Remove four screws. And remove DVD Mechanism from chasis.
DR-S2.2 ADJUSTMENT PROCEDURES-8 ADJUSTMENT OF DVD MECHANISM-5 DVD jitter Adjustment After adjustment Move slider to the arrow direction. After you complete sdjustment attach Table(disc) in reverce procedure. Take care to re-assemble the procedure. The position of the gear Move slider to arrow.
Page 20
DR-S2.2 ADJUSTMENT PROCEDURES-9 ADJUSTMENT OF DVD MECHANISM-6 DVD Jitter Adjustment Playback method of inner and outer address for the purpose is refererd to "5. TEST MODE". Use disc: GGV1025 Test mode Play the DVD test disc at outer track (around #200000)
Page 21
DR-S2.2 ADJUSTMENT PROCEDURES-10 ADJUSTMENT OF DVD MECHANISM-7 Initialize the Focus Sweep Setting Purpose: To set the sweep which was correct with the individual Traverse mechanism. RC-484M CLEAR Monitor Memory Clear!!! PL Region : X1 ROM Vertion : 1.128 Note: Be sure to perform this step when replaced the Pickup or Traverse mechanism.
Page 22
DR-S2.2 ADJUSTMENT PROCEDURES-11 CHECK THE ERROR RATE Setting remote controller Press the hold down DVD button, then press 1 button. Check the CD error rate CD test disc Waiting for 8 seconds Play [Exanple] CD error rate = 33 / (7.35 x 5 x 1000) = 0.9 x 10 SPEC : CD error rate 3.26 x 10...
DR-S2.2 EXPLODED VIEWS OF MECHANISM DVD TRAY LOADING MECHANISM : DT1300 DT1300 Part No.24801014 PARTS LIST REF NO. PART NO. DESCRIPTION 70300470B LOADING MOTOR AS 70333502B PULLEY, GEAR 70342118 BELT 70333503C GEAR, LOADING 70333504D GEAR, CONNECTOR 70366204 TABLE DISK-B DVD...
Page 28
DR-S2.2 EXPLODED VIEWS OF MECHANISM TRAVERSE UNIT: DB-VTV301 (Torque : 0.12 0.01 N m) (Adjustment screw) (Adjustment (Torque : 0.12 0.01 N m) screw) Screw tight (Torque : 0.12 0.01 N m) The mechanical parts with no part number in the exploded views are not supplied.
DR-S2.2 SCHEMATIC DIAGRAMS-5 POWER SUPPLY SECTION NAPS-7429 +10V POWER C9994 Q9991 223Z DTC123J E9992 NAPS-7437 POWER SUPPLY PC BOARD SEC1A SEC1B D9923 R9929 1N4003 (1W) NAETC-7447 SEC2A D9921 RBV402 NAETC-7445 R9921 Q9921 F9921 78M56 SEC2B D9922 (1/2W) 115MA +10V SEC3A...
Page 38
DR-S2.2 POWER SUPPLY PC BOARD NPT-1358 R9993 13.9 D9992 22 (1/2W) T9992 POWER D9991 D9994 POWER SWITCH D9993 PC BOARD NASW-7430 23JS Except UDD1N, C9991 UDT3P,UDS4P Type NPT-1437 T9991 103M P9991 F9991 RL9991 AC IN E9991 UP TYPE UD TYPE...
Page 39
SCHEMATIC DIAGRAMS-6 VIDEO SECTION (UDD1N TYPE) NAVD-7439 VIDEO PC BOARD Q1001 C1001 VCC1 100/16 COPS.IN SQUE.SW C1004 LTER.SW COM_Y MUT1.SW Q1304 TC74HC4053AF C1005 C.IN 100/16 VCC 16 GND1 R1153 R1148 Y 15 Y1.IN X 14 YC_MIX.SW R1155 R1151 R1145 0 C1007 X1 13 SIG_IN.SW...
DR-S2.2 SCHEMATIC DIAGRAMS-9 DVD MAIN BOARD : DB-VPB303A / DB-VPB304 (1/4) (RF) RF IC IC101 LA9701M CN151 Wabble Detect Circuits 2/4,3/4 (RF) CN61 IC351 M56788AFP-TBB FTS DRIVER to NAETC-7435 P0005A CN51 to NAETC-7435 P0003A Page 43...
Page 44
DR-S2.2 (RF) : RF SIGNAL ROUTE : RF (VIDEO) SIGNAL ROUTE : RF (AUDIO) SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE : FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : SLIDER SERVO LOOP LINE IC201 LC78652W DSP IC...
Page 45
DR-S2.2 SCHEMATIC DIAGRAMS-10 DVD MAIN BOARD : DB-VPB303A / DB-VPB304 (2/4) PGM 8M FLASH MEMORY IC601 R607 6.8K FR CPU (MB91340) PD6345A Page 45...
Page 46
DR-S2.2 IC608 : AUDIO (DIGITAL) SIGNAL ROUTE IC612 CN401 To NAAR-7428 CN401 : Power supply Page 46...
Page 47
DR-S2.2 SCHEMATIC DIAGRAMS-11 DVD MAIN BOARD : DB-VPB303A / DB-VPB304 (3/4) IC712 (VD) IC701 BY CHIP PE5108A DVD Decoder Page 47...
Page 48
DR-S2.2 IC805 : RF (VIDEO) SIGNAL ROUTE (VD) : VIDEO DATA SIGNAL ROUTE (AD) : AUDIO DATASIGNAL ROUTE : AUDIO SIGNAL ROUTE : AUDIO (DIGITAL) SIGNAL ROUTE (VD) (VD) (VD) IC801 MITSUBISHI AV-1 M65774BFP MPEG2 Decoder Page 48...
Page 49
DR-S2.2 SCHEMATIC DIAGRAMS-12 DVD MAIN BOARD : DB-VPB303A / DB-VPB304 (4/4) VDB-VPB304 IC881 PM0026A Pro-1 (Cr) (VD) IC861 VIDEO ENCODER ADV7172KST (Cr) (Cb) (Cb) Page 49...
Page 50
DR-S2.2 (VD) : VIDEO DATASIGNAL ROUTE : V SIGNAL ROUTE : Y SIGNAL ROUTE : C SIGNAL ROUTE (Cr) : Cr SIGNAL ROUTE 304 Only (UDD1N type Only) : Y SIGNAL ROUTE (Cb) : Cb SIGNAL ROUTE : AUDIO SIGNAL ROUTE...
DR-S2.2 PRINTED CIRCUIT BOARD PARTS LIST-1 U1 MAIN PC BOARD NAAR-7428-1A/-1B/-1C/-1D NAME DESCRIPTION PART NO. REMARKS CIRCUIT NO. BD3811K1 22241761R3 Q3001 NJM4565M-D 22241383R2 Q3003, Q3012, Q3101, Q4002 PCM1742KE 22241776R2 Q4001 NJM4565M-D 22241383R2 STK402-950 222123 Power ampifier Q5001 AN7812F 222780124MAT Q9901...
Page 52
DR-S2.2 PRINTED CIRCUIT BOARD PARTS LIST-2 REMARKS CIRCUIT NO. NAME DESCRIPTION PART NO. C3063, C3064 Electric capacitor CE04W16V-47uF 354744709 354741009 C3101, C3108, C5601, C3103- C3105 Electric capacitor CE04W16V-10uF C4001, C4002, C4009, C4010 Electric capacitor CE04W16V-47uF 355744709 355741019 C4011, C4012 Electric capacitor...
Page 53
DR-S2.2 PRINTED CIRCUIT BOARD PARTS LIST-3 U2 POWER SUPPLY PC BOARD NAPS-7429-1A/-1B/-1C/-1D PART NO. REMARKS CIRCUIT NO. NAME DESCRIPTION Transistor 2213640 Q9991 Transistor DTC123JS Diodes D9991 - D9994 o Diode GP104003E or 22380035 or Diode RL1N4003 22380260 D9995 Chip diode...
Page 54
DR-S2.2 PRINTED CIRCUIT BOARD PARTS LIST-4 U4 SPEAKER TERMINAL PC BOARD NAAF-7431-1A/-1B/-1C/-1D (PP2P, PT3P, PA4P, GK3P, GR6P, DT3P Type only) NAME DESCRIPTION REMARKS CIRCUIT NO. PART NO. Transistors Transistor DTC123JS Q5401 - Q5403 2213640 Transistor DTA114ES Q5404, Q5405 2213510 Diodes...
Page 76
DR-S2.2 DISASSEMBLING PROCEDURES-1 REPLACEMENT OF POWER AMPLIFIER IC (Q5001) 1. Remove the screw. Remove the screws. 2. Disconnect wire. Rear Heat sink Remove the screw. Remove the screw. Rear Front Heat sink 1. Disconnect the wire. Remove two screws. 2. Remove DSP PC board ass'y (NADG-7452).
Page 77
DR-S2.2 DISASSEMBLING PROCEDURES-2 REPLACEMENT OF POWER AMPLIFIER IC (Q5001) Replacement power amplifier IC. Remove four screws. Power IC(Q5001) 1. Remove four screws. 2. Remove regurator PC board (NAETC-7449) Front NAETC-7449 Notes in assembly 1. Compander oil Apply compander oil between IC and heat sink.
Page 78
DR-S2.2 DISASSEMBLING PROCEDURES-3 DVD MECHANISM: DB-VTV301 / DT-1300 The laser diode in the optical pickup block is so sensitive to static electricity, surge current and etc. That the components are liable to be broken down or its reliability remarkably deteriorated.
Page 79
DR-S2.2 DISASSEMBLING PROCEDURES-4 DVD MECHANISM: DB-VTV301 / DT-1300 Remove DVD mechanism form Remove four screws. main chassis. Rotate the gear and move slider cam to Traverse unit arrow mark. slider cam gear Remove the screw. Notes at replacement flat cables Remove traverse unit from loading mechanism.
DR-S2.2 GENERAL INFORMATION DIAGNOSIS SELF-DIAGNOSTIC FUNCTION OF PICKUP DEFECTIVE This unit can confirm the laser diode current value (DVD: 650nm, CD: 780nm) of pickup on the Test Mode screen. (Press the RETURN SETUP keys in order on the test mode remote control unit (GGF1067) to enter the test mode.) It's effective in case of the following condition.
DR-S2.2 UPGRADE FIRMWARE-1 Prepares for upgrade firmware REMOTE CONTROLLER Monitor TV RC-484M Required to carry out check firmware Part No. 24140484 vertion and regeon cord. Required to carry out check firmware vertion and regeon cord. INTERFACE JIG INTERFACE JIG (KIT) Part No.
Page 82
DR-S2.2 UPGRADE FIRMWARE-2 Connections Rear panel view DIGITAL INPUT COMPONENT VIDEO OUTPUT DO NOT REMOTE CONTROL VIDEO 2 VIDEO 1 DIGITAL ANTENNA 2 – –VIDEO – – 1 VIDEO 2 VIDEO 1 OUTPUT connect the mains COAX VIDEO S VIDEO...
DR-S2.2 UPGRADE FIRMWARE-3 Flow chart In the case of replace of the DVD main board In the case of upgrade firmware Replace of the DVD main board Check the firmware Setting the regional code Download the firmware Except UDD1N type...
DRS-2.2 UPGRADE FIRMWARE-4 Check the firmware Please operate it by remote controller (RC-484M). 1. Press the DVD button. 2. Press SETUP button. 3. Operate cursor button and select General menu. Refer to 4. Operate cursor button and select Setup Menu mode. Refer to Refer to 5.
Page 85
DR-S2.2 UPGRADE FIRMWARE-5 Download firmware [NOTES] This procedure document supposing using Japanese PC. The program file name, the folder name, etc. are examples. 1. Start MS-DOS prompt using the start-up menu of PC. Windows of MS DOS prompt C: WINDOWS>_ 2.
DR-S2.2 UPGRADE FIRMWARE-6 Download procedures 5. Check that the connection of PC with DR-S2.2. 6. Check that unit is in the state of NO DISC. 7. Turn ON the power supply switch of the unit. 8. Press the Enter key of PC.
Page 87
DR-S2.2 UPGRADE FIRMWARE-7 Download procedures State witch download completed The state which download completed The work of download was completed satisfactory. Page 87...
Page 88
UPA4P UDS4P UGR6P FL display NO DISC 3. Turn OFF power of DR-S2.2. 4. Disconnect DR-S2.2 and the PC. Chack firmware and regional cord You check whether it is set up firmware and repional cord correctly. Refer to about check procedure.