La Crosse Technology WS6826 Quick Setup Manual

Wireless Color Forecast Station
WS6826 | Quick Setup Guide
The Wireless Color Forecast Station features manual set time, date,
weather forecast, indoor and outdoor temperature/humidity, with
temperature alerts, and heat index and dew point, on a stylish, colorful,
and easy to read display. Use the integrated USB charging port to
charge your smartphone, camera or other device when the forecast
station operates on A/C power. Wireless transmission range of over 300
feet (90 meters) in open air, from transmitter to forecast station.
WIRELESS COLOR FORECAST STATION
THIS STATION LEARNS
Please allow 3-4 days for barometer calibration to generate an
accurate forecast.
SETUP INSTRUCTIONS STEP BY STEP
STEP 1:
• Insert the 5-volt A/C power adapter into the designated area on the
back of the forecast station.
• Plug the A/C power adapter into a wall outlet for continuous backlight
(ON/OFF), and dimmer feature.
STEP 2: (optional battery operation)
• Remove battery cover from the forecast
station: Slide tab down and pull out to remove the cover.
• Insert 3 NEW AAA batteries (not included) into the back of the
forecast station. Observe the correct polarity (see marking inside the
battery compartment).
• The forecast station will light up and show, indoor temperature,
humidity and time.
• (Press and release the HI/LOW/OFF button to illuminate the backlight
for 8 seconds when using only battery power.)
•
Do Not Mix Old and New Batteries
• Do Not Mix Alkaline, Standard, Lithium or Rechargeable
Batteries
STEP 3:
• Ensure that the transmitter is within 10 feet of the forecast station.
• Remove battery cover from transmitter: Slide the battery cover down
and lift off the front.
• Insert 2 NEW AA batteries (not included) into the
transmitter. Observe the correct polarity.
• Within 3 minutes, the forecast station will show
readings in the Outdoor temperature area on the LCD.
Note: Use Alkaline batteries (or Lithium for temperatures
below - 20°F /-28.8°C).
TRANSMITTER SIGNAL STRENGTH
After the batteries are inserted, the forecast station will search for the
outdoor temperature/humidity transmitter for 3 minutes.
The antenna symbol will flash during reception, and temperature
display will be dashes "---".
The antenna symbol will scroll during transmitter synchronization.
If synchronization fails once, the antenna will lose one bar.
If synchronization fails twice, the antenna will lose two bars.
If reception continuously fails to receive 5 times, the antenna symbol
will be shown as .
The antenna will show full display with successful RF
(radio frequency) reception.
TROUBLESHOOTING
If the outdoor temperature is not displayed after three
minutes, hold the SENSOR SEARCH button on the
forecast station for three seconds to search for
outdoor transmitter.
Next, remove the battery cover from the transmitter then press the TX
button to send a signal.
If it still does not receive the outdoor temperature, remove the A/C
cord and batteries from both the forecast station and the transmitter
for 15 minutes repeat setup instructions from step 1.
TIME/DATE
The SETTINGS button moves through the program menu
and confirm settings.
Use the UP ARROW button to increase a value.
Use the DOWN ARROW button to decrease a value.
SET TIME/DATE
Hold the SETTINGS button for three seconds to enter time set mode.
LANGUAGE : The language will flash. Use the ARROW buttons to
select the language for weekday display (French, Italian, Dutch,
Spanish, Danish, English or German) and press the SETTINGS
button to confirm and move to 12/24 hour.
12/24-HOUR: The time format will flash. Use the ARROW buttons to
choose 12-hour or 24-hour time format and press the SETTINGS
button to confirm and move to hour.
HOUR: The Hour will flash. Use the ARROW buttons to choose the
hour, and press the SETTINGS button to confirm and move to
minutes.
MINUTES: The Minutes will flash. Use the ARROW buttons to
choose the minutes, and press the SETTINGS button to confirm and
move to the year.
YEAR: The Year will flash. Use the ARROW buttons to choose the
year, and press the SETTINGS button to confirm and move to the
month.
MONTH: The Month will flash. Use the ARROW buttons to choose
the month, and press the SETTINGS button to confirm and move to
the date.
DATE: The Date will flash. Use the ARROW buttons to choose the
date, and press the SETTINGS button to confirm and move to
Fahrenheit/Celsius.
FAHRENHEIT/CELSIUS: °F or °C will flash. Use the ARROW buttons
to select Fahrenheit or Celsius. Press and release the SETTINGS
button to confirm and exit the program menu.
Note: When no buttons are pressed for ten seconds, the forecast station
will save the last change and default back to normal time and
temperature display mode.
ALARM TIME
The TIME ALARM button moves through the alarm
set mode and confirms settings.
Use the UP ARROW button to increase a value.
1