Table of Contents
Advertisement
en
If the advice given does not resolve your
problem, please contact your customer
service. Contact details can be found on
the back cover of this instruction manual
or in the enclosed customer service list.
When calling , please quote the appliance
number (1) and the production date
(FD
=
_g}_which can be found on the rating
plate
~
on the appliance door.
2
!
Rely on the expertise of the
manufacturer. Call us to ensure that the
repair will be carried out by fully-trained
service engineers, who are equipped with
original spare parts for your appliance.
22
The dishwasher must be connected
correctly, otherwise it will not function
properly. The specifications for the inlet
and outlet as well as the electrical
connected loads must correspond with the
required criteria as specified in the
following paragraphs or in the installation
instructions.
Install the appliance in the correct
sequence:
-
Checking appliance on delivery
-
Installing the appliance
-
Waste water connection
-
Fresh water connection
-
Electrical connection
Safety instructions
-
Install and connect the appliance
according to the installation and
assembly instructions.
Prior to installation, disconnect the
dishwasher from the power supply.
Ensure that the protective conductor
system of the domestic supply has
been correctly installed.
The electrical connection conditions
must correspond with the
specifications on the dishwasher rating
plate
1331.
If the power cord of this appliance is
damaged, it must be replaced with a
particular power cord.
To prevent injury, the power cord may
be replaced by customer service only.
If the dishwasher is installed in a high-
sided unit, the unit must be secured
properly.
Install built-under or integratable
appliances only under continuous
worktops which have been screwed to
adjacent cupboards to ensure stability.
Do not install the appliance near heat
sources (radiators, heat storage tanks,
cookers or other appliances which
generate heat) and do not install under
a hob.
To ensure good washing results, the
dishwasher requires soft water, i.e.
containing low amounts of lime, otherwise
white limescale will be deposited on the
utensils and inner container.
Ta,I? water above
go
Clarke (from set value
H:u I)
must be softened. The water is
softened with salt (regeneration salt) in the
water softening system of the dishwasher.
The setting and therefore the required
amount of salt depends on the degree of
hardness of your tap water (see table).
Setting
The amount of salt dispensed can be
set in 4 stages
depending on the hardness of your water.
Accordingly 0, 1, 2 or 3 displays are lit
(see table).
-
Find out about the hardness
value of your tap water. Your water
utility company will help you with this.
-
Setting can be found in the water
hardness table.
-
Close the door.
Water hardness table
Water
hardness
value adH
I
Hardness
I
range
mmol/1
I
Setting
en
-
Rotate the programme selector [ ] ]
from the 12 o'clock position anti-
clockwise by one notch.
~
-
Switch on main switch
[I]
and hold
down for at least
3
sec.
The salt refill indicator
W
flashes
and the lamps above the symbols
.ia
and
ITITl
light up. (Hardness value has
been set to 2 at the factory.)
To change the setting:
-
Rotate programme selector
W.
You can select a set value between 0
and 3 according
to the hardness of your water.
If the lamps
.ia,
ITITl
and "End" light up,
the maximum set hardness value has
been reached. If the programme
selector is turned further, the lights go
out and the set hardness value is set to
level 0.
-
Switch off the main switch
CIJ.
The chosen setting has now been
stored.
0
0
0
...
TTTTI
End
0
0
0
•
0
0
• •
0
• • •
7
Advertisement
Table of Contents
