1. Manuals
  2. Brands
  3. Stealth Manuals
  4. Welding System
  5. DIGI-CUT 60-1
  6. Operator's manual

Stealth DIGI-CUT 60-1 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

DIGI-CUT 60-1
Part No. 9031H
OPERATOR'S
MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DIGI-CUT 60-1 and is the answer not in the manual?

Questions and answers

Related Manuals for Stealth DIGI-CUT 60-1

Summary of Contents for Stealth DIGI-CUT 60-1

  • Page 1 DIGI-CUT 60-1 Part No. 9031H OPERATOR’S MANUAL...
  • Page 2 STEALTH DIGI-CUT 60-1 IMPORTANT Read this Owner’s Manual completely before attempting to use this equipment. Save this manual and keep it handy for quick reference. Pay particular attention to the safety instructions provided for your protection. Contact your distributor if...

  • Page 3: Table Of Contents

    STEALTH DIGI-CUT 60-1 CONTENTS SAFETY TECHNICAL INFORMATION INSTALLATION OPERATION CONTROL AND CONNECTORS MAINTENANCE TROUBLESHOOTING MAIN ELECTRICAL DIAGRAM...

  • Page 4: Safety

    OPERATION AND MAINTENANCE OF PLASMA ARC EQUIPMENT CA of cardiac pacemakers, hearing aids, or other electronic health equipment. Persons who work ne STEALTH DIGI-CUT 60-1 applications should consult their medical health professional and the manufacturer of the health HAZ- ARDOUS TO YOUR HEALTH.
  • Page 5 FIRE AND EXPLOSION must be protected. • Extra care must be taken when the workplace is moist or damp. STEALTH DIGI-CUT 60-1 • Ventilate all flammable or explosive vapors from the workplace. • Disconnect power source before performing any service or repairs.

  • Page 6: Technical Information

      STEALTH DIGI-CUT 60-1 2. TECHNICAL INFORMATION §2 Technology Parameters Main circuit functions 2.1 Working principle of main circuit The working principle of DIGI-CUT 60 is shown as the following figure. Three-phase The working principle of CUT 60-1 Air Plasma Cutting Machine is shown as the following figure. Single-phase 380V work frequency AC is rectified into DC (about 530V), then it is converted to medium frequency AC (about 20 KHz) by the inverter device (discrete IGBT).
  • Page 7 STEALTH DIGI-CUT 60-1 DIGI-CUT 60 Power Supply Voltage (V) 1-220/230/240V±10% Frequency Hz 50/60 Rated input current (A) Rated input power (Kw) Adjustment range of current (A) 20~60 Max no-load voltage (V) 95% 60A Duty cycle (40ºC / 10 minutes) 100% 58A Severance Cut for Carbon Steel (mm) ≤35...

  • Page 8: Installation

    STEALTH DIGI-CUT 60-1   3. INSTALLATION §3 Installation Unpacking 3. 1 Unpacking Use the packing lists to identify and account for each item. Use the packing lists to identify and account for each item. 3.1.1 Inspect each item for possible shipping damage. If damage is evident, contact Inspect each item for possible shipping damage.

  • Page 9: Operation Control And Connectors

    §4 Operation STEALTH DIGI-CUT 60-1 4.1 Layout Of The Front And Rear Panel 4. OPERATION CONTROL AND CONNECTORS         power pilot lamp: turn on power, the lamp on. 1. Cutting current regulator – used to regulate the current when cutting.

  • Page 10: Cutting Operation

    STEALTH DIGI-CUT 60-1 Cutting Preparation 4.2 Cutting Preparation 4.2.1 Tightly connect the power cable to an electrical socket outlet ( refer to the Input Voltage in section 2 Technology Parameters). 1、Tightly connect the power cable to electrical socket outlet (the input voltage, refer to the s 4.2.2 Connect the air pipe to the air supply equipment and the earth cable to the...

  • Page 11: Maintenance

    §5 Maintenance STEALTH DIGI-CUT 60-1 5.1 Cutting gun maintenance 5. MAINTENANCE Warning : 1. Check the consumable parts for damage, if worn, replace it. Cutting Gun 2. Turn off the power source before check or remove cutting gun parts WARNING 1. Check consumable parts for damage and replace if worn.

  • Page 12: Troubleshooting

    STEALTH DIGI-CUT 60-1 TROUBLESHOOTING WARNING There are extremely dangerous voltage and power levels present inside this unit. Do not attempt to diagnose or repair unless you have had training in power electronics measurement and troubleshooting techniques. 6.1 Power lamp and temperature lamp is on.
  • Page 13 STEALTH DIGI-CUT 60-1 Arc shuts off during operation. Arc will not restart when torch switch is activated. 6.6.1 Power Supply is overheated (OC/OT lamp is lit) – allow unit to cool down for at least 5 minutes. Make sure the unit has not been operated beyond Duty Cycle limit.

  • Page 14: Main Electrical Diagram

      STEALTH DIGI-CUT 60-1 Electrical principle drawing MAIN ELECTRICAL DIAGRAM  ...
  • Page 15 STEALTH DIGI-CUT 60-1...
  • Page 16 STEALTH DIGI-CUT 60-1...

Table of Contents