Advertisement
PARTS LIST PTZ-600
REF. NR.
DESCRIPTION
1
FIXED SHEET
2
GUIDE
3
KNOB
5 TILL 7
UPPER SAFEGUARD COMPLETE
10
RIVING KNIFE
13
FOOT
16
KNOB
24+25
LOWER SAFEGUARD WITH COVER
28
WATER TANK
29
INNER FLANGE
30
DIAMOND CUTTING DISC 180X22,2X2,2
31
OUTER FLANGE
32
NUT
33
ANGLE GUIDE
34
SWITCH
6
PC
407101
TILE CUTTER
407102
407455
THE NUMBERS IN THE FOLLOWING TEXT
407103
CORRESPOND WITH THE PICTURES AT PAGE 2.
407104
TECHNICAL SPECIFICATIONS
407105
407456
Voltage
407106
Frequency
Power consumption
407107
407108
No load speed
TCA1004
Max. depth of cut 90º
Max. depth of cut 45º
407109
Cutting angle
407110
Ø Cutting blade
407111
Table dimensions
Lpa (sound pressure level)
407112
Lwa (sound power level)
Vibration
CONTENT OF THE BOX
1 Tile cutter
1 Water tray
1 Full-length adjustable fence
1 Mitre guide
1 Set of instructions
1 Safety instructions
1 Guarantee card
SAFETY INSTRUCTIONS
The following symbols are used in these instructions for
use:
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
ELECTRICAL SAFETY
When using electric tools, basic safety precautions
should always be followed to reduce the risk of fire,
electric shock and personal injury. Read all these
instructions before attempting to operate this product
and save these instructions.
Powercraft
Powercraft
| 230 V~
| 50 Hz
| 600 W
| S2= 30 min
| 2,800/min
| 35mm
| 20mm
| 0 - 45°
| 180x22.2x2.2mm
| 360 x 330mm
| 63.08 dB(A)
| 76.08 dB(A)
| 1.34 m/s
2
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
Always check that the voltage corresponds to the
voltage on the rating plate.
REPLACING CABLES OR PLUGS
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
SAFETY MEASURES
•
Check your powertool for damage before starting
your work, particularly the diamond blade. All parts
must be fitted properly and must meet all
requirements in order to guarantee the tool's
smooth operation. Any safety guards or any lightly
damaged parts must be checked to see if they still
function properly before continuing the use of the
tool. Moving parts, and the diamond-blade guard in
particular, must be fitted properly and must not jam.
Do not use tools that cannot be switched on or off
with the switch.
•
The diamond-blade guard must not be jammed or
removed.
•
A jamming guard must be repaired immediately.
•
The riving knife must not be removed.
USE
This tool is suitable for cutting various wall and floor tiles
with a maximum tile size of 500 x 500 x 35mm. The
diamond wheel can be replaced by the customer. It is not
permitted to use the tool for any other materials.
ASSEMBLY
Fig.1
1. Mounting the riving knife
•
Unscrew the two (crosshead) screws (9) and place
the foot of the riving knife (10) under the table
•
Place the small plate (2 holes with thread) under the
foot of the riving knife
•
Connect the riving knife with the two screws and the
plate
2. Mounting the saw blade
•
Unscrew two screws out of lower blade guard and
remove the guard
•
Dismount nut (counterclockwise) and outer flange
•
Place blade on the inner flange
•
Mount outer flange and nut (clockwise) again
•
Place the lower blade guard back in position and
connect the two screws
3. Mounting the upper blade guard (11)
•
Slide the guard in horizontal position across the
riving knife.
•
Connect the guard to the riving knife with the bolt
(12) and the locknut
•
Be aware that the guard is connected under the lock-
pin (13). The lock-pin prevents the guard falling
backwards.
3
Advertisement
