Related Manuals for Electrolux LAVAMAT 70030
Summary of Contents for Electrolux LAVAMAT 70030
-
Page 1: Service Manual
SERVICE MANUAL WASHING Frontloading Washing machines EWM 2000+ 599 50 07-53/0 TSE - N Ausgabe:01.2000 Edition: 01.2000 TSE-N 01.2000 R.K. 599 50 07-53/0 - 1 -... - Page 2 II. LAVAMAT 70030 1. Operating elements / panel 1.1 One button - Input philosophy 1.2 Programe selection switch 2. Additional programes 2.1 Gentle spin 2.2 Spinning 2.3 FUCS fast unbalanced control system 2.3.1 Function of FUCS 2.4 Pumping 2.5 Starching 2.6 Delicate rinse...
- Page 3 II. LAVAMAT 70030 6. Cool down 7. Aqua - Control - System 7.1 General Function 7.2 Floating switch 8. The pressure sensor 8.1 Function of the pressure sensor 9. Automatic foot 10. Service - Program 10.1 Activate Service - Program 10.2 Fault indication in the multidisplay...
-
Page 4: Characteristics ( Features )
ÖKO_LAVAMAT 70030 UPDATE Characteristics ( features ) Electronic machine Sensortronic foam detection Fast unbalance control system FUCS Motor is phase cutting controlled Jet - System Carbon tube Updatefunction Maximal number of drum revolution 1600 1/min Handlaundry program Easy Iron Top class machines with automatic foot TSE-N 01.2000 R.K. - Page 5 Machine classes TSE-N 01.2000 R.K. - 5 - 599 50 07-53/0...
- Page 6 Indication of several models ⇓ ⇓ ⇓ ⇓ ⇓ ⇒ ⇓ ⇓ ⇓ ⇓ ⇒ ⇓ ⇓ ⇓ ⇒ ⇓ ⇓ ⇒ ≤ ⇓ ⇒ TSE-N 01.2000 R.K. - 6 - 599 50 07-53/0...
-
Page 7: Operating Elements / Panel
1. Operating elements / panel 1.1 One button - Input philosophy Every washing programe with its temperature can be adjusted with the programe selection switch. Door Option buttons Spin speed Program cycle Program adjusting Start / Pause Multidisplay Variants without multidisplay have 8 LED’s in the program cycle display. The LED „Pump“ is added. -
Page 8: Additional Programes
2. Additional programes 2.1 Gentle spin Select with programe selection switch Programe time 4 min.; speed 600 1/min „Gentle spin“: (IMP_C0 Page 34 ) same as delicate spin at 700 1/min 2.2 Spinning Select with programe selection switch Programe time 8 min.; speed maximum „Spinning“: ( IMPCF_01_AC Page 33 ) same as cotton / linen final spin 2.3 Fast unbalanced control system FUCS... - Page 9 2. Additional programes 2.3.1 Function of FUCS Duration and limit table: Phase Speed start Speed end Time (duration) Unbalanced load limits 55 1/min 115 1/min from 0 to 200 sec Time out 1 1,280 55 1/min 115 1/min from 0 to 140 sec 1,280 from 140 to 155 sec 1,760...
- Page 10 2. Additional programes 2.4 Pumping Select with programe selection switch position „Pumping“ Programe time 3 min. Pumping until switching point of the pressure switch (Foam level) additional 120 sec. fixed pumping time 2.5 Starching Select with programe selection switch position „Starching“ Programe time 23 min.
- Page 11 3. Option buttons / display 3.2 Soaking - No prewash can be chosen - for dried, encrusted stains - If you chose handlaundry with soaking it is not possible because this funktion is locked - soaking with a temperature max. 30°C possible - Different washmechanics.
- Page 12 3. Option buttons / display 3.4 Stain - Available for cotton, easy care and delicate with a chosen temperature greater or equal the 40° - Load spot powder into the stain compartment of the drawer - Spot powder intake after the 40° bio phase - Program time extention of 10 min.
-
Page 13: Multi Display
3. Option buttons / display 3.6 Start / Pause - It starts the machine after the options and the desired cycle is selected. - Pressing the start / Pause button during a cycle, the program stops and the start/pause LED blinks. The locking condition decides, if the machine can be opened. -
Page 14: The Intelligent Doorlock
3. Option buttons / display 3.8 Electronik cycle display - indicates the selected programe steps - indicates the actual steps during the programe - indicates the end of programe - indicates at the end of programe „Overdosage“ that means to much detergent is used. The LED is only illuminated if foam is detected during the first intermidiate spin. -
Page 15: Additional Features
Additional features More water switch The function of the more water switch must now be programmed with the in/output electronic . This has to be done before a programe is started. The extra rinse will be inserted in all programes except wool. The cool down setting is not available it’s excecuted, if the chosen temperature is >... -
Page 16: Easy Iron
Easy iron - You can find the programe easy iron in the programe block easy care. - Temperature 40°C; Load 1Kg - The mainwash is the same as by easy care, The movement of the motor is 2 minutes extended - The rinse cycles are the same as by easy care No intermidiate spin - Automatic cool down about 8L... - Page 17 Water intake system Waterdistributer + Valve 4 - Way Waterdistributer mechanically moved 3 - Valves Drawer Compartment for prewash powder/soaking powder or water softener Will be taken in at the very beginning of the program Active valve: S1 Compartment for the main wash powder. Will be taken in at the beginning of the main wash.
- Page 18 5.3.1 Water scheme 4 detergent chambers; recirculation pump and drain pump 4 - Way Waterdistributer mechanically moved 3 - Valves TSE-N 01.2000 R.K. - 18 - 599 50 07-53/0...
- Page 19 Water intake diagrames 5.3.1 Water intake diagram cotton linen without any options chosen. Waterintake depends on the kind of laundry and the soakingability! No Fuzzy logic measurements in this machine. TSE-N 01.2000 R.K. - 19 - 599 50 07-53/0...
- Page 20 Definition Rinsing SPMFF Rinse with free water The machine excecutes a maximum of 4 rinses This rinse techcnology has no disadvantage, because the recirculation system guaranties the rinse result. The last range of washing machines had the same amount of water and needed therfore more rinse cycles (SPOFF), because the free water couldn’t be used.
- Page 21 Definition rinsing 5.4.1 The principle rinse technology Gradual increasing of the water used at the rinse cycle and the intermidiate spin. Mainwash Rinse 1 Rinse 2 Rinse 3 after final spin rinse water Soaked water after the rinse cycle and its remaining alkalinity.
-
Page 22: First Rinse
First rinse Cotton / linen virtual rinse: filling up to TAB_ rinse level (bleach chamber) about 9L if load 5 kg depending on pressure sensor (Soakingability and load) circulation pump on movement E_MOV 3 sec off 10 sec on 55 1/min movement E1_MOV 4 sec off 12 sec on 75 1/min If the pressure sensor detects a level below the TAB_rinse level, following steps are excecuted:... -
Page 23: Additional Rinse
Additional rinse Cotton / linen, easy care and delicate traditionell rinse: Filling over bleaching chamber ( RII_level) about. 13L with 5 Kg Movement D_MOV 12sec off 4 sec on 55 1/min Without recirculation pump Second rinse Cotton / linen virtual rinse: filling up to TAB_ rinse level (bleach chamber) about 9L if load 5 kg depending on pressure sensor (Soakingability and load) circulation pump on... -
Page 24: Softening Rinse
Softening rinse Cotton / linen traditionell rinse: Filling over softener chamber ( RII_level) about 13L if load 5 Kg Depending on pressure sensor. (Soakingability and load) Movement N_MOV 8sec off 8 sec on 55 1/min Without recirculation pump Easy care traditionell rinse: Filling up to High_level (softener chamber) about 12L if load 2,5 kg and recirculation pump is on. -
Page 25: Aqua Control System
Aqua Control System General construction Safty hose with a „normal“ pressure hose inside, without integrated electrical connection between the machine and the water tab valve. Hose system is all around closed and watertight At the water tab is a „mechanic“ safty valve without electric connection The hose is connected at the water inlet valve In case of a fault, that means the inner hose is leaking, a sponge as a part of the mechanic safty valve expands and closes the valve at the water tab. -
Page 26: The Pressure Sensor
The pressure sensor Air inlet Membrane Coil Oscillator ( Elektronic ) Magnetic ring Spring Screw to adjust Connector Function of the analog sensor Over the air inlet the water pressure moves the membrane. The membrane moves the magnetic ring (5) into the coil (3). Then the oscillator puts an other frequency on the main electronic. -
Page 27: Service Program
Service - Program 10.1 Activate Service - Program Switch the machine off. Keep the prewash and soaking button depressed and turn the rotary switch to the position cotton linen 95°C. Keep the prewash and soaking button depressed until the LED’s are illuminated. Clear the fault memory To clear the fault memory access the configuration program. - Page 28 Service - Programm 10.2 Fault indication in the multidisplay. TSE-N 01.2000 R.K. - 28 - 599 50 07-53/0...
- Page 29 Service - Programm 10.2 Fault indication in the multidisplay. TSE-N 01.2000 R.K. - 29 - 599 50 07-53/0...
- Page 30 Service - Programm 10.2 Fault indication in the multidisplay. Machines without multidisplay show the faultcodes with the program cycle LED’s. In this case you have to take care about the values of the single LED’s. LED Off LED On If fault E40 is shown the LED mainwash will be blinking. If faultcode E93 is shown, Prewash, Rinse+, End und Overdosage blinks.
- Page 31 10. Service - Programm 10.3The configuration - Program Activate service - program Turn the rotary switch clockwise to the position delicate spin. If the mainelectronic has to be changed you have to configurate the spare part electronic A code with 16 digits has to be stored. This code sets the variante of the machine. Caution: Don’t use the LED’s to configurate if there is a multidisplay, because this variante has 7 LED’s.
- Page 32 10. Service - Programm 10.3The configuration program Configuration code: You can find the configuration code on a sticker, which is located on the electronic housing. Also in the spare part list the code is shown. It is very important to remark this code on the new elctronic housing.
- Page 33 11. Spinning profiles 11.1 For the program cotton linen 1. Intermidiate spin 2. und 3. Intermidiate spin Final spin TSE-N 01.2000 R.K. - 33 - 599 50 07-53/0...
- Page 34 11. Spinning profiles 11.2 For the program easy care 1. Intermidiste spin is not excecuted 2. Intermidiate spin 3. Intermidiate is not excecuted The final spin TSE-N 01.2000 R.K. - 34 - 599 50 07-53/0...
- Page 35 11. Spinning profiles 11.3 For the program delicate wash No intermidiate spins are excecuted! The final spin 11.4 For the Handlaundry program No intermidiate spins are excecuted! The final spin TSE-N 01.2000 R.K. - 35 - 599 50 07-53/0...
- Page 36 Technic 12.1 Wiring plan TSE-N 01.2000 R.K. - 36 - 599 50 07-53/0...
-
Page 37: Circuit Diagram
12.2 Circuit diagram TSE-N 01.2000 R.K. - 37 - 599 50 07-53/0... - Page 38 12.3 Legend TSE-N 01.2000 R.K. - 38 - 599 50 07-53/0...
- Page 39 12.4 Function plans TSE-N 01.2000 R.K. - 39 - 599 50 07-53/0...
- Page 40 12.4 Function plans TSE-N 01.2000 R.K. - 40 - 599 50 07-53/0...