Philips 40PFL4707/F7 Service Manual
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. LCD TV
  5. 40PFL4707/F7
  6. Service manual

Philips 40PFL4707/F7 Service Manual

40"
Hide thumbs Also See for 40PFL4707/F7:
Table of Contents

Advertisement

Quick Links

See also: User Manual

Service Manual

TYPE A
40PFL4707/F7
40PFL4707/F8
40PFL4907/F7
This service manual contains information of different types of models.
This service manual contains information of different types of models.
Make sure to refer to the section describing your model.
Make sure to refer to the section describing your model.
© 2012 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
PHILIPS
(Serial No.: DS1)
PHILIPS
(Serial No.: XA1)
PHILIPS
(Serial No.: DS1)
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
chassis PL12.3

Contents

40" LCD TV
120329

Advertisement

Table of Contents
loading

Related Manuals for Philips 40PFL4707/F7

Summary of Contents for Philips 40PFL4707/F7

  • Page 1: Service Manual

    40” LCD TV chassis PL12.3 Service Manual Contents TYPE A 40PFL4707/F7 PHILIPS (Serial No.: DS1) 40PFL4707/F8 PHILIPS (Serial No.: XA1) TYPE B 40PFL4907/F7 PHILIPS (Serial No.: DS1) This service manual contains information of different types of models. This service manual contains information of different types of models.

  • Page 2: Important Safety Notice

    IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Specifications ................1-1 Important Safety Precautions .

  • Page 4: Specifications

    SPECIFICATIONS < TUNER / NTSC > ANT. Input ---------------------- 75 Ω Unbal., F type Description Condition Unit Nominal Limit 1. AFT Pull-In Range ±2.3 ±2.1 TV.ch.4 dBµ 2. Synchronizing Sens. CA.ch.31 dBµ CA.ch.87 dBµ < TUNER / ATSC > Description Condition Unit Nominal...

  • Page 5: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
  • Page 6 3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
  • Page 7 Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
  • Page 8 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.

  • Page 9: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: Top View 1. Prepare the hot-air flat pack-IC desoldering Bottom View machine, then apply hot air to the Flat Pack-IC Input...
  • Page 10 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
  • Page 11 2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
  • Page 12 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

  • Page 13: Cabinet Disassembly Instructions

    CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Step/ Fig. Loc. Part Removal Note This flowchart indicates the disassembly steps for the cabinet parts and the CBA in order to gain access to Speaker items to be serviced. When reassembling, follow the D3 2(S-10) Holder(L,R) steps in reverse order.
  • Page 14 (L-1) (L-1) (S-3) (S-2) (L-1) (S-2) (S-2) (S-4) (S-5) (L-1) (S-2) (S-3) (S-2) (S-1) (S-3) [2] Rear Cabinet (S-2) [1] Stand Assembly Fig. D1 PL12.3_DC...
  • Page 15 TYPE A (S-6) Jack Holder TYPE B (S-7) (S-6) [3] Digital Main CBA Unit Wireless Adaptor (S-7) CL600 Jack Holder [4] Power Supply CBA Fig. D2 PL12.3_DC...
  • Page 16 [7] Power PCB Holder (S-9) [6] Digital PCB Holder (S-9) (S-9) (S-9) Wire Holder (S-8) [9] Speaker Holder R CL600 [10] Stand Bracket (S-10) (S-11) (S-11) (S-12) [8] Speaker Shield Plate [5] IR Sensor CBA (S-10) [9] Speaker Holder L [8] Speaker Fig.
  • Page 17 [13] Front Cabinet Panel Holder T Corner Block Panel Holder R (S-13) (S-13) [12] LCD Module Assembly Panel Holder L (S-13) Knob Frame [11] Function CBA Function Button Fig. D4 PL12.3_DC...
  • Page 18 TV Cable Wiring Diagram To LCD Module To LCD Module Assembly Assembly Digital Main Power Supply CBA CBA Unit CN401 CN3013 CN3906 Function CN3701 CN3601 CN501 CN600 CN3801 CN3101 To AC Inlet *1: TYPE A CN3105 *2: TYPE B CN4001 To Speaker IR Sensor CBA CN4051...

  • Page 19: Electrical Adjustment Instructions [Type A]

    ELECTRICAL ADJUSTMENT INSTRUCTIONS [TYPE A] General Note: “CBA” is abbreviation for 1. Purity Check Mode “Circuit Board Assembly.” This mode cycles through full-screen displays of red, Note: Electrical adjustments are required after green, blue, and white to check for non-active pixels. replacing circuit components and certain 1.

  • Page 20: White Balance Adjustment

    The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal appears in the screen. (“Internal (Single)” appears performed when replacing the LCD Panel in the upper right of the screen as shown below.) or Digital Main CBA. 2.

  • Page 21: Type B]

    [TYPE B] General Note: “CBA” is abbreviation for 1. Purity Check Mode “Circuit Board Assembly.” This mode cycles through full-screen displays of red, Note: Electrical adjustments are required after green, blue, and white to check for non-active pixels. replacing circuit components and certain 1.
  • Page 22 The White Balance Adjustment should be 5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.) performed when replacing the LCD Panel 6. Press [MENU] button. The internal Raster signal or Digital Main CBA. appears in the screen.
  • Page 23 13. Press [9] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature. Internal (Single) 14. Press [7] button to select the “LDR” for Low Drive Red adjustment (“LDR”...

  • Page 24: How To Initialize The Lcd Tv

    HOW TO INITIALIZE THE LCD TV The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure.

  • Page 25: Firmware Renewal Mode

    FIRMWARE RENEWAL MODE [TYPE A] Equipment Required a. USB storage device b. Remote Control Unit Firmware Update Procedure User Upgrade (Filename example: TVNB012_00_UF_XX91_AA.ecc) Upgrade the firmware only. The setting values will not be initialized. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_”...
  • Page 26 Factory Upgrade (Firmware Upgrade/Flash Upgrade) Firmware Upgrade (Filename example: FACT_TVNB012_00_UF_XX91_AA.ecc) Upgrade the firmware and initialize the setting values. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_”...
  • Page 27 [TYPE B] Equipment Required (Files included in the USB storage device are displayed.) 1. USB storage device " * " differs depending on the models. 2. Remote Control Unit *****_******.upg Select an upgrade file Firmware Update Procedure *****_******.upg 1. Turn the power off and unplug the AC Cord. *****_******.upg 2.

  • Page 28: Troubleshooting

    TROUBLESHOOTING [Power Supply Section] FLOW CHART NO.1 The power cannot be turned on. Is the fuse (F600) normal? See FLOW CHART No.2 <The fuse blows out.> Check if there is any leak or short-circuit on the primary circuit component and repair it if defective. (C602, D604, D605, D607, D608, D609, D610, Q601, IC602, R611, R612, T601) Is the P-ON+12V line voltage normal?
  • Page 29 FLOW CHART NO.5 P-ON+12V is not output. Check D406, D407, D413, C411, C412 and their periphery circuit. Repair it if defective. FLOW CHART NO.6 AMP+24V is not output. FLOW CHART NO.7 LED+24V is not output. FLOW CHART NO.8 [TYPE A] AL+3.3V is not output.
  • Page 30 [Video Signal Section] FLOW CHART NO.1 The key operation is not functioning. Re-install the switches (SW4001~SW4006) correctly or replace the poor switch. Check the switches (SW4001~SW4006) and their periphery. Repair it if defective. Replace Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit.
  • Page 31 [Audio Signal Section] FLOW CHART NO.1 Audio is not output normally. See FLOW CHART NO.6 <AMP+24V is not output. [Power Supply Section]> See FLOW CHART NO.8 <AL+3.3V is not output. [Power Supply Section]> Replace Digital Main CBA Unit. PL12.3ATR...

  • Page 32: Block Diagrams [Type A]

    BLOCK DIAGRAMS [TYPE A] 1. System Control Block Diagram PL12.3ABLS...
  • Page 33 2. Video/Audio Block Diagram PL12.3ABLVA...
  • Page 34 3. Digital Signal Process Block Diagram PL12.3ABLD...
  • Page 35 4. Power Supply Block Diagram PL12.3ABLP...
  • Page 36 [TYPE B] 1. System Control Block Diagram PL12.3BBLS...
  • Page 37 2. Video/Audio Block Diagram PL12.3BBLVA...
  • Page 38 3. Digital Signal Process Block Diagram PL12.3BBLD...
  • Page 39 4. Power Supply Block Diagram PL12.3BBLP...

  • Page 40: Schematic Diagrams / Cba And Test Points

    SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
  • Page 41 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
  • Page 42 Power Supply Schematic Diagram CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. NOTE: CAUTION ! : For continued protection against risk of fire, If Main Fuse (F600) is blown , check to see that all components in the power supply The voltage for parts in hot circuit is measured using replace only with same type 4A, 125V fuse.
  • Page 43 IR Sensor Schematic Diagram C4054 R4060 R4053 RS4051 OPEN 4.7K GP1USC32XP (REMOTE SENSOR) D4051 SMLE12WBC7W1HR POWER R4051 R4052 TO DIGITAL MAIN 6.8K CBA UNIT CN3101 R4054 CN4052 or CN3105 1 AL+3.3V 2 P-ON+5V 3 LIGHT C4051 C4056 C4052 1000P 4 LED1 5 REMOTE C4053 C4055...
  • Page 44 Function Schematic Diagram FUNCTION CBA TO IR SENSOR CBA CN4051 CN4001 R4006 KEY-IN1 C4002 D4001 MM5Z5V6B D4002 OPEN R4005 R4004 R4003 R4002 R4001 2.2K 2.2K 2.7K SW4006 SW4005 SW4004 SW4003 SW4002 SW4001 POWER CH UP MENU DOWN DOWN UNLESS OTHERWISE SPECIFIED: SWITCHES ARE SKRMAAE010.
  • Page 45 Digital Main 1 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. R3081 DIGITAL MAIN CBA UNIT D3008...
  • Page 46 Digital Main 2 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT TU3901 TUNER UNIT IC3013...
  • Page 47 Digital Main 3 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. C3009 IC3005(3/6) OPEN...
  • Page 48 Digital Main 4 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. R3218 OPEN CONTINUE...
  • Page 49 Digital Main 5 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 4 CHECK+1.8V...
  • Page 50 Digital Main 6 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE HDMI- DIGITAL 4...
  • Page 51 Digital Main 1 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 8 P-ON+12V/+21V...
  • Page 52 Digital Main 2 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3101(2/8) MN2WS0172A...
  • Page 53 Digital Main 3 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section. CONTINUE (NO CONNECTION) CN3111...
  • Page 54 Digital Main 4 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 6 P-ON+3.3V...
  • Page 55 Digital Main 5 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 8...
  • Page 56 Digital Main 6 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section. IC3101(6/8) DIGITAL MAIN CBA UNIT MN2WS0172A...
  • Page 57 Digital Main 7 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 4...
  • Page 58 Digital Main 8 Schematic Diagram [TYPE B] DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 7 DC-DC-EN D3611 R3682 R3607 MM5Z7V5B Q3601 R3683 C3702 R3904 C3604 R3695 2SA1576UBTLQ 100K OPEN OPEN OPEN OPEN (SWITCHING) R3608 CONTINUE DIGITAL 4 P-ON-H2 R3609 R3610 4.7K D3614 4.7K IC3601...
  • Page 59 Digital Main 9 Schematic Diagram [TYPE B] CONTINUE DIGITAL 6 DIGITAL MAIN CBA UNIT AL+3.3V CONTINUE DIGITAL 8 P-ON+5V Q3108 R3200 R3206 R3215 CONTINUE OPEN OPEN OPEN OPEN DIGITAL 4 SW-EN LED1 REMOTE R3207 OPEN R3102 R3209 R3188 OPEN OPEN TO IR SENSOR R3107 CBA CN4052...
  • Page 60 Digital Main 10 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT R3875 R3738...
  • Page 61 Power Supply CBA Top View Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. Also, in order to have the ability to increase the input slowly, CAUTION ! : For continued protection against risk of fire,...
  • Page 62 Power Supply CBA Bottom View Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. Also, in order to have the ability to increase the input slowly, CAUTION ! : For continued protection against risk of fire,...
  • Page 63 IR Sensor CBA Top View TP4053 IC4051 D4051 TP4052 RS4051 IR Sensor CBA Bottom View CN4052 BA21P6G0203 1 D4052 C4055 R4057 R4054 C4056 R4059 R4051 C4051 R4060 R4053 R4056 C4054 C4052 R4052 R4055 C4053 R4058 C4057 A30C5 C7A3 BA21P6G02031_1 10-24...
  • Page 64 Function CBA Top View BA21P6G0203 1 CN4001 A30C5 C7A3 Function CBA Bottom View C4002 R4006 R4004 R4003 R4001 R4005 R4002 D4002 D4001 BA21P6G0203 1 BA21P6G02031_2 10-25...

  • Page 65: Wiring Diagrams [Type A]

    WIRING DIAGRAMS [TYPE A] 11-1 PL12.3AWI...
  • Page 66 [TYPE B] 11-2...

  • Page 67: Exploded Views

    EXPLODED VIEWS [TYPE A] B14-1 Power Supply CBA B14-2 Digital Main CBA Unit LCD-1 CL401 CL3701 CL3801 CL3101 IR Sensor CBA CL3013 CL600 SP3802 Function CBA CL4051 SP3801 SSK1 See Electrical Parts List for parts with this mark. Some Ref. Numbers are not in sequence.
  • Page 68 [TYPE B] B14-1 Power Supply CBA B14-2 Digital Main CBA Unit LCD-1 CL3701 CL401 CL3801 CL3101 IR Sensor CBA CL3013 CL600 SP3802 Function CBA CL4051 SP3801 SSK1 See Electrical Parts List for parts with this mark. Some Ref. Numbers are not in sequence.
  • Page 69 Packing Tape SSK1 Tape TYPE B Packing Tape Packing Tape Some Ref. Numbers are not in sequence. 12-3 PL12.3PEX...

  • Page 70: Parts List

    PARTS LIST [40PFL4707/F7 (Serial No.: DS1), 40PFL4707/F8 (Serial No.: XA1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. SP3801 SPEAKER MAGNETIC BOX 8OHM/10W SB- DS08050XQ015 05F71B Before replacing any of these components, read...

  • Page 71: Electrical Parts

    Electrical Parts PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C652 CHIP CERAMIC CAP .(1608) B K 0.1µF/50V CHD1JK30B104 Before replacing any of these components, read CONNECTORS carefully the product safety notice in this service CN401 CONNECTOR BASE TOP 13P B13B-PH-K- J3PHC13JG029...
  • Page 72 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 3216 1/4W J 15k Ω RESISTORS R624 RRX4153HH034 RES CHIP 3216 1/4W J 15k Ω RES CARBON FILM T 1/4W J 120 Ω R625 RRX4153HH034 R401 RCX4121T1001 METAL OXIDE FILM RES. 2W J 47 Ω RES CARBON FILM T 1/4W J 120 Ω...
  • Page 73 Ref. No. Description Part No. SW4006 TACTILE SW. SKRMAAE010 SST0101AL064 IR SENSOR CBA Ref. No. Description Part No. IR SENSOR CBA ---------- Consists of the following CAPACITORS C4051 CHIP CERAMIC CAP .(2125) B K 10µF/6.3V CHE0KK30B106 C4052 CHIP CERAMIC CAP .(1005) B K 1000pF/50V CHB1JK30B102 C4053 CHIP CERAMIC CAP .(1005) F Z 0.1µF/16V...

  • Page 74: Revision History

    REVISION HISTORY Chassis PL12.3 • 2012/03/06 40PFL4707/F7 (Serial No.: DS1) Added • 2012/03/29 40PFL4707/F8 (Serial No.: XA1) Added • 2012/03/19 40PFL4907/F7 (Serial No.: DS1) First Draft Added 14-1 PL12.3REV...
  • Page 75 COMPARISON LIST OF MODEL NAMES Chassis PL12.3 40PFL4707/F7 (DS1) A21P6UH 40PFL4707/F8 (XA1) A21PAMA 40PFL4907/F7 (DS1) A27P6UH PL12.3COM...

This manual is also suitable for:

40pfl4907/f740pfl4707/f8

Table of Contents