Table of Contents
Advertisement
7) Following screen will appear. Use [s / B] to select
"Yes", then press [OK] to go to "Advanced Settings".
• For further operation, refer to "Advanced Settings" on
page 62.
• To go back to the home menu, press [
Network Connection
Wireless router settings are incomplete.
Please use "Advanced Settings"
to complete your setup.
Yes
Note
• For a wireless network with authentication setting,
key icon appears to the right hand of the wireless
network name (SSID).
• Signal icon shows the strength of the signal.
• WEP/WPA key appears as asterisks on the
confirmation screen.
• The supplied USB wireless LAN adaptor supports
following specifications.
- Wifi standards
- Frequency spectrum : 2.4GHz
- Security protocol
Manually enter your SSID
Set up the connection to the wireless router manually by
entering the wireless network name (SSID).
1) Follow steps 1) to 3) in "Find wireless network" on
pages 61-62.
2) Use [K / L] to select "Manually enter your SSID",
then press [OK].
• Wireless Router Name (SSID) entry screen will appear.
Enter the wireless network name (SSID) using cursor
buttons, number buttons and color key, then press
[YELLOW].
Manually enter your SSID
Wireless Router Name (SSID)
1
2
3
4
5
6
a
b
c
d
e
f
k
l
m
n
o
p
u
v
w
x
y
z
Clear
All Clear
3) Follow steps 6) to 7) in "Find wireless network" on
pages 61-62.
Wireless Router Status
You can check the current status of "Wireless Router"
setting.
1) Follow steps 1) to 3) in "Find wireless network" on
pages 61-62.
2) Use [K / L] to select "Wireless Router Status", then
press [OK].
• The list of current wireless router setting will be
displayed.
3) Press [BACK
] to go back to the previous screen,
or press [
(home)] to go back to the home menu.
62
EN
(home)].
No
: IEEE 802.11 b/g/n
: WEP / WPA / WPA2
7
8
9
0
g
h
i
j
q
r
s
t
.
-
_
OK
a/A/@
OK
SETUPS
Advanced Settings
After you set up the "Wireless Router" setting, set the
network setting to "Standard" (wireless) or
"Manual"(wireless).
Standard (wireless)
To set the network setting to "Standard"(wireless), follow
the following procedure. For details of this setting, refer to
"Standard (Wired)" on page 58.
• If you select "Yes" in step 7) of "Find wireless network" on
pages 61-62, skip to step 3).
1) Follow steps 1) to 2) in "Find wireless network" on
pages 61-62.
2) Use [K / L] to select "Advanced Settings", then
press [OK].
3) Use [K / L] to select "Standard", then press [OK].
Manual (wireless)
To set the network setting to "Manual"(wireless), follow
the following procedure.
• If you select "Yes" in step 7) of "Find wireless network" on
pages 61-62, skip to step 3).
1) Follow steps 1) to 2) in "Find wireless network" on
pages 61-62.
2) Use [K / L] to select "Advanced Settings", then
press [OK].
3) Use [K / L] to select "Manual", then press [OK].
• For details of each setting, refer to following pages.
"IP Address Setting" / "DNS Setting":
Refer to "IP Address Setting / DNS Setting" on page 59.
"Proxy Setting":
Refer to "Proxy Setting" on page 60.
"BD-Live Setting":
Refer to "BD-Live Setting" on page 61.
"Network Status":
Refer to "Network Status" on page 61.
Note
• You cannot select "Advanced Settings" if "Wireless
Router" setting is not completed.
Disable
Deactivate all the network connection and settings.
1) Follow steps 1) to 2) in "Standard (Wired)" on page
58.
2) Use [K / L] to select "Disable", then press [OK].
3) Use [K / L] to select "Yes", then press [OK].
4) Press [BACK
or press [
(home)] to go back to the home menu.
Note
• The network connection can be reactivated by
setting the network connection to "Enable (Wired)"
or "Enable (Wireless)".
] to go back to the previous screen,
Advertisement
Table of Contents
