Advertisement
ANTENNA LOCATION
This is an outdoor antenna, but it may also be used indoors. For best
results, mount the J9170A facing towards the center of the coverage
area. A line-of-sight path between the antenna and active area works
best. Avoid mounting next to a column or vertical support that could
create a shadow zone and reduce coverage.
ASSEMBLY AND MOUNTING
The J9170A is shipped with a heavy duty articulating mounting kit (HP
5070-6360) that provides wide-range articulation in both the azimuth and
elevation planes. The kit allows mounting on a mast (up to 2 inches or 5.1
cm), or on a wall using wall anchors.
WALL MOUNT
CONFIGURATION
Figure 1
MOUNTING HARDWARE
Item Description
1
Bracket, Flange
2
Bracket, Linkage
3
5/16 Flat Washer
4
5/16 Lock Washer
5
5/16 x 1-5/8 Hex Head Bolt
6
5/16 Nut
7
Double Serrated Lock Washer
8
1/4 Flat Washer
9
1/4 Lock Washer
10
1/4 Nut
11
Clamp
12
Expansion Anchor
13
1/4 x 1-3/4 Hex Head Bolt
2
ANTENNA
INSTALLATION
BRACKET
ASSEMBLY
Figure 2
MAST MOUNT
CONFIGURATION
Qty
2
1
4
2
2
2
2
8
8
4
2
4
4
HP 10.9/13.5 dBi Dual-Band Point-to-Point 3-Element MIMO Directional Antenna (J9170A) Guide
Assemble and mount the antenna as follows.
(See Figure 1 for wall mount and Figure 2 for pole/mast mount.)
1. Attach the antenna mount (1) to the exposed studs on the back of the
antenna using 4 SS 1/4"-20 hex nuts (10), 4 1/4"-20 SS flat washers (8)
and 4 1/4"-20 SS lock washers (9)
2. Secure one side of the articulating arm (2) with 1 SS [M8] washer
external serrated (7), to the antenna mount (1) using 1 Bolt size SS
5/16"x 1-5/8"(5), 1 SS 5-16" split lock wash (4), 2 SS flat washer 5-16"
(3) and 1 hex nut 5-16" (6) assemble as shown.
3. For mounting on a wall:
a. Using the other supplied antenna mount bracket (1) as a template
to mark holes locations, for drilling see wall diagram figure 3 for
holes size.
b. Install 4 wall expansion anchors (12).
c. Install to wall the antenna mount bracket using four SS HEX
1/4"-20 screws (13), 4 SS 1/4"-20 flat washers (8), 4 1/4"-20 lock
washer (9). Or, for mounting on a pole or mast, attach the two hose
clamps (11) to antenna mount bracket (1) and encircle the pole with
each clamp and tighten.
4. Attach the pre-assembled antenna with both (1) and (2) to the other
bracket (previously mounted) using 1 SS washer external serrated (7),
using 1 Bolt size SS 5/16" 1-5/8" (5), 1 SS 5-16"split lock washer (4), 2
SS flat washer 5-16" (3) and 1 hex nut (6) 5-16" assemble as shown.
Use the screw (5) to attach the free end of the articulating arm to the
mount and then secure it in place with SS hex nut (6).
5. Loosen the pivot screws (1-5/8" bolt screw (5)) as needed to position
the antenna for desired azimuth and elevation. When the antenna is
fully adjusted, tighten all hardware securely.
Figure 3
Advertisement
