Page 1
Black Wolf POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 SEPTEMBER 2010 51-905710-000...
Page 2
BLACK WOLF NOTE: Please use the instructions in this manual to assemble the tables shown below. Illustrations may be different depending on the table being assembled. Also note that careful handling of all components will assure damage-free assembly. PAGE 2...
Page 3
BASE FRAME AND LEG ASSEMBLY BLACK WOLF FIGURE ONE Step #1: Securely attach leg panels to leg posts using #8 x 1-1/2” truss head screws. Step #2: Repeat Step #1 to create second leg assembly. PANEL #8 x 1-1/2” TRUSS HEAD...
Page 4
BASE FRAME AND LEG ASSEMBLY (CONTINUED) BLACK WOLF FIGURE THREE Step #5: Position the two leg assemblies approximately the length of the base frame. Step #7: Carefully lower the base frame over the legs. FIGURE THREE FIGURE FOUR Step #8: Align the clearance holes in the leg posts with the clearance holes in the side sills and attach securely with 5/16-18 x 3”...
Page 5
SLATE ASSEMBLY BLACK WOLF FIGURE ONE CENTER SLATE SECTION Step #1: Position the center slate section evenly between the two base frame cross supports as shown, carefully center the slate section so there is an equal amount of overhang at each side of the base frame.
Page 6
ATTACHING BILLIARD CLOTH TO UNFRAMED SLATE BLACK WOLF Before attaching the billiard cloth, clean slate thoroughly. FIGURE ONE Step #1: Lay the bed cloth over the top of the slate, nap side up. Leave an equal amount of cloth overhang at the ends and sides of the slate.
Page 7
ATTACHING BED CLOTH TO FRAMED SLATE BLACK WOLF Before attaching the billiard cloth, clean slate thoroughly. FIGURE ONE Step #1: Lay the bed cloth over the top of the slate, nap side up, with the nap running from the head end to the FOOT foot end of the table.
Page 8
ATTACHING BED CLOTH TO FRAMED SLATE (CONTINUED) BLACK WOLF FIGURE FOUR FOOT Step #11: At location #9, cut a short slit in the cloth at the edge centered on the side pocket opening. Grasp the cloth firmly above this slit, pull the cloth into the side pocket opening and tack or staple to the wood frame.
Page 9
RAIL ASSEMBLY BLACK WOLF FIGURE ONE Step #1: Place corner casting upside down on floor. Seat end and side rail clearance holes onto corner casting posts. Step #2: Firmly hold end and side rails together, keep them, square by using a carpenter’s square against the cushions.
Page 10
APRON ASSEMBLY BLACK WOLF FIGURE ONE #12 x 2” Step #1: With the rails remaining face down, attach PAN HEAD SCREW aprons as shown. Aprons must overhang equally at each end. #12 FLAT WASHER (9/16 O.D.) NOTE: Gully apron to be located at foot end of table.
Page 11
APRON ASSEMBLY (CONTINUED) BLACK WOLF FIGURE FOUR Step #4: Position a dome lockwasher onto the stud, then thread a 3/8-16 hex nut onto the stud . Step #5: Repeat this step for all 18 stud locations. Step #6: Fasten the rails tightly at the ends first. Then while making sure that the side rails form a straight line, 3/8-16 x 2-3/4”...
Page 12
GULLY ASSEMBLY (IF REQUIRED) BLACK WOLF FIGURE ONE NAME PLATE Step #1: Gully apron to be located at the foot end of the HEAD END table as shown. GULLY APRON FOOT FIGURE ONE GULLY POCKETS FIGURE TWO Step #2: Attach gully pockets and gully tubes as shown.
Need help?
Do you have a question about the Black Wolf and is the answer not in the manual?
Questions and answers