Table of Contents
Advertisement
Playback connection
Connect to a Stereo Amplifier with Audio Output
If your DVD/VCR is connected to a stereo amplifier, the video soundtrack can output through the loudspeakers of
the stereo system.
SCART-cable (not supplied)
SCART-Socket
(for TV-RGB/Composite)
DVD/VCR
Stereo Amplifier
Audio (L) Output
Audio (R) Output
AUDIO Cord (not supplied)
Connect to an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems
such as Dolby Digital and DTS by using the Coaxial Digital Output.
Use this connection to connect an:
• AV amplifier with built-in *Dolby Digital decoder
• AV amplifier with built-in *DTS decoder
SCART-cable (not supplied)
DVD/VCR
SCART-Socket
(for TV-RGB/Composite)
Coaxial digital
Coaxial digital cable
Audio Output
(not supplied)
Connecting the optical digital cable
You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital
cable.
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.
When not using the optical digital cable, attach the dust protection cap to protect against dust.
NOTES:
• The OPTICAL, COAXIAL jacks are useful only for DVD section.
VHS signal is output only from the SCART-sockets, AUDIO L/R jacks and RF OUT jack.
• When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV
Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the
speakers to be damaged.
• DTS audio will be output only from the COAXIAL output. To hear DTS audio, DTS-Decoder is necessary.
When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.
• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
12
On-screen Language Selection
Turn on your TV and select the VCR
Preparation
channel which you have already tuned
• Press the
on your TV. The TV will switch to AV
• Press VCR to select the VCR mode. (The VCR indicator will
(VCR mode) automatically by the Scart
light)
lead connection. The on-screen menu
can display any of three languages;
English, German and French.
1
Press VCR MENU. Press
SETUP.
Then press ENTER.
VCR
DVD
OPEN/CLOSE
CLOCK
COUNTER
ANGLE
COUNTER RESET
2
AUDIO
SUBTITLE
Press
TV/VCR
AUX
AUDIO SELECT
ATR
the LANGUAGE. Then
PLAY MODE
press ENTER.
MEMORY
ZOOM
E.A.M
SP/LP
DISPLAY
TIMER REC
REC/OTR
RETURN
CALL
PLAY
3
REW
FWD
Press
the desired language.
SLOW
PAUSE/STILL
Then press ENTER.
STOP
INDEX – SKIP INDEX +
TITLE
A-B RPT
SET UP
CH +
MENU
ZERO RETURN
VCR MENU
INSTANT SKIP
SET –
SET +
ENTER
4
CH –
Press VCR MENU repeatedly until the TV picture
CANCEL
VIDEO Plus+
appears on the screen.
Notes:
• If the unit does not operate properly,
or No key operation (by the unit and /
or the remote control): Static electric-
ity, etc., may affect the player's opera-
tion. Disconnect the AC power cord once,
then connect it again.
• If you use the unit for the first time and
press VCR MENU, instead of the MENU
screen in steps 1 and 2, the one in step 3
may appear. This is normal for this DVD/
VCR and is no indication of a malfunc-
tion.
Please first select the language to oper-
ate this unit.
14
To SCART
input
TV
To Audio (L) Input
To Audio (R) Input
To SCART
input
TV
AV Amplifier with
built-in various
decoder as above
button to turn on the DVD/VCR.
or
to select the SYSTEM
TIMER REC SET
AUTO REPEAT
OFF
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER
: ENTER
EXIT
: MENU
or
to select
SYSTEM SETUP
CLOCK SET
LANGUAGE/SPRACHE/LANGUE
SELECT :
ENTER
: ENTER
EXIT
: MENU
or
to select
LANGUAGE/SPRACHE/LANGUE
ENGLISH
DEUTSCH
FRANCAIS
SELECT :
OK : ENTER
Tuning the TV Stations and Setting the Time and
Plug your DVD/VCR into the mains sup-
Preparation
ply and it will start to automatically tune
•
Make sure that your DVD/VCR is connected properly to the TV.
•
itself in and set the correct date and
If a satellite receiver is connected with the coaxial lead, make
time. After setting itself up, you must
sure it's switched ON and set to SKY ONE.
set the TV to the video channel.
•
Turn on the TV and select the channel you wish to allocate for
video use.
1
Plug your DVD/VCR's plug into the mains supply. "Auto"
will start to flash in the display. Your DVD/VCR will auto-
matically tune itself in and set the correct
time and date (This may take
approx. 4 minutes).
2
Press and hold the
VCR in the Standby mode until "rF"
and RF output channel "36" will
appear in the display.
3
If you have used a 21PIN scart lead you now, simply se-
lect the AV channel on your TV and go to step 5. Tune the
TV in the same way as tuning in a TV broadcast station
Notes:
until the word "TEST" flashes on the TV screen. Refer to
• The DVD/VCR automatically corrects
the TV operating instructions for tuning.
the clock setting every hour and
automatically adjusts the clock setting
Now the output from the DVD/VCR is
for Daylight Saving Time.
tuned to this channel. Whenever you
• Your DVD/VCR will tune the TV
want to play back a tape, select this
stations as follows.
channel.
CH 1
BBC 1
CH 2
BBC 2
4
If there is interference in the picture (wavy lines, picture
CH 3
ITV
roll, etc.), press CHANNEL on your DVD/VCR to select
CH 4
Channel 4
any RF channel between 23 and 69, retuning your TV until
CH 5
Channel 5
the word "TEST" flashes on the TV screen.
CH 6
Satellite
CH 7
etc.
If you connected a satellite receiver as explained on page
For VIDEO Plus+ recording to work
11, you must switch off the DVD/VCR's transmitter. Press
correctly, this order should not be
the VCR's CHANNEL repeatedly until OFF appears in the
changed.
display window (OFF will appear
• If you want to change the RF output
after 69 or before 23).
channel or switch to "OFF", press and
hold the DVD/VCR
on the front of
your DVD/VCR in the Standby mode
5
Press the
until the current RF output channel
Now the TV is tuned to your DVD/VCR.
appears. Press CHANNEL on your
DVD/VCR to select the RF channel you
To skip a channel position
desire.
Unwanted channels can be
• Skipped channels still may be selected
skipped so that they cannot
directly through the 1 to 0 keys.
be called up by pressing
• To cancel skipping select the skipped
CHANNEL. Select the
channel using the 1 to 0 keys, then
channel to be skipped,
press CANCEL. The channel No. does
not blink any longer, and the channel
No. now may be selected again using
CHANNEL.
...e.g. channel 29. Select channel 29, then press
CANCEL.
This channel's number will be flashing. That way you can
cancel further channels one after the other.
Setting the Time and Date Manually
You must set the date and time manually
Preparation
for timer recordings if Automatic tuning
• Turn on the TV, and select the VCR channel on TV.
process did not set them correctly.
• Press VCR to select the VCR mode. (The VCR indicator will light)
Example: Setting the clock to 11:30, 26 Oct. 2002.
1
Press VCR MENU. Press
VCR
DVD
SETUP. Then press
ENTER.
OPEN/CLOSE
The step-2 will appear
CLOCK
when clock is not set.
COUNTER
ANGLE
COUNTER RESET
AUDIO
SUBTITLE
TV/VCR
AUX
AUDIO SELECT
ATR
PLAY MODE
ZOOM
2
MEMORY
E.A.M
SP/LP
Press
DISPLAY
the CLOCK SET. Then
TIMER REC
REC/OTR
RETURN
CALL
press ENTER.
PLAY
REW
FWD
SLOW
PAUSE/STILL
3
STOP
Press
until 26 appears. Then
press
INDEX – SKIP INDEX +
TITLE
A-B RPT
SET UP
VCR MENU
CH +
MENU
ZERO RETURN
SET –
SET +
INSTANT SKIP
ENTER
CANCEL
CH –
VIDEO Plus+
4
Set the month, year, hour and minute in the same way
as in step 3. Then press ENTER.
• In case of an error,
press
one step and enter
again.
Notes:
• The AUTO TIME function adjusts the
5
Press
clock only if the error is within 5
The VCR automatically corrects the clock setting every
minutes.
hour once you set AUTO TIME to ON.
• The VCR automatically adjusts the
clock setting for Daylight Saving Time
6
once you set AUTO TIME to ON.
Press VCR MENU repeatedly until the TV picture
appears on the screen.
7
The clock will begin operation.
Date Automatically
8+4
52
button on the front of your DVD/
8+4
52
TEST
8+4
52
button to turn OFF the DVD/VCR.
CH 29
VCR
SP
CH
13
or
to select the SYSTEM
TIMER REC SET
AUTO REPEAT
OFF
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER
: ENTER
EXIT
: MENU
or
to select
SYSTEM SETUP
CLOCK SET
LANGUAGE/SPRACHE/LANGUE
SELECT :
ENTER
: ENTER
EXIT
: MENU
or
repeatedly
CLOCK SET
DAY
26 WED
MONTH
1
to continue.
YEAR
2000
TIME
0: 00
AUTO TIME
ON
SELECT :
SET
:
OK
: ENTER
EXIT : MENU
CLOCK SET
DAY
26 SAT
MONTH
10
to go back to
YEAR
2002
TIME
11: 30
AUTO TIME
ON
SELECT :
SET
:
OK
: ENTER
EXIT : MENU
or
to select AUTO TIME ON or OFF.
VCR
SP
CH
15
15
Hide quick links:
Advertisement
Table of Contents
