Related Manuals for Rear view safety RVS-7709900
Summary of Contents for Rear view safety RVS-7709900
-
Page 1: Instruction Manual
Instruction Manual Backup Camera System with Waterproof Monitor RVS-7709900 Rear View Safety, Inc. © 2016 Reverse With Confidence ™... -
Page 2: Table Of Contents
Troubleshooting......29 Warranty & Disclaimer......30-31 Rear View Safety... -
Page 3: Introduction
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle. -
Page 4: Safety Information
Rear View Camera System. If you back up while looking only at the monitor, you may cause Rear View Safety... - Page 5 INSTALLATION: • Electric shock or product or disconnected wire may cause a malfunction may occur if this fire. product is installed incorrectly. • While installing the Rear View System be careful with the wire • Use this product within positioning in order to avoid wire the voltage range specified.
- Page 6 If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
-
Page 7: Before Beginning Installation
Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. -
Page 8: Installation Guide
To connect a second camera, connect it to the CAM1 input. It can be turned on by pressing the power button on the monitor. Rear View Safety... - Page 9 Precautions For Use Of Monitor I. The Monitor is made of glass and plastic. Do not subject it to a mechanical shock by dropping it from a high place, etc. II. Do not apply excessive force to the monitor surface or the adjoining areas since this may cause the color tone to vary.
-
Page 10: Accessories
ACCESSORIES Rear View Safety... - Page 11 Product Features 1. 7” high resolution TFT LCD color monitor 2. Multiple image options (Horizontal/Vertical/Mirror/Normal) 3. Select from 8 languages 4. Automatic button backlighting and automatic brightness control 5. Full functional remote control 6. Multiple video formats (AUTO/PAL/NTSC) 7. 3 camera inputs 8.
-
Page 12: Monitor Specification
8. Resolution: 800× 3 (RGB) × 480 9. Contrast: 500:1 10. Brightness: 400cd/m2 11. Viewing Angle: U: 50° / D: 70°, R/L: 70°/ 70° 12. Operating Temperature: -20~+70ºC, RH90% 13. Storage Temperature: -30~+80ºC, R 90% 14. Waterproof Rating: IP69K Rear View Safety... -
Page 13: Monitor Installation
Reverse With Confidence ™... -
Page 14: Connections
RED 12V power wire to an ignition power source, the BLACK 12V wire to a chassis ground, the BROWN wire to reverse power, the WHITE wire to left turn signal power and the BLUE wire to right turn signal power. Rear View Safety... -
Page 15: Monitor Buttons
1. Sensor for remote signal 2. Power button 3. Increase / decrease the volume and switch sub-menu values 4. Move menu selection down 5. Menu button 6. Manual camera switch Reverse With Confidence ™... -
Page 16: Remote Operations
Remote Operations MUTE: ENABLE/MUTE sound POWER: Turn monitor on/off : Flip image horizontally Rear View Safety... - Page 17 CH: : Flip image vertically CH: Toggle selection up CH: Toggle selection down MENU: Access menu MODE: Toggle picture modes (PERSONAL / STANDARD / SOFT / VIVID / LIGHT) : Decrease brightness : Increase brightness CALL: Display currrent video channel source TIMER: Set a timer to shut down the monitor (10 minute increments, 10-90 minutes) LANG: Change languate...
-
Page 18: Wiring
4. Connect RED 12V power wire to an ignition power source 5. BLACK 12V wire to a chassis ground 6. BROWN wire to reverse power 7. WHITE wire to left turn signal power 8. BLUE wire to right turn signal power Rear View Safety... -
Page 19: Trigger Setting
Reversing Display: When the white wire is connected to left turn signal power, the monitor auto- matically switches to CAM1 (left side camera) when the left turn signal is acti- vated. Cam1 When the blue wire is connected to right turn signal power, the monitor auto- matically switches to CAM2 (right side camera) when the right turn signal is activated. -
Page 20: Distance Grid Lines
CAM 3 (backup camera) when the vehicle is put into reverse. The distance grid lines will automatically display. AUTOSCAN: When ON, this setting allows the system to automatically switch between connected camera inputs at a predetermined pace. Rear View Safety... -
Page 21: Menu
Menu Press MENU 1-4 times to display the following options and settings: 1. PICTURE 2. OPTION 3. SYSTEM 4. AUTO SCAN Picture The PICTURE sub-menu inclues BRIGHT, CONTRAST, COLOR, VOLUME, AUTO DIM, and SCALE ADJUST. Reverse With Confidence ™... -
Page 22: Normal Mode
When AUTO DIM is ON in a dark environment, the on-screen display enters dim mode. When AUTO DIM is turned ON or OFF in a bright environment, the on-screen display remains the same. Dim Mode Normal Mode Rear View Safety... - Page 23 Press to select SCALE ADJUST (ability to adjust grid lines) Reverse With Confidence ™...
-
Page 24: Menu
OPTION The OPTION sub-menu includes LANG , SCALE , CAM1 , CAM2, and CAM3. Rear View Safety... - Page 25 SYSTEM The SYSTEM sub-menu includes COLOR-SYS, BLUE BACK, HORIZONTAL, VER- TICAL, and ZOOM. Reverse With Confidence ™...
- Page 26 AUTOSCAN The AUTO SCAN sub-meun incldes AUTO SCAN, SCAN TIME, CAM1 , CAM2, and CAM3 Rear View Safety...
-
Page 27: Camera Dimensions
Camera Dimensions • 18 Infra-red illuminators (enables you to see in total darkness) • 1/4 Sharp® color CCD, 250k pixels, 2.1 mm wide lens with 130° angle • Shock resistant with a 20G Vibration and 100G impact rating • Built-in high gain microphone Reverse With Confidence ™... -
Page 28: Camera Specification
1VP - P, 75 Ω IR SWITCH CONTROL ACDS AUTOMATIC CONTROL VIBRATION AND SHOCK RATING 20G / 100G OPERATING TEMPERATURE -40°C ~ +80°C / RH 95% MAX STORAGE TEMPERATURE -40°C ~ +60°C / RH 95% MAX NET WEIGHT 22OZ Rear View Safety... -
Page 29: Troubleshooting
Troubleshooting Problem Possible Causes/Solutions No picture/sound Adaptor is connected incorrectly. Improper power supply. Unit is off. No picture Check AV cable connection. Audio cable improperly connected. Volume is off or set very low. No sound Dark picture Adjust brightness/contrast. Low environmental temperature. No color Adjust the color settings. -
Page 30: Warranty & Disclaimer
OTHERS OR THE UNAUTHORIZED USE OF NONCONFORMING PARTS; THE DAMAGE IS DUE TO NORMAL WEAR AND TEAR, THIS DAMAGE IS DUE TO ABUSE, IMPROPER MAINTENANCE, NEGLECT OR ACCIDENT; OR THE DAMAGE IS DUE TO USE OF THE REAR VIEW SAFETY, INC. SYSTEM AFTER PARTIAL FAILURE OR USE WITH IMPROPER ACCESSORIES. - Page 31 FOR ANY INJURY, LOSS OR DAMAGE, INCIDENTAL OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INTENDED USE OF THE PRODUCT. IN NO EVENT SHALL REAR VIEW SAFETY AND/OR ITS AFFILIATES HAVE ANY LIABILITY FOR ANY LOSSES (WHETHER DIRECT OR INDIRECT, IN...
- Page 32 If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE. Rear View Safety...
Need help?
Do you have a question about the RVS-7709900 and is the answer not in the manual?
Questions and answers