Table of Contents
Advertisement
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
•
If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Removing the unit
Before removing the unit, release the rear section.
When using the optional stay / 若選用支撐架
Fire wall
防火板
Dashboard
儀表板
Install the unit at an angle of less than 30˚.
將本機安裝在少於 30˚ 的角度。
*
1
When you stand the unit, be careful not to damage the fuse on the rear.
*
2
Avoid touching the connectors.
*
3
Not supplied for this unit.
TROUBLESHOOTING
•
The fuse blows.
*
Are the red and black leads connected correctly?
•
Power cannot be turned on.
*
Is the yellow lead connected?
•
No sound from the speakers.
*
Is the speaker output lead short-circuited?
•
Sound is distorted.
*
Is the speaker output lead grounded?
*
Are the "–" terminals of L and R speakers grounded in common?
•
Noise interfere with sounds.
*
Is the rear ground terminal connected to the car's chassis using shorter and thicker cords?
•
This unit becomes hot.
*
Is the speaker output lead grounded?
*
Are the "–" terminals of L and R speakers grounded in common?
•
This unit does not work at all.
*
Have you reset your unit?
Downloaded from Caradio-Manual.com Manuals
When installing the unit without using the sleeve / 若不使用外套機殼安裝本機
In a Toyota car for example, first remove the car radio and install the unit in its place.
以豐田牌（TOYOTA）汽車為例：首先取出汽車收音機，然後將本機裝入其空出的位置。
Stay (option)
支撐架（選用的）
Screw (option)
螺絲釘（選用的）
Note
注意
安裝（裝設、固定在儀表板內）
下面的圖解表示了典型的安裝程序。如果您有問題，或需要有關配套元件的資料，請向 JVC
汽車音響分銷商或配套元件供應公司詢問。
• 如果您不能確定如何正確地安裝本機，應請合格的技術人員來安裝。
Do the required electrical connections.
進行所需的電路連接。
拆卸本機
在拆卸本機前，應將本機後部的固定和連接部分鬆開。
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
按圖所示，將兩片板條型把手插入卡槽，然後
輕穩地從兩側向外拉兩片把手，本機隨之拉
出。
*
3
Flat head screws (M5 × 8 mm)
*
3
平頭螺絲釘（M5 × 8 mm）
*
3
Bracket
托座
*
3
Pocket
空殼
Bracket
托座
: When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are
used, they could damage the unit.
：把本機安裝在托座上時，務必使用 8 mm 長的螺絲釘。如使用過長的螺絲釘，會損壞本機。
*
1
您豎起本機時，小心不要損壞底部的保險絲。
*
2
避免接觸連接器。
*
3
不隨本機提供。
故障排除
•
保險絲燒斷。
*
檢查紅色導線接頭和黑色導線接頭是否接觸正確？
•
電源不能接通。
*
檢查黃色導線接頭是否接上？
•
揚聲器沒有聲音。
*
檢查揚聲器輸出導線接頭是否短路？
•
聲音失真。
*
檢查揚聲器輸出端子是否接地？
*
檢查揚聲器的左（L）、右（R）端子的負極"–"是否共同接地？
•
噪音干擾音響。
*
後接地端子與車身是否使用較短和較厚的電線連接？
•
本機發熱。
*
檢查揚聲器輸出端子是否接地？
*
檢查揚聲器的左（L）、右（R）端子的負極"–"是否共同接地？
•
本機完全不能操作。
*
您是否已經重置您的機組？
2
Bend the appropriate tabs to hold the
sleeve firmly in place.
弄彎機殼的突舌，把外套機殼牢固
在儀表板內。
Flat head screws (M5 × 8 mm)
平頭螺絲釘（M5 × 8 mm）
*
3
3
*
*
3
*
3
Hide quick links:
Advertisement
Table of Contents
