Table of Contents
Advertisement
Quick Links
THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM
AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITY
SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN
THIS BOOKLET. FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT
WORKING PROPERLY.
LOCATION FOR THE LIFE OF THE SECURITY SYSTEM. IF YOU DO NOT UNDERSTAND
ANY PART OF THIS MANUAL YOU SHOULD NOTIFY YOUR INSTALLING COMPANY AND
ASK FOR THAT SECTION OF THE MANUAL TO BE EXPLAINED FULLY.
The SECURITY CONTROL CENTER is turned on (ARMED) and off (DISARMED) by entering
a 4 digit code into the Keypad Control,, which is similar to a telephone keypad. The Keypad
Control includes 10 indicator lights and a built-in electronic sounder. These provide specific
information relating to the status of the security system which is described in this booklet.
Understanding what the lights and sounds mean will help you easily operate your system.
SO REMEMBER, READ THE ENTIRE MANUAL, AND IF POSSIBLE, PRACTICE ON THE
KEYPAD CONTROL WHILE YOUR PROFESSIONAL INSTALLER IS AT YOUR SITE. IF
YOU HAVE ANY QUESTIONS, ASK YOUR INSTALLING COMPANY.
PLEASE KEEP IN MIND THAT THE LEVEL OF SECURITY YOU WILL OBTAIN WITH THIS
SYSTEM RELATES SPECIFICALLY WITH TWO MAJOR FACTORS:
1. The quantity, quality, and placement of security devices attached to this system.
2. The knowledge you have of the security system and how that knowledge is utilized in a
weekly test of the complete system.
YOU SHOULD BE AWARE OF THE FOLLOWING FACTS AND USE THEM WHEN
PREPARING A SAFETY/SECURITY PLAN FOR YOUR HOME/BUSINESS.
1. Your security system is an electronic device and is subject to failure or malfunction. Do
not rely on it as your single source of security.
2. Your system should be tested weekly.
3. Your system will not work without power.
4. Warning devices will need to be loud enough, wired correctly, and properly placed to
provide notification of an alarm event.
5. Smoke and heat detectors may not detect heat and smoke in all situations.
6. Use qualified security professionals to select, install, and maintain your security system.
7. It may be possible to arm the security system without the backup battery connected. Your
periodic test should be done with A.C. Power removed to verify the battery is connected
and adequately charged.
8. Care should be taken to plug in and properly restrain the A.C. Transformer after testing.
PLEASE READ THIS ENTIRE BOOKLET CAREFULLY BEFORE OPERATING YOUR
SECURITY CONTROL SYSTEM. IF YOU DO NOT UNDERSTAND ANY PORTION OF THIS
MANUAL, OR IF YOU HAVE ANY QUESTIONS ABOUT YOUR SYSTEM, CONTACT THE
INSTALLING COMPANY LISTED ON PAGE 1 OF THIS BOOKLET.
THIS BOOKLET SHOULD BE KEPT IN AN ACCESSIBLE
2
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CADDX ranger 8600
Summary of Contents for CADDX ranger 8600
- Page 1 THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET. FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY.
-
Page 2: How To Bypass Zones
HOW TO ARM YOUR SECURITY SYSTEM To Arm the security system, close all of the protected doors and windows. The green "READY" light on the keypad control will be illuminated when all of the protected zones and sensors are secure. If any of the zones are bypassed, a sensor in that zone can be violated without affecting the "READY"... - Page 3 AUTOMATIC BYPASS OPTION If checked, the "AUTOMATIC BYPASS" option has been selected by your installing company. With this feature enabled, all interior zones will automatically bypass if you "ARM" your security system and do not leave through a designated entry/exit door. The "AUTOMATIC BYPASS" will occur at the end of the exit delay time.
- Page 4 THE CHIME FEATURE If checked, your security system will operate in the "CHIME" mode, allowing the monitoring of pre-designated zones while the security system is not armed. While in the "CHIME" mode, the opening of any of these zones will produce a 1 second beep from the keypad control. To activate this feature, press the "CHIME"...
-
Page 5: Duress Code
DURESS CODE If checked, your security system has a "DURESS CODE" option. If so, this code may be programmed to send a special message to the central monitoring station if you are forced to arm or disarm your security system against your will. Check with your Installing/Servicing company to see if this option has been enabled for your system. - Page 6 RESETTING YOUR SECURITY CONTROL CENTER In the event of a system malfunction in the Security Control Center, press the [#] (reset) key on the keypad control. This should reset the code sequence and restore normal operation. If the problem persists, call the service number located on page 1 of this booklet for service. AUDIBLE ALARM SOUNDS FIRE: Steady siren, pulsing bell (see page 1) or beeping keypad.
- Page 7 SERVICE CONDITION The “Ready” LED will flash in the event of a system fault. Press [U]-[2]-[2] to identify the source of the fault. One or more zone lights will illuminate indicating what service(s) is required. Call your service provider immediately for these problems. Below is a listing of what each light means in a service condition.
Need help?
Do you have a question about the ranger 8600 and is the answer not in the manual?
Questions and answers