Roland MT-32 Owner's Manual page 37

Program
change
•
Patch Change
Status
CnH
Sacond
PPH
pp
-
Patch
Number OH
-
7FH
{
-
127
)
n
-
MID! Channel
OK
-
FH
( 1
-
16
)
Program change information
is
used to
change
Patches.
Pitch Bender change
•
Pitch Bender
Status Second
Third
EnH
ilH
mmH
II
=
Pitch
Bender change
value
(
Lower
byte
)
00H - 7FH
(
-
127
)
mm
=
Pitch
Bender change
baiue
(
Upper
byte
5
OOH
-
7FH
(
-
127
)
n »
MIDI Channel
OH -
FH
( 1
-
16
)
Mode
message
•
All notes off
Status Sacond
Third
OOH BnH
7BH
n
-
MIDI Channel
OH
-
FH
( 1
-
16
)
Turns
off
all
notes
that
have been turned on by MID! Note
on.
Third
OOH
OH -
FH
( 3
-
16
>
Recognized
as
only At!
notes
off.
MT
—
32 remains
in
mode
3
(
omni
off.
poly
).
• OMNI
OFF
Status Sacond
BnH
7CH
n
=
MID
Channel
• OMNI
ON
Statu* Second
BnH 7DH
n
~
MID
Channel
Third
OOH
OH
-
FH
( 1
-
56
)
Recognized
as only All
notes
off.
MT —
32 remains
in
mode
3
{
omni
off,
poly
),
Third
OOH
OH
-
FH
( 1
-
16
)
Recognized
as
only
All
notes
off.
MT —
32 remains
in
mode 3
(
omni
off,
poly
).
• POLY
Statu*
Sacond
• MONO
Status
Second
BnH
7
EH
n
-
MIDI Channel
BnH
7FH
n
=
MIDI Channel
Third
OOH
OH
-
FH
(
1
-
16
)
Recognized
as only All
notes
off.
MT -
32 remains
in
mode
3
(
omni
off, poly
).
bxclusive
Statu*
FOH
:
System Exclusive
F7H
:
EOX
(End
Of
Exclusive)
Using exclusive message,
a set
of parameters
for
a timbre or
individual parameter;
in
a patch or timbre can be transferred
to
MT-32.
Refer
to
Roland Exclusive
Messages and
Sections 4
and
5.
Active sensing
Status
FEH
;
Active Sensing
Having received
this
message,
MT -
32 expects
to
receive
information
of
any
statu
or data every
300ms
(max).
If
MT -
32
fails
to
sense message,
it
assumes that
MIC
bus
is
disconnected
for
some
reasoa
Then
MT
- 32
turns off
all
notes
which hav
been turned on by MID! and returns to
normal
operation
<
will not
check
intervj
of
messages).
3.REC0GNIZED RECEIVE
DATA
(Rhythm
Part)
Messages on MIDI
channels not assigned to
rhythm
part are ignored.
Note event
•
Note off
Statu* Second Third
8nll
kkH vvH
9nH
kkH OOH
kk •
note
number
1BH - 57H
C
24
-
87)
vv
=
velocity
ignored
n
= MIDI Channel OH
-
FH
{
1
-
16
)
A
tone
whose
envelope
mode
is
"NO
SUS"
ignores Note off
message.
•
Note on
Status
9nH
Sacond
kkH
Third
vvH
kk
=
note
number
18H
- 57H
(
24
-
87
)
vv
=
velocity
OIH -
7FH
( 1
-
127
)
n
•
MIDI Channel
OH -
FH
( 1
-
16
)
Note numbers
outside of the range 24
-
87
are ignored.
Control
change
•
Modulation Depth
Status Second
BnH OIH
Third
vvH
vv
=
Modulation depth
OOH
-
7FH
(
-
127
)
n = MID) Channel OH
-
FH
( 1
-
16
)
>
Data Entry
Status
BnH
Second
06H
Third
vvH
vv
= Value
of a
parameter
specified
by RPC. (See
description in
RFC
MSB.)
n =
MIDI Channel
OH - FH
( 1
-
16
)