1. Manuals
  2. Brands
  3. Recon Manuals
  4. 3D Glasses
  5. JET PRO
  6. User manual

Recon JET PRO User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
RECON JET
PRO
TM
User Manual
Assembled in USA

Advertisement

Table of Contents
loading

Summary of Contents for Recon JET PRO

  • Page 1 RECON JET User Manual Assembled in USA...
  • Page 2 Jet Pro blocks part of your normal field of vision. Do not use while driving. If you use Jet Pro in the workplace to operate mobile equipment, use Jet Pro with special care such as spotters and protected driving areas, and be aware that your field of vision is partially blocked.

  • Page 3: Table Of Contents

    CONTENTS SAFETY INFORMATION WELCOME JET PRO SYSTEM FEATURES (ENGINE) WHAT’S IN THE BOX SETTING UP JET PRO ADJUSTING THE EAR STEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 ADJUSTING THE NOSEPIECE .

  • Page 4: Welcome

    • Press and hold BACK/POWER for 2 seconds to power Display on Jet Pro. Hold for 5 seconds to power off Jet Pro. Jet Pro’s display looks like a 30” screen seen from a Hold for 9 seconds to force shutdown (not recom- distance of 7 feet (2 m).

  • Page 5: Setting Up Jet Pro

    SETTING UP JET PRO 1. REMOVE THE BATTERY PROTECTOR TAB 3. POWER ON JET PRO Hold Jet Pro with one hand and pull the tab straight up To power on Jet Pro, press and hold the BACK/POWER with the other.

  • Page 6: Adjusting The Ear Stems

    F/40 C or below -4 F/-20 C) may cause permanent damage. • Jet Pro complies with the IEC IP65 standard for water and dust resistance, but it is not waterproof. Exposure to heavy and prolonged rain might damage the device.

  • Page 7: Parts Assembly

    PARTS ASSEMBLY Your Jet Pro comes as a pre-assembled unit. This section shows how to safely detach Jet Pro’s components: the engine, battery, lens, and nosepiece. WARNING: When removing Jet Pro’s engine or battery, take care to avoid damaging the frame and the other components.

  • Page 8: Nosepiece

    REPLACING THE LENS 1. Make sure the lens release tab is fully extended. 2. Insert the lens into Jet Pro’s frame, starting with the side that's closer to you. Insert only one side at a time, and make sure the middle part of the lens is all the way in before you continue.

  • Page 9: Maintenance

    If water or moisture gets on the electrical contacts between the lens and the battery and/or engine, power off Jet Pro, remove the battery and/or engine, and dab the contacts dry with a tissue or soft cloth. Store Jet Pro with the battery and/or engine removed to allow the moisture to dry off.

  • Page 10: Troubleshooting

    WARNING: • Using a Micro-USB cable other than the one provided may shorten battery life and, in some cases, may damage Jet Pro permanently. • Do not attempt to charge Jet Pro with the battery and/or engine removed. This will cause permanent damage.

  • Page 11: Compliance Information

    ICES-003 of the Canadian Department of Communications. equipment generates uses and can radiate radio frequency Jet Pro a été certifié avec le numéro IC 9717A-009. Cet energy and, if not installed and used in accordance with appareil numérique respecte les limites bruits radioélec- the instructions, may cause harmful interference to radio triques applicables aux appareils numériques de Classe B...
  • Page 12 The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Recon Instruments is under license. Other trademarks and trade names are those of their respective owners. WIFI COPY RIGHT INFO...

Table of Contents