DeWalt DWE74911 Original Instructions Manual page 23

2. Place the wheels (b) on the axle (a) and secure
with washers and lock nuts as shown. Tighten
wheel and axle nuts securely.
Attaching the Kickstand (fi g. 5)
Insert the tube plugs (l) into the end of the kickstand
tube. Be sure that the holes (m) in the tube plugs are
in line with the holes (n) in the kickstand tube before
inserting the tube plugs.
Align the kickstand holes with the holes on the
end bracket. Be sure the kickstand is pointing up
when the stand is in an upright position. Secure the
kickstand with the four M8x75 pan head bolts and
nuts provided as shown.
Attaching the Handle (fi g. 6)
Attach the handle with the four M8x75 hex head
bolts provided. Feed the bolts through the handle
feet (h) then through the handle tube and through
the gusset holes on the end bracket. Install four nuts
and tighten securely. NOTE: The handle has two
positions to choose from: a compact position and
an easy carry/setup position.
Table Saw Mounting (fi g. 7, 8)
WARNING: To reduce the risk of
injury, turn unit off, disconnect
machine from power source before
assembling the table saw to the
table saw stand. An accidental start-
up can cause injury.
WARNING: For your own safety,
read and understand the table saw
instruction manual before using. Failure
to heed these warnings may result in
personal injury and serious damage to
the table saw and the accessory.
MOUNTING STEPS FOR THE DWE7491 ONLY (FIG. 1, 8):
1. Place the saw, table side down, on a stable,
non-marring surface.
2. Place the stand on top of saw as shown. Align
the stand holes (j) with the saw frame holes.
3. Feed the M8x75 pan head bolts (r) through
the stand frame then through the saw frame.
Secure with an M8 lock nut from top and
tighten in each of the four hole locations.
4. Lift assembly by stand handle onto kickstand.
MOUNTING STEPS FOR THE DW745 ONLY (FIG. 7):
1. Place the saw, table side down, on a stable,
non-marring surface.
2. Attach the adapter brackets (o) to the saw using
the M6 X 40 pan head bolts, M6 washers,
and M6 lock nuts as shown in figure 7. Do not
tighten fully.
3. Place the stand on top of the saw as shown.
Align the stand holes with the holes in the
adapters.
4. Feed the M8x45 pan head bolts (q) thru the
stand then thru the adapter hole. Secure with
an M8 washers and M8 lock nuts.
5. Tighten all fasteners securely.
6. Lift assembly by stand handle onto kickstand.
WARNING: To reduce the risk of
personal injury, be sure the table saw is
fully anchored on the stand.
WARNING: To reduce the risk of
personal injury, do not hang objects
from the handle. The stand may tip then
downward force is applied.
For additional questions or clarification on the above
instructions, consult an authorised D
agent.
Transporting the Saw on the Stand
(fi g. 9)
COLLAPSING THE STAND FOR TRANSPORT
1. Lifting the stand by the handle, tilt up the stand
until the saw is at a 90 degree angle sitting on
the kickstand.
2. Fold the handle-side legs by depressing the
handle-side leg release levers (c) and rotate until
locking pin clicks into the detent (p). Repeat the
operation on the second handle side leg of the
stand.
3. Fold the wheel-side legs by rotating the
wheel-side leg release levers (d) with foot (or
hand) and rotate until locking pin clicks into the
detent (p). Repeat with other wheel leg.
WARNING: To reduce the risk of
personal injury, DO NOT operate the
table saw mounted to the stand with the
legs folded and the stand sitting on the
ground.
WARNING: Be sure the locking pins
have engaged and the legs are firmly
held in place.
ENGLISH
WALT repair
E
21