Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for UNV DC5301
Summary of Contents for UNV DC5301
- Page 1 Video Decoder Quick Guide Manual Version: V1.00...
- Page 2 Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. Copyright Copyright 2016 Zhejiang Uniview Technologies Co., Ltd. All rights reserved. No part of this manual may be copied, reproduced, translated, or distributed in any form or by any means without prior consent in writing from our company.
- Page 3 contents of this manual are subject to change without prior notice. Update will be added to the new version of this manual. Use of this manual and the product and the subsequent result shall be entirely on the user's own responsibility. In no event shall we be liable for any special, consequential, incidental, or indirect damages, including, among others, damages for loss of business profits, business interruption, or loss of data or documentation, or...
- Page 4 Safety and Compliance Information Safety Symbols The symbols in the following table may be found on installation-related equipment. Be aware of the situations indicated and take necessary safety precautions during equipment installation and maintenance. Symbol Description Generic alarm symbol: To suggest a general safety concern.
- Page 5 This device is a class A product and may cause radio interference. Take measures if necessary. While shipping, the device should be packed in its original packing. Verify that installation is correct. Incorrect cable connection may cause personal injury or device damage. The installation must be made by qualified personnel and should ...
- Page 6 WARNING! Never look at the transmit laser while the power is on. Never look directly at the fiber ports and the fiber cable ends when they are powered on. Use of controls or adjustments to the performance or procedures ...
- Page 7 LVD/EMC Directive This product complies with the European Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC. WEEE Directive–2002/96/EC The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner.
-
Page 8: Table Of Contents
Contents 1 Overview ....................1 Packing List ....................1 Appearance ....................1 LEDs ....................... 2 2 Installation ................... 3 Preparation ....................3 Installing the Dual-SFP Module ..............4 Indoor Installation ..................4 Outdoor Installation ..................5 Cable Connection ..................5 Connecting Cables on the Front Panel .......... -
Page 9: Overview
Overview The video decoder (referred to as device hereafter) is a new-generation network media terminal designed mainly for remote video surveillance. The device can be used with other devices (such as camera) to capture video images and collect audio from a remote location in real time. This guide describes the hardware of the device, how to install it, and how to access it on a web browser. -
Page 10: Leds
Figure 1-1 Front view RS485/422 port LINK LED Ethernet port ACT LED RUN LED Blank filler panel RS232 port USB port Reset button CODEC LED ALM LED Figure 1-2 Rear view CVBS output Alarm input Grounding Grounding Audio output DC power input VGA output HDMI output Two-way audio... -
Page 11: Installation
Description On: The device is operating. Off: The device is shut down. On: A device alarm (e.g., temperature alarm) has occurred. Off: No device alarm. Blinks: The device is decoding. CODEC Off: The device is not decoding. Blinks: The device is transmitting data. Off: The device is not transmitting data. -
Page 12: Installing The Dual-Sfp Module
For outdoor use, check that the above requirements are met, and an outdoor protection box is ready. Installing the Dual-SFP Module CAUTION! Disconnect power before installing the dual-SFP module. Choose a dual-SFP module recommended by your dealer. Loosen the screws and remove the blank filler panel. Then, insert the dual-SFP module and fasten the screws. -
Page 13: Outdoor Installation
Install the device in the rack. Outdoor Installation NOTE! Choose a protection box that meets standards. Please refer to the DVS_DC Cable Connection Guide for details. Use screws to secure the device in the protection box, with ventilation openings facing upward and downward. Keep at least 10 cm free space above and below the ventilation openings to ensure effective heat dissipation. -
Page 14: Connecting Cables On The Front Panel
Connecting Cables on the Front Panel Connect to a device Connect to network with a serial cable with a network cable Network Connecting Cables on the Rear Panel Alarm input device Display device Audio output device Power input Alarm output Display Display device... -
Page 15: Connecting Audio And Alarm Cables
Connecting Audio and Alarm Cables Audio output Alarm input device device ALM IN AUDIO 1 2 3 4 G G O G I G G O 1+ 1- 2+ 2- LINE ALM OUT Alarm output device Power NOTE! The alarm output device shall use a DC power supply, and the voltage and current must not exceed 12 V and 0.7 A. -
Page 16: Verification
Verification WARNING! Installation and cable connection must be completed properly before the device is connected to power. Otherwise, bodily injury or device damage may occur. Verify the following before connecting the device to power: The device is properly installed. The device is grounded properly, and all cables are connected ... - Page 17 NOTE! The default IP address is 192.168.0.14, the default subnet mask is 255.255.255.0, and the default gateway address is 192.168.0.1. Use admin as the username and password for your first login. Change the default password on the User page to ensure security. Follow the steps to log in to the device: Open the IE and then enter the IP address of the device in the address bar.
- Page 18 BOM: 3101C0E9...
Need help?
Do you have a question about the DC5301 and is the answer not in the manual?
Questions and answers