Table of Contents
Advertisement
11lt the Front,
Lift the Back
Then the Back
On
Raise Slgnal
Arm to Stop Ice Maker.
Lower Signal
Arm to Start It.
Adjusting
the Shelves and Meat Pan.
Arrange
your refrigerator
shelves
and meat
pan to suit yourself.
You can
put
two shelves together
to make one full-width
shelf, or put
them on different
levels.
To remove
them,
tilt
up at the front. Then lift up at the back.
When
replacing
them, keep them tilted; guide
the rear hooks into the Slots
in the shelf bracket.
Lowerthe
front.
Before moving
the meat
pan itself, remove
the pan
by pulling
it
out, lifting the front and then pulling
out the rest of the way.
Removing
Non-Adjustable
Shelves.
To remove
a shelf, lift up the front. Then lifl up at the back.
To
replace
it, put the
rear
notches
onto
the
shelf
supports.
Lower
the
front into
place.
Optional
ICE MAGIC"
Automatic
Ice Maker.
If you have the automatic
Ice maker accessory o( plan to add one later
[Part No. ECKMF-6). there are a few things you will want to know
l
The ON; OFF lever is a wire slgnal arm.
Down...for
making
ice automatically,
Up to shut off the Ice maker.
l
Shake the bin occasionally
to keep cubes separated,
and to obtain
Increased
storage capacity
. It IS normal for Ice crescents to be attached
by a corner. They WIII break
apart easily
l
You WII! hear water running when tee maker IS working. You'll hear Ice
fall Into the bin Don't let these sounds bother you
l
The ice maker WIII not operate
until the freezer is cold enough to make
ice This can take overnight
l
Because of new plumbing
connectlons,
the first ice may be dlscolored
or off-flavored,
Discard the ftrst few batches
of ice.
. If ice is not being made fast enough and more Ice IS needed,
turn the
Refrtgerator
Control toward
a higher number. Walt a day and, if nec-
essary, turn the Freezer Control toward A.
l
If you remove the Ice bin, raise the slgnal arm to shut off the ice maker.
When you return the bin, push it all the way In and lower the arm to the
ON posltlon
. If cubes are stored too long, they may develop
an off-flavor.
.like stale
water. Throw them away
They
will
be replaced.
Cubes In the Ice bin
can also become
smaller by evaporation.
Replacing
the Light Bulb.
When the light bulb needs
replacing,
you wtll find you can reach
It easily
without
removing
anythlng
To remove
the light bulb
first
unplug
the refrigerator
Then, reach
behlnd
the control
console
You
can feel the bulb
Remove
It Replace
the bulb with a 40.watt
appll-
ante
Dulb available
from most grocery,
hardware
or variety
stores
Removing
the Crispers
and Crisper
Covers.
To remove the crispers, slide them out until they stop Lift the front a little
and slide them the rest of the way out
Each cover
IS
held IV place
by two pegs at the back and two notched
tabs in the front Press the tabs out of the way to lift the front Lift the back off
the pegs
To put the covers back
replace
the center leg Replace
each cover by
first flttlng the back notches over the pegs Then push the front down Into the
notched
tabs
The center leg can be made shorter or longer to help level the crisper
covers, if necessar\/ Turn the leg clockwtse
to make the leg longer Turn It
counterclcckwlse
to shorten the leg
Push the lab
to Clear
the Cover
5
Advertisement
Table of Contents
