Therefore, the following checks should be performed for the continued protection of the customer and servicetechnician. PDP-434PU...
Page 3
PRODUCT SAFETY NOTICE With the AC plug removed from an AC power source, place a Many electrical and mechanical parts in PIONEER set have jumper across the two plug prongs. Turn the AC power switch on. special safety related characteristics. These are often not evident...
Page 4
43 X DRIVE Assy 43 SCAN X CONNECTOR B Assy A Assy 43 SCAN A Assy X CONNECTOR B Assy Power Cord AC Inlet with Filter Power Switch (S1) Fig.1 Charged Section and High Voltage Generating Point (Rear View) PDP-434PU...
Page 5
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. PDP-434PU...
7.1.6 TEMPERATURE-COMPENSATION FUNCTION OF THE DRIVE-SYSTEM VOLTAGE ...... 7.1.7 POWER ON/OFF FUNCTION FOR THE LARGE-SIGNAL SYSTEM ............. 7.1.8 BACKING UP THE ADJUSTMENT VALUES FOR THE MAIN UNIT ............7.1.9 TROUBLESHOOTING ............................. 7.1.10 DISASSEMBLY ............................... 7.2 IC INFORMATION ..............................8. PANEL FACILITIES AND SPECIFICATIONS ......................PDP-434PU...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING • PDP-434PU / TUCK • PRO-434PU / KUC type • PDP-434PE / WYVI6 •...
Page 9
See Contrast table (2) Pad (PP B- L) AHA2317 Pad (PP B- R) AHA2318 (2) CONTRAST TABLE PDP-434PU/ TUCK, PDP-434PE/ WYVI6, PDP-434PE/ WYVI6XK and PRO-434PU/ KUC are constructed the same except for the following : PDP-434PU PDP-434PE PDP-434PE PRO-434PU Mark No.
Page 19
See Contrast table (2) Terminal Label See Contrast table (2) • • • • • (2) CONTRAST TABLE PDP-434PU/ TUCK, PDP-434PE/ WYVI6, PDP-434PE/ WYVI6XK and PRO-434PU/ KUC are constructed the same except for the following : PDP-434PU PDP-434PE PDP-434PE PRO-434PU Mark No.
Screw APZ30P080FZK Cushion AEB1393 Front Case Assy See Contrast table (2) (2) CONTRAST TABLE PDP-434PU/ TUCK, PDP-434PE/ WYVI6, PDP-434PE/ WYVI6XK and PRO-434PU/ KUC are constructed the same except for the following : PDP-434PU PDP-434PE PDP-434PE PRO-434PU Mark No. Symbol and Description...
BLOCK V+3V_LVDS V+3V_PLL V+ADR V+3V_LVDS V+3V_PLL V+ADR V+3V_IC5 V+3V_IC5 V+9V V+60V V+9V V+60V V+5V V+5V DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC IC1552 IC1553 IC1554 IC1555 IC1552 IC1553 IC1554 IC1555 PDP-434PU...
Page 23
BLOCK V+3V_LVDS V+3V_PLL V+3V_LVDS V+3V_PLL V+ADR V+ADR V+3V_IC5 V+3V_IC5 V+9V V+60V V+9V V+60V V+5V V+5V DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC IC1552 IC1553 IC1554 IC1555 IC1552 IC1553 IC1554 IC1555 PDP-434PU...
Page 27
15 GND 16 HPD Hot plug detection +5VDC 17 RX0- DVI signal DVI differential signal (-) 18 RX0+ DVI signal DVI differential signal (+) − 19 GND − − 20 N.C Not connected − − 21 N.C Not connected PDP-434PU...
Page 28
No. Signal Name I/O Signal Description Voltages at NTSC Signal Input − STBGND 0V DC Key scan signal 0V DC Key scan signal 0V DC Key scan signal +3.3V DC Key scan signal +3.3V DC Key scan signal +3.3V DC PDP-434PU...
Page 29
0-3.3V amplitude square wave 53 BB6 8bit video signal output (BLUE odd number) 0-3.3V amplitude square wave 54 BB7 8bit video signal output (BLUE odd number) 0-3.3V amplitude square wave − 55 GND − 56 GND − Not connected − Not connected PDP-434PU...
Page 30
Connection detecting signal of DVI connector 0VDC 109 SRS SRS function control signal +3.3VDC 110 RSTBTMD TMDS IC reset signal +3.3VDC − 111 MAX_PLS1 Not connected 112 L_SYNC TMDS IC synchronous detecting signal +3.3VDC − 113 MAX_PLS2 Not connected − 114 GND PDP-434PU...
STB_ SW FOCUS TRUBASS VOFS VSUS A_ MUTE LED_ R LED_ G AC_ DET DRIVE_ OFF PD_ TRG RELAY CN4001 POWER SUPPLY ASSY STB_ MT DRIVE RELAY CONTROL STB3.3V Vsus Each Power AC_ DET POW ER ON AC-OFF RELAY Det. PDP-434PU...
Page 32
CN5602 (D2) No. Signal Name I/O Signal Description Voltages at NTSC Signal Input VADR Address drive power (+61V) input +61VDC VADR Address drive power (+61V) input +61VDC Not connected − GND_ADR − GND_ADR +6.5V power input +6.5V +6.8VDC − GND_D PDP-434PU...
+6.5V WOW IC VOLUME IC IC3502 IC3501 R_Audio L_Audio SCL, SDA BUFFER SRS,FOCUS,TRUBASS +9.0V A_Mute ST-BY +16.5V +16.5V A_NG_B REGULATOR POWER AMP IC CN3501 IC3503 IC3504 DC DETECT BLOCK CN3503 J301 HD SP TERMINAL ASSY R OUT L OUT PDP-434PU...
6.2 COMMAND 6.2.1 RS232C COMMAND • The panel control items for the PDP-434PU system can be controlled with the RS-232C commands by connecting a PC through the GGF1475 special communication device when the Media Receiver is not connected with the PDP.
Page 51
Data of hour meter for the eighth latest PD 7 bytes 1st-5th byte: Hour, 6th-7th byte: Minute Data on temperature for the eighth latest PD (TEMP1) 3 bytes 000 - 255 Notes: • Ignore the 2-byte checksum at the end. • For details, see "Description on power-down." PDP-434PU...
Page 52
Reservation 7 bytes 1st-5th byte: Hour, 6th-7th byte: Minute Hour meter Notes: • Ignore the 2-byte checksum at the end. • The data expected to be used for service may be "5. Data on temperature" and "15. Hour meter". PDP-434PU...
Page 53
Abnormality in RST2 (power decrease of DC-DC converter) Volume IC Panel having high temperature Reservation Audio failure (speakers short-circuited) Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation PDP-434PU...
Assy X CONNECTOR B Assy HD AUDIO PANEL IF Assy PANEL LED Assy AMP Assy PANEL IR Assy HD SP 43 ADDRESS Assy TERMINAL Assy 43 ADDRESS Assy 43 ADDRESS Assy 43 ADDRESS Assy KEY CONTROL Assy Rear view PDP-434PU...
Disconnection of the 1.0S 1.0S 1.0S 1.0S system cable GREEN Disconnection of cable Power management when the Media Receiver is not 1.0S 1.0S GREEN connected with the PDP Note: "P" stands for panel. Lit in red Lit in green Not lit PDP-434PU...
Page 56
Immediate power-down 11 times DIGITAL-DCDC Immediate power-down 12 times UNKNOWN ∗ Immediate power-down 15 times ∗ If the unit cannot identify which protection circuit was activated, even if a power-down had been detected, the red LED may flash 15 times. PDP-434PU...
Page 57
5 times Audio failure HD AUDIO Defective AMP IC HD AUDIO AMP ASSY IC3504 Check if the cable is HD AUDIO Disconnection of cable CN4009 - CN3501 disconnected or not securely connected. PDP-434PU...
Page 58
• Block diagram of the power-down signal system PDP-434PU...
• Diagnosis with the aid of Factory mode When the Media Receiver is connected, the power-down and shutdown logs can be referred to with OSD. Only the items useful when servicing the PDP-434PU/PDP-504PU are described here. How to enter Factory mode using the remote control unit Please refer to the technical documentation (Service knowhow).
Page 61
Data on temperature (INFORMATION-TEMPERATURE) The data on the current temperatures are displayed. The temperature at the PANEL SENSOR ASSY of the PDP-434PU/PDP-504PU is indicated as the TEMP 1 value (000-255), which should be converted using the following formula: 0.65 × TEMP 1 value - 52 Current temperature (°C)
Then enter the Factory mode. Press the MUTE key four times, then hold the OSD key pressed for at least 3 seconds. Set the AC switch on the panel to OFF. The log is also cleared. Then set the drive ON/OFF switch to ON. Rear View TRAP switch Fig. TRAP switch PDP-434PU...
Purpose: For improving the yield by compensating for the temperature characteristics of the panel Note: Temperature compensation is performed only for the VSUS voltage, and not for the VOFS voltage. This compensation is controlled by the software. PDP-434PU...
• If the slide switch is set from OFF to ON while the power is on, a power-down will occur. Be sure to turn the power off before switching the slide switch. S5201 Drive OFF Normal position Rear View DIGITAL VIDEO Assy Fig. Drive OFF switch PDP-434PU...
DIGITAL VIDEO Assy will be copied to Area B of the PANEL IF Assy of Unit 2, overwriting the data necessary for Unit 2. Once overwritten, the original data will not be restored. PDP-434PU...
Page 67
7 Change the keyword for the DIGITAL VIDEO Assy to "adjusted" by sending the "FAJ" RS232C command. Note: Use a Minolta CA-100 color difference meter or the equivalent for measurement. Otherwise, the specifications of the product cannot be assured. PDP-434PU...
As the screws used for the front case are B tight (ABZ30P100FZK) and other screws used are M screws (AMZ30P060FZK), care must be taken not to use the screws in the wrong places. Front case (43P) PANEL KEY Assy PDP-434PU...
Page 70
PANEL LED Assy may be damaged. Front chassis VR Assy (43) Remove the switch holder, by removing the screw (M screw). Remove the thin clamp, then remove the wires. Remove the front chassis VR Assy (43), by removing the 4 screws (M screws). PDP-434PU...
Page 71
• PCB Location for multi base section HD AUDIO AMP Assy Remove the 6 screws (M screws). Remove the X CONNECTOR A and B Assemblies. PANEL IF Assy HD SP TERMINAL Assy X CONNECTOR A Assy 43 X DRIVE Assy X CONNECTOR B Assy PDP-434PU...
Page 73
BA8274F (PANEL IF ASSY: IC4206) • I C Bus Interface IC Block Diagram N.C. Buffer Buffer N.C. Pin Function Pin No. Equivalent Circuit Pin Function Name Buffer output 35.7 Buffer input 35.7 Ground Power supply PDP-434PU...
Page 77
Pin Function Equivalent Circuit Name SDIP42 SOP40 QFP48 FFR2 V+/2 FFL2 V+/2 VREF FIL1 V+/2 VREF PDP-434PU...
Page 78
Block Diagram to DQ Erase Voltage Input/Output Generator Buffers State Control BYTE Command Register Program Voltage Generator Chip Enable Data Latch Output Enable Logic Y-Gating Y-Decoder Timer for Address Low V Detector Program/Erase Latch X-Decoder Cell Matrix to A PDP-434PU...
Page 79
HDCP HDCP -------------- Decryption Keys Configuration Logic Engine E EPROM SCLS Slave SDAS CTL3 QE[23:0] RXC ± PanelLink QO[23:0] Panel TMDS RX0± Mask ODCK encrypted unencrypted Interface Digital RX1± data data Logic Core RX2± HSYNC control VSYNC EXT_RES SCDT PDP-434PU...
Page 81
BIAS OVER VOLTAGE / CIRCUIT SURGE PROTECTOR V CC STANDBY THERMAL OUTPUT PIN TO GND SHUT DOWN SHORT PROTECTOR PREDRIVER POWER LOAD SHORT POWER PROTECTOR GND2 PREDRIVER POWER OUTPUT PIN TO V CC SHORT PROTECTOR POP NOISE PREVENTION CIRCUIT PDP-434PU...
Page 82
Setting pin for flash rewriting mode (pull-up) PSIZE Panel size distinction B_SCL IIC clock output for backup EEPROM B_SDA IIC DATA I/O for backup EEPROM ADR_PD PD signal of address junction LED_G Green LED control LED_R Red LED control PDP-434PU...
Page 83
[A/D] Operation mode setting − − AVSS GND for A/D input MODEL [A/D] CMX/HD/TV/WX distinction − − VREF Reference voltage for A/D input − − AVCC Power supply for A/D input = STB3.3V NC pin NC pin AMG_MD Address emergency monitor PDP-434PU...
Page 84
Address LVDS signal output AF19 AD0TXOUT3M Address LVDS signal output AF20 AD0TXCLKOUTM Address LVDS signal output AF21 AD0TXOUT2M Address LVDS signal output AF22 AD0TXOUT1M Address LVDS signal output AF23 AD0TXOUT0M Address LVDS signal output AF24 VSSL15 AF25 AD4TXOUT3P Address LVDS signal output PDP-434PU...
Page 85
B phase signal input of B video (0 bit) VD signal input RAI_5 A phase signal input of R video (fifth bit) DCLKI CLK input GAI_4 A phase signal input of G video (fourth bit) BAI_9 A phase signal input of B video (ninth bit) PDP-434PU...
Page 86
Address LVDS signal output AE22 AD0TXOUT1P Address LVDS signal output AE23 AD0TXOUT0P Address LVDS signal output AE24 VSSL15 AE25 AD4TXCLKOUTP Address LVDS signal output AD25 AD4TXOUT2P Address LVDS signal output AC25 AD4TXOUT1P Address LVDS signal output AB25 AD4TXOUT0P Address LVDS signal output PDP-434PU...
Page 87
3.3V power supply GAI_1 A phase signal input of G video (first bit) GAI_0 A phase signal input of G video (0 bit) NC pin XSUSB_14 X-Drive control signal output VDDIO 3.3V power supply XSUSB_8 X-Drive control signal output PDP-434PU...
Page 88
VSSLA VSSLA VSSLA SDITDO JTAG signal GPIO0_7 Microcomputer macro general-purpose port VDDIO 3.3V power supply YSUSA_0 Y-Drive control signal output YSUSA_6 Y-Drive control signal output YSUSA_12 Y-Drive control signal output YSUSB_0 Y-Drive control signal output VDDD33 3.3V power supply PDP-434PU...
Page 89
3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply PDP-434PU...
Page 90
B phase signal input of G video (ninth bit) GBI_5 B phase signal input of G video (fifth bit) BBI_9 B phase signal input of B video (ninth bit) BBI_3 B phase signal input of B video (tenth bit) PDP-434PU...
Page 91
VSSLA AB21 VSSLA AB22 VSSLA AA22 VDDLA 3.3V power supply VSSL15 VSSLA VSSLA VSSL15 SDITMS JTAG signal GPIO0_5 Microcomputer macro general-purpose port VSS15 YSUSA_2 Y-Drive control signal output YSUSA_8 Y-Drive control signal output VSSD15 YSUSB_2 Y-Drive control signal output PDP-434PU...
Page 92
VDDLA 3.3V power supply AA13 VDDLA 3.3V power supply AA14 VDDLA 3.3V power supply AA15 VDDLA 3.3V power supply AA16 VDDL15 1.5V power supply AA17 VDDLA 3.3V power supply AA18 VDDLA 3.3V power supply AA19 VDDL15 1.5V power supply PDP-434PU...
Page 93
B phase signal input of R video (first bit) VDD15 1.5V power supply GBI_3 B phase signal input of G video (third bit) BBI_7 B phase signal input of B video (seventh bit) BBI_1 B phase signal input of B video (first bit) VDD15 1.5V power supply PDP-434PU...