Service Manual TOP NEXT Order No. MTV0308268C3 Colour Television TX-29PS62Z GP3 Chassis Specification Power Source AC Auto 110-240 V, 50/60 Hz Power Consumption 129 W Standby condition : 2 W Aerial Terminal Impedance : 75Ω, Coaxial type Tuning System Frequency Synthesizer...
4 Market Mode Function TOP PREVIOUS NEXT Outline: MPU controls the functions switching for each ICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Market Mode. 1. Selection of Market Mode Adjust the VOLUME “zero”...
Page 3
5.1 B VOLTAGE TOP PREVIOUS NEXT Item/Preparation Adjustment Procedure Operate the TV set. Confirm that the indicated test points for the specified voltage: TPA 10 : 141 ± 1.50V Set controls : (MARKET MODE CHK 2) TPA 8 : 8 ± 1.0V Bright .....
Page 4
5.2 RF AGC TOP PREVIOUS NEXT Item/Preparation Adjustment Procedure Receive a colour bar pattern. Set RF AGC Control such as to procedure a snowy picture. Set the input level to 69 (+1.2) db. Set RF AGC Control at the point just before the voltage at AGC : TPA 15 begins to drop. (75Ω...
5.3 HIGH VOLTAGE TOP PREVIOUS NEXT Item/Preparation Adjustment Procedure Operate the TV set. Connect a DC voltage meter to D850 cathode and confirm the voltage is 141.0 ± 2.0V. Connect a high voltage meter (Electrostatic Type) to an anode of the picture tube. Receive the crosshatch pattern.
Page 6
5.4 SUB TINT TOP PREVIOUS NEXT Item/Preparation Adjustment Procedure Receive a 3.58 MHz NTSC rainbow pattern Adjust Sub NTSC Tint so that the peak of level of waveform is similar to Fig. 3 Connect oscilloscope to A21 pin 6. Receive the Rainbow pattern (3.58 MHz NTSC) on both of Main and Sub pictures. Set controls: Adjust Sub NTSC Tint 2 so that the peak of level of 1.3 ±...
5.5 SUB CONTRAST TOP PREVIOUS NEXT Item/Preparation Adjustment Procedure Receive a colour bar pattern. Adjust Bright Colour: Y = 1.0 ± 0.4Vp-p Connect an oscilloscope to TPA37 or TPL2 (G OUT). Adjust Sub Contrast Colour: Connect a short jumper to FBT pin3 or TPA 34 and TPA 5.. b = 2.7 ±...
Page 8
5.6 PAL COLOUR OUTPUT TOP PREVIOUS NEXT Item/Preparation Adjustment Procedure Receive PAL colour bar pattern. Adjust Bright Control. a = 2.3 ± 0.5Vp-p Connect an oscilloscope probe to TPL2 (G OUT). Adjust Sub Colour control. Connect a short jumper to FBT pin 3 or TPA34 and TPA5. Connect the oscilloscope probe to TPA40.
Page 9
5.7 NTSC COLOUR OUTPUT TOP PREVIOUS NEXT Item/Preparation Adjustment Procedure Apply 3.58MHz NTSC Rainbow pattern. Adjust Bright Control. a = 2.3 ± 0.2Vp-p Connect an oscilloscope to TPA36 or TPL1 (R OUT). Connect the waveform. b = 1.3 ± 0.5Vp-p CHK2 and press digit key “5”...
5.8 COLOUR PURITY TOP PREVIOUS NEXT 1. Set Bright and Contrast controls to their maximum positions. 2. Operate the TV set over 60 minutes. 3. Full degauss the picture tube by using an external degaussing coil. By rotating R-B static convergence magnet.
Page 11
5.9 CONVERGENCE TOP PREVIOUS NEXT 1. Apply a crosshatch pattern signal and set Contrast control to the maximum position. 2. Adjust Bright control to obtain a clear pattern. 3. Adjust Red and Blue line at center of the screen. 4. Adjust Red and Blue with Green line at center of the screen by rotating (RB)-G static convergence magnet.
Page 12
5.10 WHITE BALANCE (MARKET MODE CHK 3) TOP PREVIOUS NEXT Preparation 1. Receive a colour bar signal with colour “OFF”, and operate the TV set for more than 30 minutes. 2. Set the picture menu to “DYNAMIC NORMAL” and the AI to off. 3.
Page 13
Fig. 1 3. Slowly turn the screen control clockwise until a green colour horizontal line appears on the picture tube. This is the setting point for the screen control. Note: Do not adjust the G-CUTOFF setting in the following procedure. 4.