1. Manuals
  2. Brands
  3. Aigis Mechtronics Manuals
  4. Digital Camera
  5. HS9384-2H
  6. Installation and operating instruction

Aigis Mechtronics HS9384-2H Installation And Operating Instruction

Outdoor camera housings hs9384 series
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
O
C
H
UTDOOR
AMERA
OUSINGS
HS9384 S
ERIES
I
O
I
N S T A L L A T I O N A N D
P E R A T I N G
N S T R U C T I O N S

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HS9384-2H and is the answer not in the manual?

Questions and answers

Related Manuals for Aigis Mechtronics HS9384-2H

Summary of Contents for Aigis Mechtronics HS9384-2H

  • Page 1 UTDOOR AMERA OUSINGS HS9384 S ERIES N S T A L L A T I O N A N D P E R A T I N G N S T R U C T I O N S...

  • Page 2: Safety Precautions

    Aigis Mechtronics for return authorization and ship- 20. Lightning - For added protection of this unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and dis- ping instructions.

  • Page 3: Installation

    Outside diameter between 4.3 mm Maximum Camera/Lens Size: HS9384-2H: Accepts cameras up to 64 W x 54 H mm (0.170 in) & 11.9 mm (0.470 in) (2.5 x 2.1 in), lenses up to 67 W x 75 H mm (2.6 x 2.9 in), and camera/lens combinations up to 355 mm (14.0 in).

  • Page 4: Cradle Removal

    1.2 Zoom Lens Cameras: Allow 3/16-inch (5 mm) clearance Cable Type: Jacketed multiconductor cable Lens Control Cable from the front face of the lens to the front faceplate of the cradle during the camera/lens assembly. This clearance Cable Size: Outside diameter between 4.3 mm provides the necessary space for the lens to extend out- (0.170 in) &...

  • Page 5: Power Connections

    If a sealant is to be used, be sure it is a neutral cure type. Sealants that release acetic acid may harm camera electronics. If it is necessary to use a PG type conduit, an NPT to PG conversion kit (HS9384NPT) can be purchased separately. M4 Screw Use of drip loops is recommended on the wiring outside of the rear end cap.
  • Page 6 Installing a 24 volt camera into the HS9384-5H housing For 24 volt cameras: utilizes the internal transformer for camera power (see The HS9384-2H housings are designed to be used with 24 volt cameras only. Figure 10). Connect the supply (230 VAC) to the Wago connectors Connect the supply (24 VAC) to the unoccupied sides of (provided).

  • Page 7: Video Coax Connection

    5.7 Video Coax Connection WARNING: Only use the cables specified under INSTALLATION, Cable Requirements for wiring of the video coax connection. Front Face Install the seal cap portion of the large liquid tight fitting on the video coax cable and pull the cable through the right fitting on the rear end of the cradle.

  • Page 8: Cradle Assembly

    To rotate the cradle assembly (while mounted), grasp the rear handle and rotate to the desired position. View the monitor while rotating. Figure 15 Inserting Cradle Assembly ©2010 Aigis Mechtronics 1124 Louise Road, Winston-Salem, NC 27107-5450 100 0023 002 AIG 1/10 Tel: 336.785.7740 Fax: 336.785.7744...

This manual is also suitable for:

Hs9384-2h-9Hs9384-5hHs9384-6h

Table of Contents