Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Kelvinator KSE362HPCA
Summary of Contents for Kelvinator KSE362HPCA
- Page 1 Heat Pump Hot Water System Installation Manual...
-
Page 2: Table Of Contents
If you wish to dispose of an old hot water system, please • by clients in hotels, motels and other residential type contact your local authorities and ask for the correct environments. method of disposal. • bed and breakfast type environments 2 contents Kelvinator heat pump hot water system... -
Page 3: Important Safety Instructions
The temperature settings for the heat pump and auxiliary boost heater are factory pre-set to ensure optimum energy efficiency whilst providing Legionella bacteria protection. The temperature settings are therefore not adjustable by the customer or installer. Kelvinator heat pump hot water system important safety instructions 3... -
Page 4: Heat Pump Specifications
15°C, water inlet temperature of the units is 15°C , water outlet water outlet temperature is 35°C. temperature is 55°C. For more specific heat pump dimensions and safe installation distances refer to page 8 of this manual. 4 heat pump specifications Kelvinator heat pump hot water system... -
Page 5: Storage Tank Specifications
Net weight (kg) Tank wall thickness (mm) Element rating (kW) T/P relief valve pressure limit (kPa) T/P relief valve temperature limit (°C) T/P relief valve energy release rate (kW) Full weight (kg) Kelvinator heat pump hot water system storage tank specifications 5... -
Page 6: Components
Temperature and Pressure relief valve 1/2" Male NOTE: The item numbers used in the table refer to the numbers used in the installation diagram located in the middle of this manual (pages 12 and 13) 6 components Kelvinator heat pump hot water system... - Page 7 High performance tempering valve 50°C NOTE: The item numbers used in the table refer to the numbers used in the installation diagram located in the middle of this manual (pages 12 and 13) Kelvinator heat pump hot water system components 7...
-
Page 8: Installation
NOTE: All measurements are in mm. For specific dimensions of the storage tank and its connections refer to page 5 of this manual. 1500 NOTE: All measurements are in mm. 8 installation Kelvinator heat pump hot water system... - Page 9 If in doubt, consult your plumber. and non (700kPa) valve return (600kPa) drain valve Kelvinator heat pump hot water system installation 9...
- Page 10 The outlet of the drainage the heat pump outlet connection. piping must be left open to the atmosphere at all times, and installed in a frost free environment. return outlet relief valve 10 installation Kelvinator heat pump hot water system...
- Page 11 Open the nearest hot tap or fixture to the hot water system. Once water is flowing freely from the hot tap or fixture, indicating that all air has been dispelled from the hot water system, close the hot tap or fixture. Kelvinator heat pump hot water system installation 11...
-
Page 12: Installation Diagram
Installation of this hot water system must be completed by an authorised and licensed person in accordance with all local regulations, including AS3500 plumbing and drainage requirements and AS3000 electrical wiring standards. 12 installation diagram Kelvinator heat pump hot water system... - Page 13 Note: terminal block may differ return slightly depending on model. return inlet flow flow drain Kelvinator heat pump hot water system installation diagram 13...
-
Page 14: Electrical Connection
220-240V~ 50Hz connect to off-peak or continuous supply common earth terminal heater line output HN continuous supply input 220-240V~ 50Hz 14 electrical connection Kelvinator heat pump hot water system 14 electrical connection Kelvinator heat pump hot water systems... - Page 15 Electric heating manual mode and powering the 3.6kW element in the storage tank. Off peak wiring configuration 1. active (red) neutral (black) earth green/yellow continuous supply input storage tank heater output off peak supply input Kelvinator heat pump hot water system electrical connection...
- Page 16 16 electrical connection Kelvinator heat pump hot water systems...
-
Page 17: Temperature Sensor Connection
Inside the heat pump’s terminal box is a female plug socket that the male plug end of the sensor cable plugs into. Push the male plug into the female socket until it clicks into place. return Kelvinator heat pump hot water system temperature sensor connection 17... -
Page 18: Commissioning
"force" and "query" on the printed circuit board. The circulating pump should start and after one minute the heat pump will begin to operate. 18 commissioning Kelvinator heat pump hot water system... -
Page 19: Warranty
New Zealand state spare parts centre in New Zealand FREE CAll 0800 10 66 10 FREE CAll 0800 10 66 20 ELECTROLUX (NZ) Limited www.electrolux.co.nz (New Zealand only) (New Zealand only) KHWS_Warr_Aug13 Kelvinator heat pump hot water system warranty 19... - Page 20 Customer Care team or visit our website. telephone: 13 62 26 email: hotwatersystems@electrolux.com.au web: kelvinator.com.au Kelvinator. We are part of the Electrolux family. Share more of our thinking at electrolux.com.au P/No. KHWHPI/2 © 2015 Electrolux Home Products Pty Ltd ABN 51 004 762 341 KMAN_KHWHPIM_Oct15...