Usb Devices - JVC KW-AV51 Installation & Connection Manual

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the wiring harness and those of the connector from the car body may be different in color.
1
Connect the colored leads of the wiring harness in the order specified in the illustration below.
2
Connect the antenna cord.
3
Finally connect the wiring harness to the unit.
Antenna
terminal
* 1
2
Rear ground
terminal
White with black stripe
A
Connecting to the steering wheel remote controller
If your car is equipped with the steering wheel remote controller, you can operate this unit using the
controller. For connection, an exclusive remote adapter (not supplied) which matches your car is
required. For details, consult the same car audio dealer as where the unit is purchased.
KW-AV61BT
KW-AV51
B
Connecting the external amplifiers and subwoofer
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, and connect them to the amplifier. Leave the
speaker leads of this unit unused.
• You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to
get clear sounds and to prevent internal heat built-up inside the unit.
See page 43 of the INSTRUCTION MANUAL.
To the remote lead of other equipment
* 2 Y-connector
Remote lead
Remote lead (blue
Front
with white stripe)
speakers
JVC *
6
Amplifier
*
7
C
Connecting the microphone (Only for KW-AV61BT)
1
2
Microphone
Adhesive
tape
KW-AV61BT
D
Connecting the Bluetooth adapter (Only for KW-AV51)
KS-BTA100
KW-AV51
* 6
See page 58 of the INSTRUCTION MANUAL.
Light green
(See page 1)
Fan
10 A fuse
8
White Gray with black stripe
Left speaker
(front)
2 5
OE remote adapter * *
Steering wheel remote controller (equipped in the car)
* 6
* 2
*
6
KW-AV61BT/KW-AV51
3
To the blue with white
Blue with white stripe
*2
stripe lead of the supplied
wiring harness 5
Ground
Black
To the brown lead of the
supplied wiring harness 7
Brown
Not used
Extension wire (supplied)
3
Black 1
To metallic body or chassis of the car
3
Yellow *
2
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
3
Red
Blue
Blue with white stripe
Orange with white stripe
Brown
Light blue with yellow stripe
Gray Green with black stripe
Right speaker
(front)
E
Connecting an external navigation unit
Connect an external navigation unit to the RGB
input terminal. The positional information detected
on the touch panel and picture signals from the
navigation unit are transferred through the terminal.
Refer to the manual of the external navigation unit
for details.
• Please contact your dealer to inquire about compatible navigation units.
• JVC cannot guarantee proper operation of the external devices connected to the RGB input terminal.
F
Connecting the external components
Camcorder
etc.

USB devices

JVC Amplifier
* 7
Subwoofer
USB cable (approx. 1 m)
Rear
speakers
KW-AV61BT
KW-AV51
JVC
Amplifier
• To watch video, connect the iPod/iPhone using JVC KS-U30
* 7
video is not displayed on the screen.
• To listen to music, connect the iPod/iPhone using a USB 2.0 cable (accessory of the iPod/iPhone).
* 1 Only for KW-AV61BT.
* 2 Not supplied for this unit.
* 3 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power
cannot be turned on. Do not connect the lead directly to the battery.
Secure the
* 4 Do not connect the lead to any device other than the OE remote adapter. Doing so may cause malfunction.
microphone
* 5 Alter the wire of the OE remote adapter to connect to the steering wheel remote lead.
cord using
* 6 Audio cord (not supplied for this unit).
cord clamps
* 7 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint
(not supplied)
(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.
if necessary.
* 8 Video cord (not supplied for this unit).
* 9 KV-CM10 / KV-CM20 is not sold in some areas. For details, consult your JVC car audio dealer.
* 10 When using the cable, you need to change the setting on the unit (see page 25 of the INSTRUCTION
MANUAL).
2
The terminals and cables of all models are shown in the
illustration for the purpose of explanation.
1
* 2
* 2
To an accessory terminal in the fuse block
4
To automatic antenna if any (250 mA max.)
5
To the remote lead of other equipment (200 mA max.)
6
To car light control switch
7
Connecting the Bluetooth adapter (Only for KW-AV51)
To the OE remote adapter * 4
Green Purple with black stripe
Left speaker
(rear)
External
navigation
2
unit *
KW-AV61BT
*
8
*
6
Connecting the iPod or the iPhone
USB 2.0 cable (accessory of the
USB device
KW-AV61BT/KW-AV51
See each diagram below.
To parking brake (see page 1)
Ignition switch
Fuse block
Purple
Right speaker
(rear)
RGB input terminal
KW-AV61BT
KW-AV51
KV-CM10/KV-CM20 * *
2 9
Rear view camera
KW-AV51
* 8
External
monitor
iPod/iPhone)
KS-U30
(not supplied)
*10 (separately purchased), otherwise,