Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vicon VICOAX V1961VCR-1
Summary of Contents for Vicon VICOAX V1961VCR-1
- Page 1 X356 MODEL V1961VCR-1 AND V1961VCR-2 Ò VICOAX RECEIVERS VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788-9633 TELEPHONE: 516-952-CCTV (2288) FACSIMILE: 516-951-CCTV (2288) TOLL FREE: 1-800-645-9116 UK: 44/(0) 1489-566300 INFOFAX: 1-800-287-1207...
- Page 3 V1961VCR-1 AND V1961VCR-2 Vicoax Receivers Copyright © 1998 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. Vicon Part No. 8006-8356-05-00 Section 10 Rev 598...
- Page 5 We stand behind the quality and dependability of every product with an industry leading Beneficial Use warranty. If you are not satisfied with a Vicon product or service, I would like to know. Your complete satisfaction is the mission of every Vicon employee.
-
Page 7: Fcc Notice
FCC Notice Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference to radio and television reception. -
Page 9: Table Of Contents
Contents Introduction......................... 1 Installation .......................... 3 Unpacking and Inspection ..........................3 Inspection for Visible Damage........................3 Inspection for Concealed Damage....................... 3 Installation Preparation ..........................3 Installing and Wiring the Receiver ....................... 4 Operation ..........................7 Maintenance........................9 Printed Circuit Boards........................... 9 Fuse Replacement ............................ - Page 10 List of Figures Figure 1 Cable Entry Location ............................4 Figure 2 Location of Adjustable and Replaceable Parts ....................5 Figure 3 Location of Jumpers............................6 ii • • • • List of Figures X356 Rev 598 V1961VCR-1 and V1961VCR-2 Vicoax Receivers...
-
Page 11: Important Safeguards
Use only with a mounting accessory recommended by Vicon, or sold with the video product. Any mounting of the video product should follow Vicon’s instructions, and a mounting accessory recommended by Vicon should be used. - Page 12 This prevents damage to the video product due replacement parts specified by Vicon or that have the to lightning and power-line surges. same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other 15.
-
Page 13: Introduction
Introduction The information in this instruction manual covers the installation and maintenance of the V1961VCR-1 and V1961VCR-2 Vicoax receivers. Throughout this manual, the term V1961VCR refers to all models unless otherwise stated. This unit should only be installed by a qualified technician using approved materials and wiring practices in accordance with national, state, and local wiring codes. -
Page 15: Installation
Installation Unpacking and Inspection All Vicon equipment is tested and inspected before leaving the factory. It is the carrier’s responsibility to deliver the equipment in the same condition as it left the factory. Inspection for Visible Damage Immediately inspect the cartons upon delivery. On all copies of the carrier’s freight bill, make a note of any visible damage. -
Page 16: Installing And Wiring The Receiver
Installing and Wiring the Receiver 1. Mount the receiver box to a wall, or other vertical structure, near the camera to be controlled. The maximum operating distance between the receiver and the camera station is determined by the particular pan-and-tilt drive and motorized lens. Refer to the instruction manuals for the motorized lens and pan- and-tilt units to establish this distance. - Page 17 Figure 2 Location of Adjustable and Replaceable Parts 8. Connect a video cable from the camera video out to one of the two receiver video connectors. Figure 1. 9. Connect a video cable from the transmitter video in to the remaining receiver video connector. Figure 1.
- Page 18 Figure 3 Location of Jumpers 6 • • • • Installation X356 Rev 598 V1961VCR-1 and V1961VCR-2 Vicoax Receivers...
-
Page 19: Operation
Operation The Vicoax Control System is operated by the transmitter. Refer to the instruction manual for the transmitter operating instructions. Operation • • • • 7 X356 Rev 598 V1961VCR-1 and V1961VCR-2 Vicoax Receivers... -
Page 21: Maintenance
Maintenance The V1961VCR receiver requires no routine maintenance. It will provide extended, trouble-free service under normal operating conditions. External equipment and cabling should be checked before troubleshooting the receiver in the event of a system failure. Repairs should only be attempted by qualified personnel in an adequately equipped facility. -
Page 22: Shipping Instructions
Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. -
Page 23: Reference
CAUTION: Careful selection of the proper cable is essential to obtain the best performance from this equipment. Vicon assumes no responsibility for poor performance when cables other than those recommended are installed. In all cases, coaxial cable impedance should be 75 ohms. -
Page 24: Technical Information
Maximum Relay Contact Rating: 5 A at 30 VDC. Connectors: Pan/Tilt/Lens: Vicon part no. 8000-9584-00. Four compression fittings. Video: two UHF threaded, loop-through. Line Cord: Weatherproof gland with strain relief bushing. Fuses: Refer to Table 1. - Page 25 MECHANICAL Overall Dimensions (maximum): Height: 5.75 in. (14.6 cm). Width: 11.0 in. (28.0 cm). Depth: 14.5 in. (36.8 cm). Weight (maximum): 17.8 lb (8.1 kg). Construction: Steel enclosure. Hinged gasketed access door, stainless steel screws. Finish: White, weather resistant enamel. Mounting: Four 0.312-in.
Need help?
Do you have a question about the VICOAX V1961VCR-1 and is the answer not in the manual?
Questions and answers