Nikon D60 Repair Manual
  1. Manuals
  2. Brands
  3. Nikon Manuals
  4. Digital Camera
  5. D60
  6. Repair manual

Nikon D60 Repair Manual

Hide thumbs Also See for D60:
Table of Contents

Advertisement

Quick Links

See also: User Manual , Manual
logo_Q0650_forGraphic
071004_Gdesign_ito
Printed in Japan Feb 2008
REPAIR MANUAL
Copyright© 2008 by NIKON CORPORATION.
All Rights Reserved.
無断転載を禁ず！！
VBA21001-R.3753.A
作成承認印
VBA21001
INC
配布許可印
サービス
計画課
Ｍ

Advertisement

Table of Contents
loading

Related Manuals for Nikon D60

Summary of Contents for Nikon D60

  • Page 1 VBA21001-R.3753.A 作成承認印 配布許可印 サービス 計画課 Ｍ VBA21001 logo_Q0650_forGraphic 071004_Gdesign_ito REPAIR MANUAL Copyright© 2008 by NIKON CORPORATION. All Rights Reserved. 無断転載を禁ず！！ Printed in Japan Feb 2008...
  • Page 2 VBA21001-R.3753.A Points to notice for Disassembly / Assembly WARNING 警告 Due to an internal high voltage area, take extra care not to get 内部に高電圧部あり。カバーを外す時は感電に注意すること。 an electric shock when detaching covers. カバーを外した後は、修理指針の指示に従ってメインコンデン After removing covers, b e sure to discharge the main condenser according to the instructions of repair manuals .
  • Page 3 VBA21001-R.3753.A Disassembly 1. Separation of Front and Rear Bodies Bottom Cover ・ Take out the four screws (#5735) #5674×2 and five screws (#5674). #5674 ・ Open the power-wire lid. Open the power-wire lid. #5674 ・ Remove the bottom cover. #5735 Power-wire lid Bottom cover #5735...
  • Page 4 VBA21001-R.3753.A Rear cover #402 #403 #5424 #6401-3 #5425 #5426 #5427 #421 #425-2×2 #426-1 #405×2 #404×2 #5429 #448 #423 #408 #753 #1016 #5418 #1037 #451×2 #5412 #1017 #410 #406-2 #413 #414 #670×3 #409-1 #452 #453 #750 #B5431 #5431 #630×3 #407 △ (Addition) #433 Remove the only below parts of thermal caulking.
  • Page 5 VBA21001-R.3753.A SB pop-up ・Cut the tracing film sheet, etc into the below size of piece. Then insert it into the clearance of the top cover pop-up part as shown right, and raise the SB by sliding the sheet in the direction of the arrow. Approx.
  • Page 6 VBA21001-R.3753.A Discharge of Main condenser ・Discharge the main condenser from its both ends. Be careful so that the top cover does NOT touch the discharge tool. 2KΩ/5W Main condenser TOGO PCB unit / Loft PCB ・ Disconnect the six FPCs and harness from the connector. ・...
  • Page 7 VBA21001-R.3753.A ・Disconnect the TOGO-PCB unit (#B2001) from the connector, (while pressing the loft-PCB). ・Disconnect the two FPCs from each connector. ・Unsolder the eight wires. ・Remove the loft-PCB that is partially attached with the adhesive double-coated tape. Yellow:DC/DC Adhesive double-coated tape (attached on back of loft-PCB Red:DC/DC Blue:DC/DC...
  • Page 8 VBA21001-R.3753.A SB PCB ・ Unsolder the four wires (connected Orange: Top cover from Top cover). White: Top cover Gray: Top cover Black: Top cover DC/DC PCB unit ・Unsolder the wire (connected from Top cover). Black: Top cover Top cover ・Take out the two screws (#5737). ・Take out the two screws (#635).
  • Page 9 VBA21001-R.3753.A Disassembly of Top cover SB upper case 　・ Press "Pop-up lever A part" and raise the built-in SB. Pop-up lever A part 　・ Take out two screws (#632). #632×2 ・Release the two claws. House the built-in SB and remove the SB upper case (#5301). SB upper case (#5301) Claw - Ｄ...
  • Page 10 VBA21001-R.3753.A Top cover FPC / Wiring ・Remove the tape (#956). ・Unsolder the seven wires (connected from SB lower case unit and SB release base unit). ・Remove the five solder bridges. #956 Red: SB lower case unit Blue: SB lower case unit Green: SB lower case unit Red: SB release base unit Black: SB lower case unit...
  • Page 11 VBA21001-R.3753.A Release button unit / buttons / other small parts ・Remove the rubber SW (#382), and two buttons (#5381,#6384). ・Take out the two screws (#605), and remove [#348], [#347] and the release button unit (#B5350). #B5350 #6384 #5381 #382 #347 #348 #605×2 ・Take out the screw (#650), and release the wire from the boss.
  • Page 12 VBA21001-R.3753.A SB lower case unit ・Remove [#308], while releasing the two hooks. ・ While pressing the SB case rotating shaft (#306), take out the screw (#733) and remove the SB-up spring (#305). ・While watching the wires, remove the SB lower case unit (#B2302). #733 #305 #B2302...
  • Page 13 VBA21001-R.3753.A Top cover FPC unit ・Remove the three solder bridges. ・Take out the two screws (#635) and remove the top cover FPC unit (#B2007-1). #635×2 Soldering bridge×3 #956 #B2007-1 C/D unit / buttons / other small parts ・Remove the AF/AE lock button (#5386) and [#387]. ・Take out the two screws (#635), and remove the C/D unit (#B367).
  • Page 14 VBA21001-R.3753.A Mode dial unit ・Take out the screw (#640), and remove [#372], [#373], [#6371-2],[#461-1] and [#460-1]. #460-1 #461-1 #6371-2 #373 #372 #640 Shoe base ・Take out the four screws (#654), remove [#322], [#318], shoe base (#316) and [#B317]. #318 #316 #B317 #311×2 #322...
  • Page 15 VBA21001-R.3753.A SB PCB ・Unsolder the two wires (connected from Relay-PCB). Red: Relay-PCB Black: Relay-PCB DC/DC PCB ・Unsolder the two wires (connected from Mount GND plate and Front body FPC). Black: Mount GND plate Black: Front body FPC Bottom base plate unit ・Take out the five screws (#616).
  • Page 16 VBA21001-R.3753.A Separation of Front and Rear bodies ・Take out the four screws (#624). ・Separate the front body from the rear body. Caution: Separate them slowly so as NOT to cut the two wires of the relay-PCB that pass through between the SB PCB and main condenser.
  • Page 17 VBA21001-R.3753.A 2. Rear body Remote block ・Remove SW-FPC [#B2006]. ・Take the two screws (#683). ・Remove the remote block (#158). #B2006 #354 #683×2 #158 DC/DC PCB ・Remove the eight wires (connected from SB-PCB, LOFT PCB, Battery contacts, and Battery box). ・Take out the two screws (#670). ・Remove the DC/DC PCB.
  • Page 18 VBA21001-R.3753.A SB PCB Main condenser unit ・Unsolder the two wires of the main condenser unit. the two wires of the main condenser unit. #142 ・Remove the main condenser that is attached on with the #1076 adhesive double-coated tape. #1077 ・Take out the screw (#687). #140 ・Remove the SB PCB.
  • Page 19 VBA21001-R.3753.A 3. Front Body Eyepiece barrel unit AE FPC unit ・Take out the screw (#607), and remove the AE FPC retainer plate (#293). ・Remove the FPC of the AE FPC unit (#B2008) from the connector. ・Take out the screw (#604), and remove the AE sensor plate spring (#285). ・Take out the screw (#291), and remove the AE FPC unit (#B2008) and AE sensor adjusting spring (#290).
  • Page 20 VBA21001-R.3753.A Penta unit Screen areas ・Take out the two screws (#635), and remove [#201] and [#202-1]. ・Remove the hollow penta prism unit (#B4) ,which is adhered by Super X. ・Remove the finder field frame 2 (#283). ・Take out the two screws (#635), and remove the SI retaining unit (#B277). ・Remove the finder field frame 1 (#282-1).
  • Page 21 VBA21001-R.3753.A Connection-FPC ・Take out the screw (#670). ・Remove the connection-FPC (#1020) from the connector. #670 Connection-FPC (#1020) AF sensor unit ・Disconnect the AF sensor unit FPC from the connector. AF sensor unit FPC ・Take out the three screws (#162) with hexagonal wrench (φ1.5mm). The AF sensor unit (#B2163) and the three springs (#161) come off.
  • Page 22 VBA21001-R.3753.A SQ FPC ・Unsolder eight wires (connected from SQ, Fmin, and Mg). ・Remove the four solder bridges. ・Remove the SQ FPC by releasing from the two bosses. SQ FPC Boss×2 Black:SQ Black:Fmin Red:Mg Solder bridge ×4 Blue:Mg Orange:Fmin Yellow:SQ Green:SQ Gray:SQ Shutter unit ・...
  • Page 23 VBA21001-R.3753.A In-finder LCD unit ・Take out the two screws (#683). ・Remove the in-finder LCD unit (#B2010). #683×2 #B2010 #276 #295 #758 SB SW unit ・Remove the three solder bridges. ・Remove the SB SW unit (#B1012). ・Remove the front body FPC from the connector. SB SW unit (#B1012) Front body FPC Solder bridge ×3...
  • Page 24 VBA21001-R.3753.A Front body FPC SI LED-FPC ・Remove the gasket (#485), and two pieces of tape. ・Remove the seven solder bridges and the other four solder bridges. # TA-00( × ) TA-00( × ) Solder bridge×4 Solder bridge×7 ・Remove the SI LED-FPC (#1011) and [#279]. ・Remove the front body FPC (#1009).
  • Page 25 VBA21001-R.3753.A Relay PCB ・Unsolder the two wires (connected from SQ PCB unit). ・Take out the screw (#607). #607 ・Remove the relay PCB. Relay PCB Red:SQ PCB unit Black:SQ PCB unit SQ PCB unit ・Take out the three screws (#638). ・Turn " ① " part in the direction of the arrow, and remove the SQ PCB unit, while releasing from the roller section.
  • Page 26 VBA21001-R.3753.A Bayonet / A/M-change SW / Lens-contact areas #621×2 #115 #119 #B116 #37-3 #137 #B2113 #198 #638×2 #189 #112×3 #135 #607 #660 #111 #648×5 - Ｄ  ･ logo_Q0650_forGraphic 071004_Gdesign_ito...
  • Page 27 VBA21001-R.3753.A Aperture lever / F-min SW areas #190 #205 #206 #207 #203 #209 #210 #1106 #208 #639 #133 #204 #136 #213 #1105 #134 #645 #B2231 Mirror unit #240 #238 #239 #199×2 #236 - Ｄ  ･ logo_Q0650_forGraphic 071004_Gdesign_ito...
  • Page 28 VBA21001-R.3753.A Assembly/ Adjustment ・ NOTE: For undescribed tapes and sponges here in"Assembly", refer to PARTS LIST. 1. Front body Mirror unit #B2231 #240 #239 #238 Be careful NOT to bend here. #199×2 #236 ・ With the mirror being raised, assemble the pins and apply the adhesive (Super X) on each pin.
  • Page 29 VBA21001-R.3753.A Aperture lever F-min SW areas　 #190 Grease: LEN317A #205 #206 Grease: LEN317A #203 #209 #207 #210 #1105 #208 #639 #133 #204 #136 #213 #1106 #134 #645 Black:SQ FPC Orange:SQ FPC Position for hooking spring ・Hook [#205] and then [#204]. ・Hook [#213].
  • Page 30 VBA21001-R.3753.A SQ PCB unit ・Move the roller section of the aperture control unit to the position as shown in Fig. ① . ・Turn " １" all the way to the end in the direction of the arrow. Then, Press " ２" in the direction of "Lock". ・Turn "...
  • Page 31 VBA21001-R.3753.A Lens contacts unit #B2113 #198 #638×2 #189 Release button unit #621×2 #115 #119 #B116 - Ａ  ･ logo_Q0650_forGraphic 071004_Gdesign_ito...
  • Page 32 VBA21001-R.3753.A Bayonet Mount GND plate #137 #112 Grease: LEN317A Grease: LEN317A #111 ・ Put [#135] and fix it with the screw (#607). ③ ⑤ ・ Attach [#137]. #135 #607 ② ・ Attach three pieces [#112]. ⑥ ・ Mount the bayonet (#111). #112×3 ・...
  • Page 33 VBA21001-R.3753.A Relay-PCB unit ・ Mount the relay-PCB unit (#1004) in the direction for positioning, and fix it with the screw (#607). ・ Arrange the wires as shown in "Fig. ① ". ・ Solder the five wires (connected from #607 SB-PCB, TOGO PCB, and SQ PCB unit). Relay-PCB Direction for positioning Red:SB PCB...
  • Page 34 VBA21001-R.3753.A ・Fold the contact-FPC down, and attach it by fitting the four bosses in the holes. ・Make seven solder bridges and four solder bridges. ・Attach the two pieces of tape and gasket. #485 TA-0025(5×8) TA-0025(5×5) Solder bridge×4 Solder bridge×7 Contact-FPC In-finder LCD unit ・Fix the in-finder LCD unit (#B2010) with the two screws (#683).
  • Page 35 VBA21001-R.3753.A Shutter unit ・Turn the white gear in the direction of "A", and raise the mirror. ・Mount the shutter unit (#31), and fix it with two screws (#635). ・Turn the white gear in the direction of "B", and let the mirror down. ・Attach [#757].
  • Page 36 VBA21001-R.3753.A AF sensor unit ・Put three springs (#161) and mount the AF sensor unit [#B2163]. ・Turn three screws (#162) with Hexagonal wrench (φ1.5mm) all the way lightly to the end, then #B2163 give each two-turns counterclock- wise. #162×3 #161×3 ・Attach the AF sensor unit FPC by following the shape of the attaching surface, and connect it to the connector. AF sensor unit FPC Connection-FPC ・Connect the connection-FPC (#1020) to the connector, and fix it with the screw (#670).
  • Page 37 VBA21001-R.3753.A Penta unit Screen areas ・Mount SI (#13). ・Mount the finder field frame 1 (#282-1) by positioning towards the direction of the arrow. ・Attach the in-finder display prism (#9). ・Mount the SI-retaining unit (#B277) and fix it with two screws (#635). ・Mount the finder field frame 2 (#283).
  • Page 38 VBA21001-R.3753.A Eyepiece barrel unit AE FPC unit ・Mount the eyepiece barrel unit (#B261), and fix it with two screws (#638). ・Put the AE sensor adjusting-spring [#290] and AE FPC unit [#B2008]. Turn the screw (#291) all the way lightly to the end, then give each two-and-half turns counterclockwise. ・Put the AE sensor plate-spring (#285), and fix it with the screw (#604).
  • Page 39 VBA21001-R.3753.A Angle inspection and adjustment of Main mirror and sub-mirror ※ Procedure: Follow the operating instructions of the tool for main/sub mirror angle-inspection (J19132). ・Main mirror 45° adjustment Caution: Before and after the adjustment, check the accuracy by moving the main mirror up- and downwards a few times.
  • Page 40 VBA21001-R.3753.A 2. Rear body Battery box #607×3 #157×3 Battery drop-proofing spring Buzzer unit Backup battery #607 Battery box Battery box Eyelet ring unit Other small parts ・Put the DC/DC lug plate (#159) at the final stage, then fix the battery box with the four screws (#615). #B145×2 #694×2 #450...
  • Page 41 VBA21001-R.3753.A SB PCB ・Fit the SB-PCB with the boss, and fix it with the screw (#687). ・Solder the two wires (connected from DC/DC-PCB) and put them in the Main condenser unit groove for arrangement. ・Adhere the main condenser unit with the adhesive double-coated tape by #142 #1076 putting in the direction for positioning.
  • Page 42 VBA21001-R.3753.A DC/DC PCB ・Mount the DC/DC-PCB, and fix it with two screws (#670). ・Put the wires in the groove for arrangement, and solder eight wires (connected from SB-PCB, LOFT PCB, Red: Battery contact (+) Battery contacts and Battery box). Blue: Battery box (ID) Black:Battery contact (-) #670×2 Blue:LOFT PCB...
  • Page 43 VBA21001-R.3753.A 3. Mounting of Front body on Rear body ・Pass the wires of the relay-PCB through behind the main condenser, and assemble the front body into the rear body. ・Tighten four screws (#624) in the order from ① ④ The wire that is connected SB-PCB from the relay-PCB must not mount on the other two wires.
  • Page 44 Inspection and Adjustment of Body back "0" positioning of the dial gauge ＊ 0" position of D60 Surface plate ① Put the tool (J18001-1) on the surface plate, and set the dial gauge to "0". ② Turn the index ring in the direction of the arrow from the above "0", and set the scale to "8 .
  • Page 45 VBA21001-R.3753.A DC/DC PCB ・Solder the two wires (connected from Mount GND plate and Front body FPC). Black: Mount GND plate Black: Front body FPC SB PCB ・Solder the two wires (connected from Relay-PCB). Red: Relay-PCB Black: Relay-PCB - Ａ  ･ logo_Q0650_forGraphic 071004_Gdesign_ito...
  • Page 46 VBA21001-R.3753.A Assembly of Top cover Shoe base ・Fix [#B317], shoe base (#316), [#318], and [#322] with four screws (#654). #318 #316 #B317 Oil barrier: OS-30MEL (OS-30MF is available) #311×2 #322 #654×4 Mode dial unit ・Fix [#460-1],[461-1],[6371-2], [#373], #460-1 and [#372] with the screw (#640). #461-1 #6371-2 Grease: LEN317A...
  • Page 47 VBA21001-R.3753.A C/D unit / Buttons / Other small parts ・Fix the C/D unit (#B367) with two screws (#635). ・Attach [#387] and AF/AE lock button (#5386). #6027 #5386 Direction for positioning #387 #B367 #326 Adhesive Super X Adhesive Super X #635×2 Top cover FPC unit ・Put the wire (#1071-1) in position as below.
  • Page 48 VBA21001-R.3753.A SB release base unit ・Mount the SB release base unit (#B2455), and fix it with two screws (#607). #B2455 #607×2 SB lower case unit / Other small parts ・By watching the wires, mount the SB lower case unit (#B2302). ・While releasing the two hooks, attach [#308].
  • Page 49 VBA21001-R.3753.A ・While pressing the SB case rotating shaft (#306), attach the SB-up spring (#305) by pushing it in the direction attach the SB-up spring (#305) by pushing it in the direction of the arrow, then fix it with the screw (#733). #305 #733 #306...
  • Page 50 VBA21001-R.3753.A AF-assist illuminator unit ・Mount the AF-assist illuminator unit (#B325), and fix it with the screw (#608). ・Solder the two wires (connected from AF-assist illuminator unit). #0 AF-assist illuminator unit (#B325) Black : AF-assist illuminator unit Uncoated wire: AF-assist illuminator unit Top cover FPC / Wiring ・Make five solder bridges.
  • Page 51 VBA21001-R.3753.A SB upper case ・Mount the SB upper case (#5301) on the SB lower case unit. SB upper case #5301 Claw SB lower case unit ・Press the pop-up lever A part of the top cover unit, and raise the built-in SB. Pop-up lever A part ・Tighten two screws (#632).
  • Page 52 VBA21001-R.3753.A When the AE-CCD positioning is adjusted, solder the only four wires that connected from the top cover to SB-PCB. Then, make a temporary assembly without mounting the rubber eye- cap (#B271), and assemble up to Page A27. Top cover ・Mount the rubber eyecap (#B271).
  • Page 53 VBA21001-R.3753.A CCD unit ・Mount the CCD unit (#B3051) by following the direction for positioning, and fix it with three screws (#631). Caution: #631×3 Some bodies have already washer(s) attached on the mounting surface of CCD unit. Direction for positioning #B3051 Loft PCB / TOGO PCB ・Attach the loft PCB partially with the adhesive double-coated tape.
  • Page 54 VBA21001-R.3753.A ・Connect the harness to the connector. ・Tighten five screws (#663). ・Solder six wires (two connected from Relay-PCB/Backup battery, two coated and two uncoated). ・Connect the six FPCs to each connector Pink:Relay-PCB #663×5 Harness TOGO-PCB (#B2001) Coated Coated #483 Uncoated Uncoated TA-0025(5×8) Blue: Backup battery...
  • Page 55 Set the camera AF to manual, and the focus ring to "0.7 m" by rotating it. ⑦　 　 Start up the inspection and adjustment software for D60 (J18443), and select "Inspection and Adjustment for AE CCD POSITION" then "Set Camera for AE CCD POSITION".
  • Page 56 VBA21001-R.3753.A (#B2008) Metering FPC unit Metering FPC unit Metering FPC unit Standard →　Reference screw X-direction　→　a: Screw #291-1 Y-direction　→　b: Screw Y-direction (b) #741 tightening Ｘ -direction (a) Ｘ -direction (a) tightening loosening Adhesive: Screwlock Y-direction (b) loosening Discharge of Main condenser ・...
  • Page 57 VBA21001-R.3753.A Covers ・Assemble the front cover unit (#B24) together with the Fmin coupling block (#131). #5610×2 Adhesive: Super X #B24 Adhesive: Super X #6074 #670 #5120 #626 #5610×2 #792C #750×2 #131 Adhesive: Aronalpha (Quick drying glue) Gap adjustment of SB lighting unit ・In case the result is out of standard, raise the SB unit and make an adjustment by turning the adjusting dial with Hexagonal wrench.
  • Page 58 VBA21001-R.3753.A △ (Addition) Rear cover Adhesive:Alon Alfa #402 #403 Put [#426-1] in [#6401], and join them with the adhesive. #5424 Direction for positioning #6401-3 #5425 #5426 #5427 #421 #425-2×2 #426-1 #405×2 #404×2 #5429 #448 #423 #408 Direction for positioning #753 #1016 #5418 #1037...
  • Page 59 VBA21001-R.3753.A Rear cover (continued) ・Connect the TFT-PCB connection-FPC to the connector. ・Mount the rear cover. #5618×2 ・Tighten four screws (#6690) and two screws (#5618). #6690×4 Rear cover Rear FPC - Ａ  ･ logo_Q0650_forGraphic 071004_Gdesign_ito...
  • Page 60 To USB terminal Power connector (EP-5) ＋ AC adapter (EH-5) Power connector (EP-5) ＋ EP-5 D60 adjustment software　J Caution: When performing “Adjustment for BATTERY ★ CHECK LEVEL”, process the power connector (EP-5) and use it. Shutter tester (EF-1) (J19123) Flash meter...
  • Page 61 VBA21001-R.3753.A D60 Inspection and Adjustment Software (J18443) This inspection and adjustment software runs on Windows. Install the software by following the below procedure. <Operating environment> Check the following operating environment which is required for installing this program on PC. IBM PC/AT compatible...
  • Page 62 VBA21001-R.3753.A 2. Paste the file (PD60.EXE) in the created folder. 3. Double-click on the pasted file to display the following screen. Press the OK button, then decompression starts. - Ａ  ･ logo_Q0650_forGraphic 071004_Gdesign_ito...
  • Page 63 VBA21001-R.3753.A 4. When the decompression of file is finished, the file (D60.exe) is created. 5. The install is completed. △ (Addition) < Procedure for installing USB driver > [When Windows 2000 is used] If this program is used by the USB interface, installing the USB driver is necessary.
  • Page 64 VBA21001-R.3753.A <Start-up of Program> 1. Double-click the file (D60.exe), then Inspection and adjustment program for D60 starts. 2. To display in Japanese, select the radio button "JAPANESE" in "LANGUAGE" in the lower right-hand corner of the screen. 　However, this is not properly viewed in the English OS.
  • Page 65 SB. (ref. adjustment software for details) AF inspection and adjustment Note: When the adjustment software is used for the first time, prepare three D60 cameras and measure by "WRITING of AF ADJ. LENS OFFSET VALUE" on the main menu. If "LDATA.DAT"of D40(D40X) is obtained under the same environment, copy it into a folder of D60 adjustment software, and change "D40(D40X)"...
  • Page 66 VBA21001-R.3753.A Eye sensor inspection and adjustment Caution: When this adjustment software is used for the first time, prepare three units of D60, and get the reference values of the eye sensor for the main menu. △ (Addition) Reference line (Eye-sensor) face Standard reflector (10cm×10cm)
  • Page 67 VBA21001-R.3753.A Bottom cover ･ Mount the bottom cover. ・ Fix it with four screws (#5735) and five screws (#5674). #5674×2 #5674 #5674 #5735 Power cord lid Direction for positioning Bottom cover #5674 #5735 #5735×2 ∞ Infinity focus inspection & adjustment ・...
  • Page 68 VBA21001-R.3753.A Necessary adjustments when parts are replaced 1. D60 adjustment items and Firmware updates Writing of Aperture Battery Built-in SB Eye sensor 　　　　Adjustments AE CCD EEPROM accuracy accuracy check volt- light volume accuracy inspection positioning fixed inspection & inspection age level inspection &...
  • Page 69 VBA21001-R.3753.A 2. Shooting image adjustment items and Firmware updates Pixel Fac- ＊  Gr/Gb Gr/Gb Pixel Image defect 　　　Adjustments tory Ver. difference com- defect Writing shut- Sensi- com- Serial Sensi- compen- pensa- compen- of fixed Shading adjust tivity pensa- no.input tivity fault Ser.
  • Page 70 When D60 shooting image-related and listed parts on Page A42 are replaced, be sure to make an adjustment by the shooting image adjustment software for D60 (J65108). The details of its function and how to use this software are as follows: 2.
  • Page 71 VBA21001-R.3753.A 4. Basic usage 　1. Execute "D60IMG.exe" to start up the main screen. (ref. Fig.1) 　2. Select ENGLISH / JAPANESE in Language to display any menu. (ref. Fig.2) 　3. Click the button to start adjustments. ※ When the adjustments from (1) to (7) are made, calculate to get the reference values of sensitivity and sensitivity ratio by using the reference body beforehand, then perform the adjustments.
  • Page 72 VBA21001-R.3753.A 5. Required equipment and conditions AC adapter EH-5 and USB cable (mini B type) UC-E4 are used for all adjustments so they are not specified ※ in the list. ※ 5100K color viewer: Ex-model viewer【J63049】is also available. ※ For color viewer and shutter tester, use luminance meter MB-3000【J63068】for measurements.　　 Required device/condition ND filter Color filter...
  • Page 73 VBA21001-R.3753.A 6. Summary 　The summary on each adjustment is as follows: 　(1) Gr/Gb difference compensation adjustment (G filter) Camera is faced to the light-emitting box (color viewer) of LV13 equiv. with SP2 (G filter) being put between them. G-line crawl (3890×2606 pixels) is divided into (29×25) blocks, and the adjustment is made so that the difference between Gr and Gb output can fall in the standard range.
  • Page 74 VBA21001-R.3753.A 　(7) Pixel defect compensation - black point When pixels of which the output level is under specified value with LV13 equiv., are detected, the coordinates of the detected pixels are rewritten as pixel defect compensation data. 　(8) Pixel defect compensation - white point Shots are taken on the dark surface.
  • Page 75 VBA21001-R.3753.A 7. Procedure 7-1. Shooting image adjustment Caution: For D40X, use D80 as reference body. 　● Calculate the "Sensitivity" and "Sensitivity ratio" reference values by using D80 reference body beforehand, △ (Revision) 7-4 then perform the adjustments. (ref. 9-4.) 　● For shooting image adjustment, make all items from (1) to (8). The adjustments from (1) through (8) are all programmed to be executed in serial order.
  • Page 76 VBA21001-R.3753.A 　(3) Shading adjustment 　・Click "Start". 　・Setting conditions are displayed. ・Attach the tool lens (Aperture F5.6) and ND filter (ND 8× 1) to the camera. 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・Click "OK".
  • Page 77 VBA21001-R.3753.A (5) Sensitivity ratio adjustment 　・Click "Start". 　・Setting conditions are displayed. 　・Attach the tool lens (Aperture F5.6) (without filter). 　・Get the camera closest to the center of the illuminated surface of the shutter tester (LV9). 　・Click "OK". 　・The adjustment starts. When it is completed, the next setting conditions are displayed. ・Attach the tool lens (Aperture F5.6) and ND filter (ND8×1).
  • Page 78 VBA21001-R.3753.A 7-3. Pixel defect compensation - white point 　・Click "Start". 　・Setting conditions are displayed. 　・Cap the camera with the body cap or lens cap to shield light from the mount. 　・Click "OK". 　・The adjustment starts. When it is completed, "OK" is displayed. 　・Click "OK".
  • Page 79 VBA21001-R.3753.A 7-5. Reading of RISC version 　・Click "RISC VERSION" of the menu on screen. 　・RISC version is displayed. 7-6. TFT adjustment 　・Click "TFT ADJUSTMENT" on the menu. 　Writing of TFT fixed values 　・Click "REWRITING THE TFT FIXED VALUE". 　・The message "Will you rewrite the CAMERA?" appears. 　・Click "Yes".
  • Page 80 VBA21001-R.3753.A ＜ Measurement of Consumption current value ＞ When this camera is used for measuring the consumption current value, connect the power connector (EP-5) and install wiring as follows for the measurement. 7.8V 0.3Ω － ＋ ＋ － Ａ ※ EP-5 ※...
  • Page 81 VBA21001-R.3753.A Ｄ６０実体配線図 Ｄ６０ＷＩＲＩＮＧ SI-FPC RELEASE SW-FPC TOP COVER FPC 上カバー FPC レリーズ SW-FPC BLACK TO SHUTTER UNIT シャッターユニットへ UNCOATED BLUE BLACK APERTURE PI-FPC LENS CONTACT FPC 露出補正 SW 絞り PI-FPC レンズ接点 FPC 電源 SW EXPOSURE COMPENSATION SW POWER SW 検査端子 SQ-FPC INSPECTION TERMINAL APERTURE MG...
  • Page 82 VBA21001-R.3753.A Inspection standards Items Judgment standard Remarks External view Step Between top cover and apron: 0.2 mm or less Visual check (height difference) Other parts: 0.3 mm or less; Inside elements must not be seen. Digital micrometer Moving parts: 0.5 mm or less Clearance from Top cover to Apron;...
  • Page 83 VBA21001-R.3753.A Items Judgment standard Remarks AF accuracy Center:0 ± 4 mrad Others: 0 ± 2 mrad Special tool Brightness box Pitch Center: 0 ± 5 mrad Others: 0 ± 0 mrad Difference btwn vertically and horizontally (center): 45μm or Def amount less AF-assist illuminator Lighting level...
  • Page 84 VBA21001-R.3753.A Items Judgment standard Remarks Viewfinder In-finder LCD Tilt from finder screen: 1°or less Visual check position Tilt: (Right-left tilt from the lower part of finder field frame): Shoot the finder 90’ or less field frame with Finder field frame ±...
  • Page 85 VBA21001-R.3753.A Items Judgment standard Remarks Standby / consumed Main SW / OFF: 200μA or less (when inner battery is fully Power source: 7.8V current Luminance: EV2 charged) Lens: Main SW / ON (Half-release timer: OFF): 200μA or less (when 8-55/3.5-5.6G inner battery is fully charged) Oscilloscope: Main SW / ON (Half-release timer: ON): 200mA or less (when...
  • Page 86 VBA21001-R.3753.A Item Judgment standard Remark Image-related Judgment method AF50mm/F.4D F5.6,/30 Appropriate level When recorded in RAW format: ISO00 LV0 Within the area of 425×425 pixels at the center of screen, calculate the ISO200 LV9 average of G-2 bit data. ISO400 LV8 When recorded in JPEG format: ISO800 LV7 Within the area of 425×425 pixels at the center of screen, calculate the...
  • Page 87 VBA21001-R.3753.A Item Judgment standard Remark Dust in shot image Judgment method AF05mm/F2.8D Compensate exposure so that the center of "425×425 pixel" image becomes + EV (80 ±30 LSB), compared to correct exposure. AE: M mode Judge based on dust contrast, size, quantity, and distance btwn dusts, of Shoot object with 500K 500K the whole screen.
  • Page 88 Infinity focus adjustment screen J18362 反射ミラー FOR D70,D70s,D50,D40.D40X Reflection mirror J18443 Ｄ６０調整用ソフト ★ Adj.SOFT for D60 J65108 Ｄ６０撮像調整ソフト ★ D60 IMAGE SENSOR ADJ.SOFT J18230 ＹＡＷ、ＰＩＴＣＨ工具 FOR F5,F100,F90,F90X,D-SLR Yaw,Pitch adjustment tool J15259 ＡＦ調整工具台 AF adjusting tool J15280 Ｚレンズ用支持ホルダー Lens holder J15264 高周波タイプ蛍光灯器具...
  • Page 89 VBA21001-R.3753.A ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others J19132 メイン・サブミラー角度検査機 J19110 Back focus collimator MAIN/SUB MIRROR ANGLE INSPECTION TOOL J61218 Sub mirrorinspectiontool J18037-2 Optical parallel is available J18004 絞りレバー高さ点検工具 Aperture lever positioning gauge J19004-1 インジケータ及びスタンド （ボディバック台、ゲージ） Dial indicator and Stand J18001-1 ボディバック出し工具...
  • Page 90 VBA21001-R.3753.A ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others J18191 ＮＤフィルタ－８Ｘ FOR D100,D2H,D70,D70s,D50 ND filter 8X D200,D80,D40,D40X J18358 ＮＤフィルタ－４Ｘ 1 枚使用 ND filter 4X It uses by one pieces J63085 ﾌｨﾙﾀｰ SP1 (75X75MM) FOR D2H,D70,D70s,D50,D200 Filter SP1 (75X75MM) D80,D40,D40X J63086 ﾌｨﾙﾀｰ...
  • Page 91 VBA21001-R.3753.A ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others 汎用品 アロンアルファ RJ is Not available Quick drying glue 汎用品 フラッシュメーター RJ is Not available Flash Meter デジタルマルチメータ 汎用品 Digital　meter RJ is Not available ＡＣアダプター　ＥＨ－５ 製品転用 AC adapter EH-5 RJ is Not available 製品転用...

Table of Contents