Mts Broadcast; Vhs Hi-Fi Stereo System - Panasonic Omnivision PV-V4523S Operating Instructions Manual

MTS Broadcast

Connection
Make the Audio/Video Connection as shown on page 3.
• You can use a TV connected to Stereo amp and speakers instead of a Stereo TV.
TV
VCR
R
L
VHF/UHF
Receivable Broadcast Types
The following are possible audio broadcast types and on-screen displays.
The signal being received is indicated with an " " mark while the selected audio mode is
indicated with an arrow.
To display the broadcast signal being received,
➛ ➛ ➛ ➛ ➛ press DISPLAY*.
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main language)
and Secondary Audio Program (sub language)
broadcasts are being received simultaneously.
Select STEREO or SAP audio mode.
MTS Stereo broadcast
Multi-channel Television Sound Stereo broadcast.
Select STEREO audio mode.
• If stereo broadcast is weak and display flickers,
select MONO audio mode for possible better results.
SAP broadcast
Secondary Audio Program (sub language) broadcast.
Select SAP audio mode for the sub language.
MONO broadcast
Normal monaural sound broadcast.
Equipped with ® -TV Noise Reduction for true
®
MTS reproduction. -TV Noise Reduction is
required for good stereo separation and audio
fidelity. ® is a registered trademark, and is
licensed by ® Technology Licensing.
Stereo Amplifier
AUDIO OUT
R
R
L
AUDIO IN
R
L
OUT TO TV
STOP 1 2 : 0 0AM CH 02
0 : 0 0 : 0 0
STEREO
SAP
MONO
STOP 1 2 : 0 0AM CH 02
0 : 0 0 : 0 0
STEREO
SAP
MONO
STOP 1 2 : 0 0AM CH 02
0 : 0 0 : 0 0
STEREO
SAP
MONO
STOP 1 2 : 0 0AM CH 02
0 : 0 0 : 0 0
STEREO
SAP
MONO
- 4 -

VHS Hi-Fi Stereo System

Audio Mode for Recording
1
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
2
STEREO
SAP
MONO
• Arrow indicates selection.
3
Make a recording.
See p. 5 of "Basic Operations" Instruction book.
Audio Mode for Playback
1
Start playback.
See p. 5 of "Basic Operations" Instruction book.
2
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
3
H I F I : L / R
H I F I : L
H I F I : R
NORMAL
SP
• Arrow indicates
selection.
SP
Notes
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound.
Standard stereo tapes will playback in monaural sound.
• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to
a stereo TV or an external stereo amp and speakers. (See page 4.)
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
SP • Hi-Fi and normal audio playback volume level may differ.
SP
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
Press SAP/ Hi-Fi repeatedly
to select desired mode.
• Refer to "Receivable
Broadcast Types" on page 4.
Press SAP/ Hi-Fi repeatedly
to select desired mode.
• Select "HIFI(L/R)" or
"HIFI(L)" or "HIFI(R)" to
listen to stereo recordings in
stereo sound.
Select "NORMAL" for
monaural sound.
- 5 -