SVR-632U HDD Installation ............6 SVR-632S HDD Installation ............10 Connect to the NVR ..............11 Use SEEnergy Device Search Utility ..........11 Access the NVR with its default IP address ........14 Set up Password ................16 Camera Installation ..............17 Add a Camera -- Automatic Search ..........
SVR-632U & 632S Quick Guide LED Definition Buttons Power Reset/Restore default • Press and release for restart • Press and hold for 3 seconds then release for restore to default, when 3 seconds is reached, system LED blinks until release of button LEDs Restore default •System LED blinks until release of button...
SVR-632U & 632S Quick Guide Installation SVR-632U HDD Installation Start by removing the front plate. To remove the front plate, turn the tool-less screws on both sides counter-clock wise to loose it from the unit. Please note the screws will still be attached to the front plate even after the screws are completely loosen from the unit.
Page 7
SVR-632U & 632S Quick Guide Simply pull to remove the front plate once the screws are loosened from the unit. Remove the HDD tray by pulling the latch.
Page 8
SVR-632U & 632S Quick Guide Push the tray door back to the case to secure it. Once the tray is removed from the unit, notice there are four holes, which are used to secure the HDD.
Page 9
SVR-632U & 632S Quick Guide Once the HDD is placed in the tray, flip it over and secure the HDD with the screws. Push the tray back in to the unit and push it all the way in.
SVR-632U & 632S Quick Guide Secure the tray by pushing in the latch, which locks the tray with the unit. SVR-632S HDD Installation The installation step of SVR-632S is same as SVR-632U.
The NVR is placed in a network without DHCP server (or you are connecting to it directly): Access the NVR with its default IP * Please install Ethernet cable on Ethernet 1 port of SVR-632S. Use SEEnergy Device Search Utility If the NVR is placed in a corporate network or a local area network where a DHCP server is already presented, run the “SEEnergy Device...
Page 12
SVR-632U & 632S Quick Guide To begin, launch the “SEEnergy Device Search” utility from the CD and proceed with the installation:...
Page 13
SVR-632U & 632S Quick Guide Once the installation is complete, check the “Launch the Search AP” option and click “Finish”. The search should start automatically and its status should be dis- played. The NVR should be located and its IP address should be displayed. Double-click on an NVR and the search program should automatically access the NVR’s web administration page from your default browser.
SVR-632U & 632S Quick Guide You should be prompted for the NVR’s username and password. Enter its default username “admin” and password “admin” and then click”OK” to enter the system Access the NVR with its default IP address The NVR comes with a pre-configured static IP “192.168.101.50”. However, it is only used when there is no DHCP server presented in the network.
Page 15
SVR-632U & 632S Quick Guide The PC that is connected directly to the NVR (or within the same local area network) should receive an IP from the NVR. Simply access the NVR from your web browser with its IP address Again, you should be prompted for the username and password.
SVR-632U & 632S Quick Guide Set up Password The default login username and password is admin/admin. To change the password of the admin account, go to “Setup” --> “System Con- figurations” --> “User Account”, click on the “admin” account in the account list then press the “edit”...
SVR-632U & 632S Quick Guide Camera Installation Add a Camera -- Automatic Search Click the “Search” button to perform the camera search. You should be prompted to install Active Control component in order for the search to function properly. Go ahead and click “Install” After that, the search should begin and its status should be displayed:...
Page 18
SVR-632U & 632S Quick Guide Found cameras should be listed and simply select a camera from the list and press “Configure” Its corresponding information should be displayed in the “Camera Information” section. Enter its username and password and select the channel ID and name the camera.
SVR-632U & 632S Quick Guide Click on “Detect” to establish connection between the recorder and the camera. If connection establishes successfully, camera’s detailed information should be polled and displayed as below. Adjust its video format, frame rate, resolution or bitrate...etc if you wish and then click “Add”...