LED Definition ................5 Installation ................6 HDD Installation ................6 Connect to the NVR ............... 14 Use SEEnergy Device Search Utility ..........14 Access the NVR with its default IP address ........17 Set up Password ................19 Camera Installation ..............20 Add a Camera -- Automatic Search ..........
6
[SVR-‐204
Q UICK
G UIDE]
Installation HDD Installation Locate the screws highlighted above on the back of the NVR. Use a Philips screw driver to release the screws.
Page 7
[SVR-‐204
Q UICK
G UIDE]
Slide open the case as shown above. One side of the housing can be detached as shown above.
Page 8
8
[SVR-‐204
Q UICK
G UIDE]
Install the bottom HDD by slide it in to the tray diagonally to avoid the tray seperator. Once the HDD is placed into the tray, you should see a gap between the HDD and the SATA connector.
Page 9
[SVR-‐204
Q UICK
G UIDE]
Attach the HDD to the SATA connector by sliding it towards the connector. Make sure the screw holes on the HDD are aligned with the ones on the tray.
Page 10
10
[SVR-‐204
Q UICK
G UIDE]
Secure the HDD with the screws provided in the accessory box with a Philips screw driver. There are four for each HDD; two for each side of the tray. 4-Ch Network Video Recorder with HDMI Install the top HDD by attaching it to the corresponding SATA cable first.
Page 11
[SVR-‐204
Q UICK
G UIDE]
Make sure the HDD is securely attached. Place the HDD to the tray and make sure the screw holes on the HDD are aligned with the ones on the tray.
Page 12
12
[SVR-‐204
Q UICK
G UIDE]
Secure the HDD with the screws provided in the accessory box with a Philips screw driver. There are four for each HDD; two for each side of the tray. Slide the side housing back to the unit.
Page 13
[SVR-‐204
Q UICK
G UIDE]
Secure the housing with the screws highlighted above.
Use SEEnergy Device Search Utility If the NVR is placed in a corporate network or a local area network where a DHCP server is already presented, run the “SEEnergy Device Search” utility from a computer that is on the same network and locate the NVR with its IP address that is assigned by the top-level DHCP server.
Page 15
[SVR-‐204
Q UICK
G UIDE]
To begin, launch the “SEEnergy Deivce Search” utility from the CD and proceed with the installation:...
Page 16
16
[SVR-‐204
Q UICK
G UIDE]
Once the installation is complete, check the “Launch the Search AP” option and click “Finish”. The search should start automatically and its status should be dis- played. The NVR should be located and its IP address should be displayed. Double-click on an NVR and the search program should automati- cally access the NVR’s web administration page from your default browser.
[SVR-‐204
Q UICK
G UIDE]
You should be prompted for the the NVR’s username and password. Enter its default username “admin” and password “admin” and then click”OK” to enter the system Access the NVR with its default IP address The NVR comes with a pre-configured static IP “192.168.101.50”.
Page 18
18
[SVR-‐204
Q UICK
G UIDE]
The PC that is connected directly to the NVR (or within the same local area network) should receive an IP from the NVR. Simply access the NVR from your web browser with its IP address Again, you should be prompted for the username and password.
[SVR-‐204
Q UICK
G UIDE]
Set up Password The default login username and password is admin/admin. To change the password of the admin account, go to “Setup” --> “System Con- figurations” --> “User Account”, click on the “admin” account in the account list then press the “edit”...
20
[SVR-‐204
Q UICK
G UIDE]
Camera Installation Add a Camera -- Automatic Search Click the “Search” button to perform the camera search. You should be prompted to install Active Control component in order for the search to function properly. Go ahead and click “Install” After that, the search should begin and its status should be displayed:...
Page 21
[SVR-‐204
Q UICK
G UIDE]
Found cameras should be listed and simply select a camera from the list and press “Configure” Its corresponding information should be displayed in the “Camera Information” section. Enter its username and password and select the channel ID and name the camera.
22
[SVR-‐204
Q UICK
G UIDE]
Click on “Detect” to establish connection between the recorder and the camera. If connection establishes successfully, camera’s detailed information should be polled and displayed as below. Adjust its video format, frame rate, resolution or bitrate...etc if you wish and then click “Add”...