Network Configuration - Samsung XRN-1610S User Manual

netWORK COnFIguRAtIOn

It provides networked monitoring of Live screen from a remote place, and supports mail forwarding function with
events. You can configure the network environment which enables such functions.
Interface
You can set the network connection route and protocol.
Setting a network connection
Sets the protocol and environment of the network.
• Network 1 (Camera) : Port recommended for camera connection, which receives a image from the camera.
• Network 2 (All) : Port recommended for connection with a network, web viewer or iSCSI.
• Network 1 (Camera) / Network 2 (All) setup
- IP Type : Select a network connection type.
- IP Address, Subnet Mask, Gateway, DNS
<Static> : You can manually enter IP address, subnet mask, gateway and DNS.
<DhCp> : IP address, subnet mask and gateway values will be automatically set.
<pppoe> : IP address, subnet mask and gateway values will be automatically set.
- User ID, Password : If you set the connection mode to PPPoE, you need to enter "user ID" and
"password" to register in PPPoE.
In PnP mode, XRN-1610S Network 1 only set to DHCP.
`
We recommend not to set the same network address for Network 1 and Network 2.
`
• Transfer bandwidth : Enter the maximum amount of upload data bandwidth.
Check the assigned setting in Connection Mode before entering your value.
If the sum of the network TX/RX is less than 256Mbps, there is a max transmission rate of 256Mbps.
`
• Default Gateway : Set the basic gateway by using Network1 / Network2 setup.
You can manually input DNS of <DHCP> and <PPPoE> when it selected to <Manual>.
`
M
Connecting and Setting the network
Networking may differ from the connection method, check your environment before setting the connection
mode.
When no router is used
• Static mode
- Internet connection : Static IP, leased line, and LAN environments allows connection between the NVR and
remote user.
- NVR Network Settings : Set the <network> in <Interface> menu of the connected NVR to <Static>.
Consult your network manager for IP, Gateway and Subnet Mask.
`
• DhCp mode
- Internet connection : Connect the NVR directly to a cable modem, DHCP ADSL modem or FTTH network.
- NVR Network Settings : Set the <network> in <Interface> menu of the connected NVR to <DhCp>.
• pppoe
- Internet connection : An PPPoE modem is directly connected to the NVR, where the PPPoE connection
requires user ID and password.
- NVR Network Settings : Set the <network> in <Interface> menu of the connected NVR to <pppoe>.
PPPoE <User ID> and <Password> should be the same to the PPPoE user information.
`
If you don't know the ID and password, consult your PPPoE service provider.
When a router is used
To avoid IP address conflict with the NVR's static IP, check followings :
`
J
• Setting the nVR with a static Ip
- Internet connection : You can connect the NVR to a router which is connected to an PPPoE/Cable modem
or a router in a Local Area Network (LAN) environment.
• Setting the nVR network
1. Set the <network> in <Interface> menu of the connected NVR to <Static>.
2. Check whether the set IP address is in the static IP range provided by the Broadband Router.
IP Address, Gateway, and Subnet Mask : Consult your network manager.
Check whether the set IP address is in the static IP range provided by the Broadband Router.
`
If a DHCP server is configured with starting address (192.168.0.100) and end address (192.168.0.200), you should set the
`
J
IP address out of the configured DHCP range (192.168.0.2 ~ 192.168.0.99 and 192.168.0.201 ~ 192.168.0.254).
3. Check the Gateway address and subnet mask are equal to those set in the Broadband Router.
English _45