1. Manuals
  2. Brands
  3. STEINWAY LYNGDORF Manuals
  4. Speakers
  5. S-SERIES
  6. Installation manual

STEINWAY LYNGDORF S-SERIES Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S - SERIES
IN-WALL SERIES

INSTALLATION MANUAL

VERSION 2.2
[Skriv tekst]

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S-SERIES and is the answer not in the manual?

Questions and answers

Related Manuals for STEINWAY LYNGDORF S-SERIES

Summary of Contents for STEINWAY LYNGDORF S-SERIES

  • Page 1: Installation Manual

    S - SERIES IN-WALL SERIES INSTALLATION MANUAL VERSION 2.2 [Skriv tekst]...
  • Page 2 S-15 AND S210 ....................4   IN-WALL SERIES, S-15IW AND S-16IW ............13   S-15IW AND S-16IW WITH GRILLS ..............38   IN-CEILING S-16IW ..................64  ...
  • Page 3 Steinway Lyngdorf products and accessories comply with parts 15 and 68 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference; and (2) this device must accept any interference received, including any interference that may cause undesired operation.

  • Page 4: S-15 And S210

    INSTALLATION MANUAL S-15 AND S210...

  • Page 5: Table Of Contents

    UNPACKING ..........................6  INVENTORY ..........................6  POSITIONING OF PRODUCTS ....................7  MOUNTING BOUNDARY WOOFER FEET ................... 9  BOUNDARY WOOFER FRONT CLOTH ..................9  S-15 WALL BRACKET ......................... 10 S-15 ON-CEILING BRACKET....................101  S-15 TABLE STAND (OPTIONAL ACCESSORY)............... 12 ...

  • Page 6: Unpacking

    Contact both the shipper and your Steinway Lyngdorf representative immediately if products bear any sign of damage. All Steinway Lyngdorf equipment is carefully inspected before leaving our factory. Note: Keep the shipping carton and all packing material for future use or in the unlikely event that products require servicing.

  • Page 7: Positioning Of Products

    POSITIONING OF PRODUCTS S-15 Loudspeaker The recommended height from floor to center of the tweeter in the S-15 is:  1m / 3ft. for use as front speakers / stereo speakers  1.8m / 6ft. for use as surround speakers If possible, the wall should be constructed with the positioning of speakers in mind.
  • Page 8 S-210 Boundary Woofer We recommend placing the boundary woofers in a corner position (fig 1). Always place the boundary woofer as close to the wall as possible without touching it. If a corner placement isn’t possible, the boundary woofers must be placed up against a minimum of 1 wall as shown in fig 2.

  • Page 9: Mounting Boundary Woofer Feet

    MOUNTING BOUNDARY WOOFER FEET After locating the optimal positions for the boundary woofers, mount the supplied feet to achieve optimal stability. The boundary woofers are not intended to be used without the feet*. To mount the feet on the boundary woofers, gently lay the woofer on its back on a soft surface to prevent any damage or scratches.

  • Page 10: S-15 Wall Bracket

    S-15 WALL BRACKET When mounting the wall bracket, make sure the wall and screws can handle the total weight of the bracket and speaker. Remember to pull speaker wires from the location of the amplifiers to the bottom of the wall bracket. Place the wall bracket against the wall.

  • Page 11: S-15 On-Ceiling Bracket

    S-15 ON-CEILING BRACKET When mounting the on-ceiling bracket, make sure the ceiling and screws can handle the total weight of the bracket and speaker. Remember to pull speaker wires from the amplifiers to the back of the bracket. 1. Use the four screws to fasten the speaker plate onto the on-ceiling bracket, then mount the in- ceiling bracket to the ceiling.

  • Page 12: S-15 Table Stand (Optional Accessory)

    S-15 TABLE STAND (OPTIONAL ACCESSORY) To mount the S-15 table stand: 1. Unscrew the small cover using the included Torx Allen key. 2. Pull the speaker wire through the hole in the table stand. 3. Attach the speaker wire to the speaker terminals. 4.

  • Page 13: In-Wall Series, S-15Iw And S-16Iw

    INSTALLATION MANUAL IN-WALL SERIES, S-15IW AND S-16IW...
  • Page 14 UNPACKING ..........................15 INVENTORY ..........................15 POSITIONING OF PRODUCTS ....................16 USING THE CUTOUT TEMPLATE FOR RETROFIT APPLICATIONS ........24 SPEAKER INSTALLATION ......................25...

  • Page 15: Unpacking

    Contact both the shipper and your Steinway Lyngdorf representative immediately if products bear any sign of damage or if there is a discrepancy in the number of packages received. All Steinway Lyngdorf equipment is carefully inspected before leaving our factory. Note: Keep the shipping carton and all packing material for future use or in the unlikely event that products require servicing.

  • Page 16: Positioning Of Products

    POSITIONING OF PRODUCTS  The center of the front speaker tweeter should be in level with the primary listening position, which is approximately 1m / 3ft depending on the height of the seat.  Surround and rear speakers tweeter center should be 180cm / 6ft from the floor. Model IW-26H The IW-26H speaker weighs 12.2kg / 26.9lbs.
  • Page 17 Installation Bracket The distance between the top and bottom installation bracket must be 324mm / 12.75in. The width of the installations bracket is 60cm / 26.6in.
  • Page 18 Model IW-26V The IW-26V speaker weighs 11.3kg / 24.9lbs. Screws and wall framing must be able to support this weight. This speaker has screw terminals; please use a Phillips head screwdriver. Recommended minimum up to 16m / 50ft: AWG 14/2 or 2-lead 2mm Recommended minimum from 16m / 50ft and up: AWG 12/2 or 2-lead 3.5mm Recommended maximum: Double AWG 10/2 or 2-lead 5mm Cutout Template...
  • Page 19 Installation Bracket The distance between the top and bottom installation bracket must be 584mm / 23in. The width of the installations bracket is 35.5cm / 14in.
  • Page 20 S-15IW The S-15IW speaker weighs 3.5 kg / 7.7 lbs. Screws and wall framing must be able to support this weight. This speaker has screw terminals, please use a Phillips head screwdriver. Recommended minimum up to 16m / 50ft: AWG 14/2 or 2-lead 2mm Recommended minimum from 16m / 50ft and up: AWG 12/2 or 2-lead 3.5mm Recommended maximum: Double AWG 10/2 or 2-lead 5mm Cutout Template...
  • Page 21 Installation Bracket The distance between the top and bottom installation bracket must be 280mm / 11in. The width of the installations bracket is 35.5cm / 14in.
  • Page 22 S-16IW The S-16IW speaker weighs 5.7 kg / 12.6 lbs. Screws and wall framing must be able to support this weight. This speaker has screw terminals, please use a Phillips head screwdriver. Recommended minimum up to 16m / 50ft: AWG 14/2 or 2-lead 2mm Recommended minimum from 16m / 50ft and up: AWG 12/2 or 2-lead 3.5mm Recommended maximum: Double AWG 10/2 or 2-lead 5mm Cutout Template...
  • Page 23 Installation Bracket The distance between the top and bottom installation bracket must be 300mm / 11.8in. The width of the installations bracket is 35.5cm / 14in.

  • Page 24: Using The Cutout Template For Retrofit Applications

    USING THE CUTOUT TEMPLATE FOR RETROFIT APPLICATIONS Unpack the supplied cardboard template and place it against the wall, where the speaker will be installed. Be sure there is ample clearance between the wall studs to allow for the width of the speaker to be properly installed into the cutout.

  • Page 25: Speaker Installation

    SPEAKER INSTALLATION All-in-one 5/8in and 13mm Wall Mounting Bracket The mounting bracket is constructed to accommodate four different wall thicknesses:  5/8”  2 x 5/8”  13mm  2 x 13mm To install the bracket correctly in a 5/8” or 2x5/8” wall, you must be able to read the 5/8” text of the bottom bracket.
  • Page 26 Alignment of Speaker The cutout is designed to be larger than the speaker, and the speaker must be placed in the exact center of the cutout. Screw the mounting distance block and two angled brackets onto an installation brackets.
  • Page 27 Insert the bottom bracket into the hole and make sure the mounting distance guide is resting on the edge of the cutout flush with the surface of the wall. Pull the bracket forward until it sits firmly against the wall.
  • Page 28 Screw the bracket securely into the left and right studs. The bracket is intentionally cut slightly shorter than the distance between the studs and the angled brackets will flex when screwed into the studs.
  • Page 29 Remove the mounting distance guide.
  • Page 30 Repeat the above steps to install the top bracket. Make sure the bracket is facing the correct way. If you can read 13mm or 5/8” on the bottom bracket, turn the top bracket upside down so the same text points downwards.
  • Page 31 Connect the speaker cable to the speaker.
  • Page 32 Lay the two 6mm / 1/4" thick distance blocks on the bottom of the cutout hole. Place the distance blocks so the speaker strap and mounting pins will not rest on them.
  • Page 33 Check that the rubber mounting pins are retracted into the speaker cabinet before installing it. If the mounting pins are extended from the speaker cabinet, retract them by pressing the levers on the side of the cabinet towards the center of the speaker. While the mounting pins are retracted, insert the supplied Allen Key into the small hole on the front of the cabinet, then tighten the set screws to hold the mounting pins in place.
  • Page 34 Place the spring released bottom mounting pins above the correct groove. Using the Allen wrench, softly loosen the two bottom screws to release the mounting pins. Be careful not to unscrew the set screws; stop loosening when the mounting pins pop out.
  • Page 35 Make sure the speaker is level, then tighten the bottom set screws to secure the spring-loaded mounting pins. Remove the distance blocks so the speaker rests on the mounting pins.
  • Page 36 Position the top of the speaker so the mounting pins will be released into the correct groove. Loosen the two top spring-holding set-screws so the mounting pins are released. Be careful not to unscrew the set screws, stop loosening when the mounting pins pop out. Do not retighten these again.
  • Page 37 Push the straps into the gap between the speaker and wall. This completes the installation of the speaker.

  • Page 38: S-15Iw And S-16Iw With Grills

    INSTALLATION MANUAL S-15IW AND S-16IW WITH GRILLS...
  • Page 39 UNPACKING ..................... 40   INVENTORY ..................... 40   POSITIONING OF PRODUCTS ................ 41   SPEAKER INSTALLATION ................46  ...

  • Page 40: Unpacking

    Contact both the shipper and your Steinway Lyngdorf representative immediately if products bear any sign of damage or if there is a discrepancy in the number of packages received. All Steinway Lyngdorf equipment is carefully inspected before leaving our factory. Note: Keep the shipping carton and all packing material for future use or in the unlikely event that products require servicing.

  • Page 41: Positioning Of Products

    POSITIONING OF PRODUCTS  The center of the front speaker tweeter should be in level with the primary listening position, which is approximately 1m / 3ft depending on the height of the seat.  Surround and rear speakers tweeter center should be 180cm / 6ft from the floor.
  • Page 42 S-15IW The S-15IW speaker weighs 3.5kg / 7.7lbs. Screws and wall framing must be able to support this weight. This speaker has screw terminals; please use a Phillips head screwdriver. Recommended minimum up to 16m / 50ft: AWG 14/2 or 2-lead 2mm Recommended minimum from 16m / 50ft and up: AWG 12/2 or 2-lead 3.5mm Recommended maximum: Double AWG 10/2 or 2-lead 5mm Cutout Template...
  • Page 43 Installation Bracket The distance between the top and bottom installation bracket must be 280mm / 11in. The width of the installations bracket is 35.5cm / 14in.
  • Page 44 S-16IW The S-16IW speaker weighs 5.7kg / 12.6lbs. Screws and wall framing must be able to support this weight. This speaker has screw terminals, please use a Phillips head screwdriver. Recommended minimum up to 16m / 50ft: AWG 14/2 or 2-lead 2mm Recommended minimum from 16m / 50ft and up: AWG 12/2 or 2-lead 3.5mm Recommended maximum: Double AWG 10/2 or 2-lead 5mm Cutout Size...
  • Page 45 Installation Bracket The distance between the top and bottom installation bracket must be 300mm / 11.8in. The width of the installations bracket is 35.5cm / 14in.

  • Page 46: Speaker Installation

    SPEAKER INSTALLATION All-in-one 5/8in and 13mm Wall Mounting Bracket The mounting bracket is constructed to accommodate four different wall thicknesses:  5/8”  2 x 5/8”  13mm  2 x 13mm To install the bracket correctly in a 5/8” or 2x5/8” wall you must be able to read the 5/8” text of the bottom bracket.
  • Page 47 Screw the mounting distance block and two angled brackets onto an installation bracket.
  • Page 48 Insert the frame into the cutout and fix it gently with clamps on each side of the frame in the center of the hole.
  • Page 49 Insert the bottom bracket into the hole and make sure the mounting distance guide is resting on the edge of the frame. Pull the bracket forward until it sits firmly against the frame.
  • Page 50 Screw the bracket securely into the left and right studs. The bracket is intentionally cut slightly shorter than the distance between the studs and the angled brackets will flex when screwed into the studs.
  • Page 51 Remove the mounting distance guide.
  • Page 52 Repeat the above steps to install the top bracket. Make sure the bracket is facing the correct way. If you can read 13mm or 5/8” on the bottom bracket, turn the top bracket upside down so the same text points downwards.
  • Page 53 Drill four holes through the frame into the mounting brackets. We recommend drilling 3mm / 0.12in wide and 60mm / 2.4in deep holes. Do not drill the holes so the screws will interfere with the speakers mounting pins. Insert the supplied screws for the frame and screw in tightly onto the brackets.
  • Page 54 Release the clamps.
  • Page 56 Connect the speaker cable to the speaker.
  • Page 57 Lay the two 6mm / 1/4" thick distance blocks on the bottom of the cutout hole. Place the distance blocks so the speaker strap and mounting pins will not rest on them.
  • Page 58 Check that the rubber mounting pins are retracted into the speaker cabinet before installing it. If the mounting pins are extended from the speaker cabinet, retract them by pressing the levers on the side of the cabinet towards the center of the speaker. While the mounting pins are retracted, insert the supplied Allen Key into the small hole on the front of the cabinet, then tighten the set screws to hold the mounting pins in place.
  • Page 59 Place the spring released bottom mounting pins above the correct groove. Using the Allen wrench, softly loosen the two bottom screws to release the mounting pins. Be careful not to unscrew the set screws; stop loosening when the mounting pins pop out.
  • Page 60 Make sure the speaker is level, then tighten the bottom set screws to secure the mounting pins. Remove the distance blocks so the speaker rests on the mounting pins.
  • Page 61 Position the top of the speaker so the mounting pins will be released into the correct groove. Loosen the two top spring-holding set-screws so the mounting pins are released. Be careful not to unscrew the set screws, stop loosening when the mounting pins pop out. Do not retighten these again.
  • Page 62 Push the straps into the gap between the speaker and wall.
  • Page 63 Mount the grill by pushing it gently into the frame until it snaps in place This completes the installation of the speaker.

  • Page 64: In-Ceiling S-16Iw

    INSTALLATION MANUAL IN-CEILING S-16IW...
  • Page 65 UNPACKING ..........................66 INVENTORY ..........................66 PREINSTALLATION ........................67 SPEAKER INSTALLATION ......................70...

  • Page 66: Unpacking

    Contact both the shipper and your Steinway Lyngdorf representative immediately if products bear any sign of damage or if there is a discrepancy in the number of packages received. All Steinway Lyngdorf equipment is carefully inspected before leaving our factory. Note: Keep the shipping carton and all packing material for future use or in the unlikely event that products require servicing.

  • Page 67: Preinstallation

    PREINSTALLATION S-16IW The S-16IW speaker weighs 5.7 kg / 12.6 lbs. Screws and in-ceiling backbox must be able to support this weight. This speaker has screw terminals: please use a Phillips head screwdriver. Recommended minimum up to 16m / 50ft: AWG 14/2 or 2-lead 2mm Recommended minimum from 16m / 50ft and up: AWG 12/2 or 2-lead 3.5mm Recommended maximum: Double AWG 10/2 or 2-lead 5mm Cutout Hole Height and Width...
  • Page 68 Cutout Hole Depth There must be 135-137mm or 5.31-5.39in from the rear of the backbox to the front of the cutout.
  • Page 69 In most cases it will be necessary to install a custom support between the backbox and joist. This support must be able to support the weight of the backbox and speaker.

  • Page 70: Speaker Installation

    SPEAKER INSTALLATION Insert the backbox into the hole and place it center in the cutout. Screw the bracket securely onto the ceiling. Screws not included. There are 4 pre-drilled holes in the backbox; they are 4,5mm / 0.18in in diameter. Connect the speaker cable to the speaker.
  • Page 71 Attach the safety wire and secure it to ceiling joist. Safety wire not included. Use a wire of sufficient gauge to support the weight of the speaker and backbox. Check that the rubber mounting pins are retracted into the speaker cabinet before installing it. If the mounting pins are extended from the speaker cabinet, retract them by pressing the levers on the side of the cabinet towards the center of the speaker.
  • Page 72 Be careful not to unscrew the set screws, stop loosening when the mounting pins pop out. Do not retighten the screws again. Make sure the mounting pins are properly inserted into the holes before continuing. After releasing the bottom mounting pins, release the top pins. Make sure all four mounting pins are properly inserted into the holes before continuing.
  • Page 73 Push the straps into the gap between the speaker and backbox. Screw the frame onto the backbox using the supplied screws. Mount the grill by pushing it gently into the frame until it snaps in place.
  • Page 74 This completes the installation of the speaker.
  • Page 75 TRADEMARKS DTS is a registered trademark & the DTS logos and Symbol are trademarks of DTS, Inc. Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol, DTS-HD Master Audio are trademarks of DTS, Inc.

  • Page 76: Service Information

    SERVICE INFORMATION In order to obtain warranty service you must contact your original dealer or the Steinway Lyngdorf distributor of the region or country where you are located. If you have trouble locating an authorized representative, please contact the Steinway Lyngdorf Customer Service Department using the contact information at www.steinwaylyngdorf.com, or you may email service@steinwaylyngdorf.com.

This manual is also suitable for:

In-wall series

Table of Contents