Delay Timeleffect; Channel Level - Teac AD-G9320 Owner's Manual

Test tones are automatically emitted from the different
speakers. Listen to the test tone and adjust the volume
level of each speaker so that they produce the test tone
at the same volume leveL
o~
II
I
I
~O
.-
o
0
rr=:=J 00000000
~
..
0
@
l
00
L-
0
!
0
0 0
rrcr~~
©@@
f
~
~
j
I
b. \A/hen Dolby PRO LOGIC Mode
• Main Speaker: LARGE
~
SMALL
• Center Speaker: LARGE
~
SMALL -. NONE
c. When
Dolby 3 Stereo Mode
• -MatnSpeaker :LAfiGC
~
S-MALL
• Center Speaker: LARGE
+-t
SMALL
• SUBWOOFER
output
- SUB-ON: The mode to choose
if
a subwoofer is
used. Low frequencies of 90Hz and below in the LFE
channel and other selected channels are output to
the
subwoofer.
- SUB-OFF: The mode to choose
if
no subwoofer is
used. Low frequencies of 90Hz and below in the LFE
channel and other selected channels are distributed
between the main Land R speakers.
I
Delay Time/Effect
Channel Level
I
POWER ON
1 I 1
231/4
2. Each press of the LEVEL TRIM
button during test tone
emission allows you
to
manually skip to
the
speaker
you want to listen to.
1. Press the TEST TONE button. {Dolby Digital! Dolby
PRO LOGIC Mode}
The
test tone is emitted from
each speaker
in the
following order at
2-second
intervals.
C
L
~
C
~
R
~
RS
--t
LS
~
SUB
J
I
1/2
o~
II
I
I
~O
-
0
00000000
Q
~
a
0
CD
~
00
o
0
C9~Ws !~
0
@@@
~
--
P
POWER ON
1. The
delay
time
can
be
individually
set for the
.. DOLBY DiGITAL/DOLBY PRO LOGIC modes using the
DELAY TIME (CENTER/REAR) button. When you
adjust the delay
time in the
DOLBY
DIGITAL moder
an
additional 15 ms is automatically added to the
surround
channels in
the
DOLBY PRO
LOGIC mode.
The current setting is shown on
the
display.
Delay Time Setting
Surround Mode Adjustable Range
DOLBY DIGITAL
o-
15
ms
in 1 ms step (S-Del
ay)
o -
5 ms in 1 ms step (C-Delay)
DOLBY PRO LOGIC 15 ..., 30 ms in 1
ms
step (S-Delay)
3. Use the SELECT (TjA)
buttons
to adjust the
volume until the sound level from each speaker is the
same. The volume can be adjusted in units to 1 dB
from -10 dB to +10 dB.
4. Press the TEST TONE button again to turn
it
off.
Note:
• If certain speakers
are not
being used/ (for example,
no center speaker) the noise sequencer will auto-
matically
skip over
that channel.
• Prsee the LEVEL TRIM button for more than 2
seconds to reset the level to its original setting.
In the surround modesr
the
sound from the rear
speakers should be delayed slightly, relative to that
from the front speakers. The optimum delay time will
depend on acoustic properties, whether the walls and
furnishings reflect or absorb sound/ etc.
It is recommended that you try different delay times to
obtain the best
effect.
The delay is digitally synthesized,
for the highest sound
quality
with minimum noise and
distortion.
The delay time can be set independently for each
surround mode using the DELAY TiME button, with the
4'
current setting shown in the display.
. 21 -