Table of Contents

Advertisement

Quick Links

R A D I A N T H E AT I N G S Y S T E M S
CLIMATE CO ˘ NTROL™ -
MULTIFUNCTION
INSTALLATION GUIDE
Uponor Climate Co ˘ ntrol
-
TM
Multifunction Installation Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Climate Control-Multifunction and is the answer not in the manual?

Questions and answers

Summary of Contents for Uponor Climate Control-Multifunction

  • Page 1 R A D I A N T H E AT I N G S Y S T E M S CLIMATE CO ˘ NTROL™ - MULTIFUNCTION INSTALLATION GUIDE Uponor Climate Co ˘ ntrol Multifunction Installation Guide...
  • Page 2: Table Of Contents

    Modulating Valves and Mixing ......15 Uponor Climate Co ˘ ntrol™ - Multifunction Installation Guide Pump Connections .
  • Page 3: System Overview

    Setting-up Primary Pump Functionality ..... . . 31 Uponor introduces Climate Co ˘ ntrol™ - Multifunction, the industry’s first Setting-up Mixing Functionality ......31 control systems platform that supports all functions required in today’s...
  • Page 4: Section 2 - System Functionality

    Climate Co ˘ ntrol - Multifunction system provides heat to melt snow and ice. If boiler protection is needed, the system will reduce the heat output of the snow-melt system. www.uponor-usa.com • www.uponor.ca Uponor Climate Co ˘ ntrol™ - Multifunction Installation Guide...
  • Page 5: Semi-Automatic Control

    • Read the instructions. Do not make changes or modifications specified • High outdoor temperature limit — Snow melting is disabled when in this guide. Uponor is not responsible for damages and breakdowns the outdoor temperature exceeds a determined value.
  • Page 6: Installation

    Backplate for Main Control Main Controller Cover for Outputs (RJ45) Important: Read the following installation instructions prior to installing the display and main control. It will prevent any unnecessary rework. www.uponor-usa.com • www.uponor.ca Uponor Climate Co ˘ ntrol™ - Multifunction Installation Guide...
  • Page 7: Mounting The Control Panel

    The display and main control are packaged as a single unit, assembled and 9. Use the access holes in the back of the pre-wired for operation. Uponor recommends mounting the main control panel to secure to the wall or surface.
  • Page 8: Wiring Connections For The Climate Co ˘Ntrol - Multifunction Control Board

    The bottom four connectors are fully programmable outputs. When active, LEDs for the inputs and outputs will turn green. Figure 4-6 Figure 4-6 www.uponor-usa.com • www.uponor.ca Uponor Climate Co ˘ ntrol™ - Multifunction Installation Guide...
  • Page 9: Boiler Connections

    Port 8 Typical heating device (e.g., boiler) Figure 4-8: Typical wiring of four boiler stages Figure 4-7: Typical wiring of a heating device using an Uponor Boiler Control (A9012010) for space heating www.uponor-usa.com • www.uponor.ca Uponor Climate Co ˘ ntrol™ - Multifunction Installation Guide...
  • Page 10: Modulating Condensing Boilers

    Figure 4-9: Typical wiring of a heating device using boiler control for space heating Input 8 Port 8 Figure 4-10: Typical wiring of a modulating valve in a mixing application using Uponor Modulating Valve Control (A9063020) www.uponor-usa.com • www.uponor.ca Uponor Climate Co ˘ ntrol™ - Multifunction Installation Guide...
  • Page 11: Pump Connections

    Port 4 Input 4 The Climate Co ˘ ntrol - Multifunction unit supports variable speed injection mixing, which requires an Uponor Pump Relay Box (A9013030). (See Pump Manual Port 5 Input 5 Connections below for additional information on wiring.) Uponor promotes...
  • Page 12 Circulator or Circulator ( 2 amps Max ) ( 2 amps Max ) ( 2 amps Max ) Figure 4-13. Single- and double-gang electrical box with switch www.uponor-usa.com • www.uponor.ca Uponor Climate Co ˘ ntrol™ - Multifunction Installation Guide...
  • Page 13: Snow-Melt Connections

    - Multifunction supports snow-melt operation through The Climate Co ˘ ntrol - Multifunction System supports automatic snow-melt the Uponor Snow Melt Control (A9013051). The Snow Melt Control, which operation when using Uponor Automatic Snow and Ice Sensor (A9013052). wires to the main control panel using a Cat5 cable and RJ45 ends for simple...
  • Page 14: Wiring And Connection Template

    • The wiring compartments are enclosed. of the descriptions to indicate if that connection is wired. Use the section • The display is lit and showing the Uponor logo, default date and time provided for Programmed Output Ports in the same manner.
  • Page 15: Setting The Date And Time

    The date and time screen will automatically appear when the controller To adjust the display's backlighting to change the backlight settings, follow is turned on for the first time. Access this menu at: Uponor Screen > Settings this path: Uponor Screen > Settings > System Settings > Backlight >.
  • Page 16: Viewing Mix Channel Information

    To view this information, follow this path: Uponor Screen > Information > Functions > Snow Melt > • Press  or  for the right setting, then press OK. [Channel Choice — only available if two zones of snow melt are set up.] •...
  • Page 17: Viewing Domestic Hot Water (Dhw) Information

    To view this information, This section helps the user understand this follow this path: Uponor Screen > Information > Functions > DHW >. control's full power and flexibility. (The use of the > symbol indicates pressing the OK button.)
  • Page 18: Setting-Up Domestic Hot Water (Dhw) Functionality

    To access the port assignment automatically start and manage the boiler. menu, follow this path: Uponor Screen > Settings > Ports > Port x (where x • Press  or  for the right setting, then press OK.
  • Page 19: Heating Function

    • Press  or  for the right setting, then press OK. • Using the keys, set the information correctly to match the system; then press OK to accept the information. www.uponor-usa.com • www.uponor.ca Uponor Climate Co ˘ ntrol™ - Multifunction Installation Guide...
  • Page 20: Sm (Snow-Melt) Function

    To access the port assignment menu, follow this path: • Idle Enable — This setting indicates Uponor Screen > Settings > Ports > Port x (where x is any available port) > whether the slab or snow-melt area will Mix Device >.
  • Page 21: Clearing Port Functions

    Clear All Settings selection. Using this controller command will clear all port assignment. To access this setting, follow this path: Uponor Screen > Settings > Ports > Clear All Output light is on, • Output •...
  • Page 22 Uponor, Inc. 5925 148th Street West Apple Valley, MN 55124 USA Tel: (800) 321-4739 Fax: (952) 891-1409 Web: www.uponor-usa.com Uponor Ltd. 655 Park Street Regina, SK S4N 5N1 CANADA Tel: (888) 994-7726 Fax: (800) 638-9517 Web: www.uponor.ca...

Table of Contents