Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Fetco PEL0101
- Page 1 Posted 10-17-16...
-
Page 3: Table Of Contents
Index Page A quality choice………………………………..……………………………………… 4 General instructions and warnings…………………………………………… 5 Installing the new machine…..……………….………………………………… 6 Cleaning…………………………………………………………………………………… 7 Long feet………….……………............9 First Class Millennium controls and signals ……………………………... 9 How to start the production of slush, sherbets or cold drinks.…. 13 Important security rules……………………….……....... -
Page 4: A Quality Choice
A quality choice FETCO by Elmeco business is managed in according with rules of Vision 2000 and ISO 14001 Choosing FETCO by Elmeco, and in particular First Class, the new and only multifunctional machine with double augers, demonstrates your attention to innovation. -
Page 5: General Instructions And Warnings
General instruction and warnings Before switching on the machine carefully read the information in this service manual; this way you will be able to install, use and maintain the machine. Keep the use and assembly instructions, even for the next buyer. The manufacturer declines any responsibility for damages deriving from the non-observance of the following instructions. -
Page 6: Installing The New Machine
(pic. 2 and 3). Only specialized and authorized staff can repair the machine. Not perfect repairing can be dangerous for the user. contact Fetco for information concerning the closest authorized service center. For safe operation the maximum tilt of the appliance is 1,5 degree towards the front side (outlet). -
Page 7: Cleaning
Lid stickers All refrigerators are equipped with 2 stickers for each single lid. The stickers must be applied as showed in the pictures: Right usage Before switching on the machine, it is necessary to clean it as indicated in the “Cleaning” paragraph. Cleaning Always comply with the provisions of the local authorities in charge regarding the cleaning of the machine. - Page 8 Remove the horizontal auger; this way the inox side of the tank is completely open and ready to be cleaned (pic. 18 and 19 in appendix-88). Remove the outlet (pic. 20, 21, 22, 23 in appendix-88) and the tank gasket (pic. 24 in appendix- 88): ...
-
Page 9: Long Feet
Long feet (only for 115Vac/60Hz) The units First Class 2 and First Class 3 with voltage 115Vac/60Hz are equipped with 4 long feet (4 inches) that must be installed at the place of the short 4 feet already mounted. This installation is obligatory in conformity of NSF rules. This long feet aren’t adjustable in height. - Page 10 After the screen shown above the initial screen will be displayed: StandBy Warning! The electronic board will keep the settings it had Press when the machine was switched off. When the tank is in stand-by mode, the augers and the cooling system are off.
- Page 11 pressing the increase key or the decrease key. If you add some product (liquid that touches the level probe), the function will be deactivated and the slush Please / refill / LOWLEVEL preparation will reach the density value that was previously set on the electronic board.
- Page 12 1) press the button; 2) the first value of “defrost ON” will start to blink. If you want to change the value, you need to press button; 3) repeat the steps 1) and 2) until all ON values are set; button to exit the change function of “defrost ON”...
-
Page 13: How To Start The Production Of Slush, Sherbets Or Cold Drinks
Operator security If you open the tank lifting the lamp, the augers will stop. Self-diagnostics Consult the Problem Solving Section. Configuration memory All the functioning modes and the regulations set are registered in a non-volatile memory which is active even without power; therefore, when you switch on the machine, the tank keeps the configuration it had when you switched it off, a part from the keyboard lock (as already said). -
Page 14: Important Security Rules
With the “slush” mode: SLUSH Slush. It is possible to change the product density from 1 to 9 using the buttons to increase or decrease it respectively. With the “cold drink” mode: Cold drink. COLD It is possible to change the product temperature from +2°C to +5°C using the buttons to increase or decrease it respectively. -
Page 15: Old Machine Disposal
Old machine disposal The out-of-use machines must be disabled. Disconnect the plug from the electrical network and cut the cable. Ecological instructions All refrigerating machines must be disposed by the communal disposal service or by an equivalent private authorized company. Take care not to damage the rigid tubes of the refrigerator until they are taken back in order to be carefully and ecologically disposed. -
Page 16: Pressure Switch Refit Procedure
Pressure switch refit procedure Warning! The following steps must be performed by qualified personnel. When the pressure switch light, near main switch in ON, this indicates that the pressure switch intervened to deactivate the compressor. In order to refit this device, it is important to follow the instructions below: 1°... -
Page 17: Problem Solving
First Class Problem Solving 1. Switch off the slush machine with the main switch; The tank does not make cold, the 2. discharge the product, if it is cold, and put in the tank a product with a temperature higher than 15°C; cooling light is off 3. -
Page 18: Warranty Certificate
Warranty Certificate Dealer stamp and signature _ _/_ _/_ _ Purchase date Model FC__ (1, 2 or 3) Serial number _ _ _ _ _ _ _ _ _ _ Dealer………………........Data of the purchaser Date..………......... Street……………………................................. State……………………...City .......... Zip Code ...... - Page 19 ELECTRIC WIRING DIAGRAM...
- Page 20 ELECTRIC WIRING DIAGRAM LEGEND Main switch Pr: Pressure switch LPr: Pressure switch light Compressor FM: Fan motor TR: Transformer Fuse 5x20mm 5A Fuse 5x20mm F315mA EV1-2-3: Solenoid valve M1-2-3: Gear motor EB1-2-3: Electronic board EM: Machine module H1-2-3: Magnetic reader L1-2-3: Top light P1-2-3: Level probe R1-2-3: Heating element 100Kohm-0.25W...
-
Page 21: Refrigerating System
Refrigeration System C: Compresor Cn: Condensor F: Filter Drier B: Boiler ev1: Solenoid Valve ev2: Solenoid Valve ev3: Solenoid Valve E1: Evaporator E2: Evaporator E3: Evaporator 1: Condenser Líne 2: Líquid Line 3: Suction Line Pr: Pressure Switch... -
Page 22: Exploded View
Exploded Views and Parts Identification... - Page 23 REPLACEMENT PARTS (CONTACT FACTORY PRIOR TO ORDERING) PART NUMBER DESCRIPTION M0004109-002 RING NUT HORIZONTAL AUGER M0003126-001 RING NUT LEVER COVER PISTON + STAINLESS STEEL ROD M0003126-003 RING NUT LEVER COVER PISTON + PLASTIC ROD M0003139-001 HANDLE + COVER OR13000117 O-RING 117 M0003117-001 OUTLET GASKET M0006134-001...
- Page 25 FETCO CALLING OR ITS AUTHORIZED PARTNERS The model and serial number shall be supplied to the service department of FETCO along with the defective parts or unit. The dealers, distributors, employees and agents of FETCO are not authorized to modify this warranty neither written nor...
- Page 26 FETCO® Technical Support: techsupport@fetco.com Food Equipment Technologies Company 600 Rose Road General Inquiries: info@fetco.com Lake Zurich , IL 60047-0429 USA Sales North America: sales@fetco.com Phone: (847) 719-3000 Toll Free: (800) FETCO.99 or (800) 338-2699 Sales (International): international@fetco.com Website: www.fetco.com...
Need help?
Do you have a question about the PEL0101 and is the answer not in the manual?
Questions and answers