Related Manuals for Anrtisu Lightning 37000D
Summary of Contents for Anrtisu Lightning 37000D
- Page 1 Technical Datasheet and Configuration Guide Lightning ™ 37000D Vector Network Analyzers 40 MHz to 65 GHz 37000D Series Network Analysis Solutions for Design and Manufacturing...
-
Page 2: System Description
System Description The Lightning D series microwave and millimeter-wave Vector Can be entered in time or in distance (when the Reference Plane: Network Analyzers encompass a wide range of high performance dielectric constant is entered). Automatic reference plane feature component and system test tools designed to address the growing adds the correct electrical length (delay) compensation. - Page 3 Blanking function removes all Power meter correction is available at a Blank Frequency Information: Power Meter Correction: references to frequencies on the display. Frequency references can user-selectable power level, if it is within the power adjustment only be restored through a system reset or GPIB command. range of the internal source.
- Page 4 Connectivity 240 kB/sec GPIB Data Transfer Speed (with or without cal): 2 Ports, system GPIB and dedicated GPIB GPIB: Throughput measurements for both GPIB Data Throughput Time: tables were made as follows: start the timer, trigger a sweep, wait Connects to an external controller for System GPIB (IEEE-488.2): for a full sweep, transfer data across the GPIB and stop the timer.
- Page 5 Storage Interfaces 0.5 GB, used to store and recall Internal Hard Disk Drive: Front Panel Connectors and Controls: measurement and calibration data and front-panel setups. File Any PS-2 keyboard can be connected to the Keyboard Input: names can be 1 to 8 characters long, and must begin with a front panel for navigating through front panel menus, annotation character, not a number.
- Page 6 Options A selective gating function may be applied to the time domain Time (Distance) Domain Measurement Capability (Option 2A) Gating: data to remove unwanted responses, either in a pass-band or reject- High Speed Time (Distance) Domain option allows the conversion band (mask).
- Page 7 Corrected Specifications 37X47D (40 MHz – 20 GHz) is defined as the difference between the available power from Port 1 incident on Port 2 in a through line connection and System Dynamic Range the noise floor. 10 Hz I.F. Bandwidth, 101 pts, 12-term SOLT calibration, 512 averages VNA settings: Port 1 Power, Typical (dBm) Noise Floor at Port 2 (dBm)
- Page 8 37X69D (40 MHz – 40 GHz) Port 1 Power, Typical (dBm) Noise Floor at Port 2 (dBm) System Dynamic Range (dB) Frequency Model (GHz) With Option 15 With Option 15 With Option 15 0.04 –85 –85 –107 –107 37369D –103 –102 –95 –94...
- Page 9 37X77D (40 MHz – 50 GHz) Port 1 Power, Typical (dBm) Noise Floor at Port 2 (dBm) System Dynamic Range (dB) Frequency Model (GHz) With Option 15 With Option 15 With Option 15 0.04 –88 –88 –110 –110 37377D –106 –105 –98 –97...
- Page 10 37X97D (40 MHz – 65GHz) Port 1 Power, Typical (dBm) Noise Floor at Port 2 (dBm) System Dynamic Range (dB) Frequency Model (GHz) With Option 15 With Option 15 With Option 15 0.04 –88 –88 –110 –110 –106 –105 37397D –98 –97 –1...
- Page 11 Signal Source Specifications Power Flatness 1 Hz Resolution: Frequency Flatness (dB) Frequency Stability 40 MHz – 13.5 GHz ±1.5 Temperature: < 5x10 over 0° to 55°C range –9 13.5 GHz – 20 GHz ±2.0 Aging: <1 x 10 /day –9 20 GHz –...
- Page 12 37200D Block Diagram Source Transfer Switch Port 1 Port 2 a1 (Ra) a2 (Rb) Sampler/Buffer Amplifier b1 (Ta) b2 (Tb) Coupler Coupler Port 1 Port 2 37200D Block Diagram with Option 15 Source Transfer Switch Input Input External External Source Source Loop Loop...
- Page 13 37300D Block Diagram Source Step Attenuator Transfer Switch Bias Bias Bias Bias Port 1 Port 2 Port 1 Port 2 a1 (Ra) a2 (Rb) Step Sampler/Buffer Attenuator Amplifier b1 (Ta) b2 (Tb) Coupler Coupler Port 2 Port 1 Port 2 37300D Block Diagram with Option 15 Source Step...
-
Page 14: Ordering Information
Ordering Information Models Calibration Kits Using Anritsu’s precision calibration kits ensures accurate operation of your 37200D Economy Vector Network Analyzers 37000D series VNA. These kits include precision components required to (see page 11 for block diagram) perform full 12 term calibrations. The AutoCal modules are automatic ®... - Page 15 Measurement Accessories Test Port Cables MN4765A O/E Calibration Module (40 MHz-65 GHz) Flexible, High Performance, Phase Stable Unamplified photodiode module. Characterized to 65 GHz in K(f) - GPC-7 Cables, 63.5 cm (25 in.), one pair 3671A50-1 both magnitude and phase using a NIST traceable standard. K(f) - GPC-7 Cable, 96.5 cm (38 in.) 3671A50-2 Used for electro-optical and opto-electrical measurements...
- Page 16 UTF Calibration/Verification Kits Other Accessories and Tools 36804B-10M 10 mil Microstrip Calibration/Verification Kit, DC to 60 GHz Lightning Transit Case 760-231 36804B-15M 15 mil Microstrip Calibration/Verification Kit, DC to 40 GHz 5/16” Torque Wrench, 8 ft-lbs, for SMA, 3.5 mm, and 01-201 36804B-25M 25 mil Microstrip Calibration/Verification Kit, DC to 20 GHz K Connectors...
Need help?
Do you have a question about the Lightning 37000D and is the answer not in the manual?
Questions and answers