Philips FM23 AC Service Manual page 25

NORMAL OPERATION
RC button,
e.g. P+ or P-
STANDBY
RC sequence "0-6-2-5-9-6-OSD "(for Europe & A/P)
or
RC sequence "0-6-2-5-9-6-INFO+" (for USA/LatAm)
or
Short SAM pins (works also from Standby)
Do not store
settings made
during alignments
Ignore all "Service
unfriendly" modes
RC button,
e.g. P+ or P-
"UNDO" ignore
all "Service
unfriendly
RC sequence
modes"
"00" Service Alignment Mode
Display "SAM" top level
"Standby"
menu
Settings made
during alignments
are stored
STANDBY
Figure 5-2 SAM Flowchart
How to enter
Use one of the following methods:
•
Use a standard RC-transmitter and key in the code 062596
directly followed by the OSD (i+) button.
Note: the OSD (i+) is not available on the original FTV
remote control; therefore use another Philips remote
control (e.g. MG, EMG or A10).
•
Short jumpers 3 and 4 of connector 0382 on the SCAVIO
panel.
The following screen is visible:
Table 5-1 SAM Menu "General"
Service Alignment Menu
Type Nr. - AG Code 32FD9944/01S (example)
SW Version OTC AAAABC-X.Y_xxxxx
SW Version PW AAAABC-X.Y_xxxxx
SW Version EPLD AAAABC-X.Y_xxxxx
Errors 1 xx xx xx xx xx
Errors 2 xx xx xx xx xx
Operational hours xx
Reset error buffer Press OK to reset
Store Press OK to store
1. TYPE NR. Gives the commercial type number of the
monitor, e.g. 32FD9944/01S.
2. AG CODE. Is not implemented.
3. SW VERSION OTC (AAAABC-X.Y-xxxxx).
Note: You will find details of the latest software versions in
the chapter "Software Survey" of the "Product Survey -
Colour Television" publication, which is published four
times each year.
•
A = the chassis name (FM23 for all displays).
•
B = the region (E= Europe, A= Asia Pacific, U= NAFTA,
L= LATAM or G = Global).
•
C = the configuration name (B= Basic, E= Enhanced).
•
X = the main software version number.
•
Y = the sub software version number.
•
x = last five digits of 12nc code.
4. SW VERSION PW (AAAABC-X.Y-xxxxx). See description
above.
Service Modes, Error Codes, and Fault Finding
Mains ON
OFF
(Settings made
during alignments
are stored)
Mains OFF
RC-code "0-6-2-5-9-6-OSD"
SDM
or
RC-code "0-6-2-5-9-6-INFO+"
RC-code "0-6-2-5-9-6-MENU" -
Upper menu selection
SAM submenus
(with cursor buttons)
(whitepoints, align-
Lower menu selection
ments, etc.)
(with cursor buttons)
CL 16532099_101.pdf
260901
General
FM23, FM24, FM33
5. SW VERSION EPLD (AAAABC-X.Y-xxxxx). See
description above.
6. ERRORS 1. Gives the last five errors of the error buffer.
The last detected error is displayed at the most left
position. The errors are displayed as 2 digit numbers and
separated by a space. When less than 10 errors occurred,
the rest of the line(s) is empty. In case of no errors, the text
"No Errors" is displayed behind menu item "Errors 1". See
paragraph 5.5 for a description.
7. ERRORS 2. Gives the first five errors of the error buffer.
The last detected error is displayed at the most left
position.
8. OPERATIONAL HOURS. The Operations Hours indicate
the time that the display was active with half an hour
resolution. It represents the system hours (OTC), not the
PDP hours.
9. RESET ERROR BUFFER. Erase the contents of the error
buffer. Press "OK" on your remote control to activate. The
content of the error buffer is cleared.
10. STORE. This will store the performed alignments. Press
"OK" on your remote control to activate.
Note: if you do not want to store the performed alignments,
leave the SAM mode via code 0 0 on your remote control.
Do not activate the "store" item.
How to navigate
Use one of the following methods:
•
Select the sub-menu's (upper line) with the CURSOR
LEFT/RIGHT keys on the remote control transmitter.
•
Select the menu items with the CURSOR UP/DOWN keys.
With the CURSOR LEFT/RIGHT keys it is possible to:
–
Activate the selected menu item.
–
Change the value of the selected menu item.
•
To toggle to the SDM mode, use the standard customer
RC-transmitter and key in the code 062596, directly
followed by the MENU key.
How to exit
Use one of the following methods:
•
Switch the set "off" (with the Mains switch or by pulling the
Mains cord).
Note: new alignment settings are always stored, even
when item "store" was not activated!
•
Switch the set to "standby" by pressing the power button on
the remote control transmitter.
Note: new alignment settings are always stored, even
when item "store" was not activated!
•
Use the standard RC-transmitter and key in the code 00.
Note: new alignment settings are not stored (except when
item "store" was activated)!
5.2.3
Customer Service Mode (CSM)
Purpose
When a customer is having problems with his TV-set, he can
call his dealer or helpdesk. The service technician can than ask
the customer to activate the CSM, in order to identify the status
of the set. Now, the service technician can judge the severness
of the complaint. In many cases, he can advise the customer
how to solve the problem, or he can decide if it is necessary to
visit the customer.
The CSM is a read only mode; therefore, modifications in this
mode are not possible.
5. EN 25